Schwinn 240 Recumbent Bike Owner's Manual - Page 20

Contact Customer Care for further

Get Schwinn 240 Recumbent Bike PDF manuals and user guides View all Schwinn 240 Recumbent Bike manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Console displays "E2" error code Check data cable integrity Check data cable connections/orientation Console Electronics No speed/RPM reading, Console displays Check data cable integrity "E3" error code Check data cable connections/orientation Check magnet position (requires shroud removal) Check RPM Sensor (requires shroud removal) Console shuts off (enters sleep mode) while in use Check data cable integrity Check data cable connections/orientation Reset Machine (if equipped with reset button) Check magnet position (Technician onlyrequires shroud removal) Check RPM Sensor Fan (if equipped) will not turn on or will not turn off Check data cable integrity Check data cable connections/orientation Unit rocks/does not sit level Reset Machine (if equipped with reset button) Check leveler adjustment Check surface under unit All wires in cable should be intact. If any are cut or crimped, replace cable. Insure cable is connected securely and oriented properly. Small latch on connector should line up and snap into place. If tests reveal no other issues, Console should be replaced. All wires in cable should be intact. If any are cut or crimped, replace cable. Insure cable is connected securely and oriented properly. Small latch on connector should line up and snap into place. Magnet should be in place on flywheel. If no magnet is present, replace the flywheel or the entire base unit (if unable to replace flywheel). RPM sensor should be aligned with magnet and connected to data cable. Realign sensor if necessary. Replace if there is any damage to the sensor or the connecting wire. All wires in the cable should be intact. If any are cut or crimped, replace cable. Insure cable is connected securely and oriented properly. Small latch on connector should line up and snap into place. Unplug unit from electrical outlet for 3 minutes. Reconnect to outlet. After the Console powers up, press "reset". Magnet should be in place on flywheel. If no magnet is present, replace flywheel or entire base unit. Contact Customer Care for further assistance. All wires in cable should be intact. If any are cut or crimped, replace cable. Insure cable is connected securely and oriented properly. Small latch on connector should line up and snap into place. Unplug unit from electrical outlet for 3 minutes. Reconnect to outlet. After Console powers up, press "reset". Leveling feet may be turned in or out to level bike. Adjustment may not be able to compensate for extremely uneven surfaces. Move bike to level area. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Check data cable integrity
All wires in cable should be intact. If any
are cut or crimped, replace cable.
Check data cable
connections/orientation
Insure cable is connected securely
and oriented properly. Small latch on
connector should line up and snap into
place.
Console displays "E2" error code
Console Electronics
If tests reveal no other issues, Console
should be replaced.
Check data cable integrity
All wires in cable should be intact. If any
are cut or crimped, replace cable.
Check data cable
connections/orientation
Insure cable is connected securely
and oriented properly. Small latch on
connector should line up and snap into
place.
Check magnet position (requires shroud
removal)
Magnet should be in place on flywheel.
If no magnet is present, replace the
flywheel or the entire base unit (if unable
to replace flywheel).
No speed/RPM reading, Console displays
"E3" error code
Check RPM Sensor (requires shroud
removal)
RPM sensor should be aligned with
magnet and connected to data cable.
Realign sensor if necessary. Replace if
there is any damage to the sensor or the
connecting wire.
Check data cable integrity
All wires in the cable should be intact. If
any are cut or crimped, replace cable.
Check data cable
connections/orientation
Insure cable is connected securely
and oriented properly. Small latch on
connector should line up and snap into
place.
Reset Machine (if equipped with reset
button)
Unplug unit from electrical outlet for 3
minutes. Reconnect to outlet. After the
Console powers up, press "reset".
Check magnet position (Technician only-
requires shroud removal)
Magnet should be in place on flywheel.
If no magnet is present, replace flywheel
or entire base unit.
Console shuts off (enters sleep mode)
while in use
Check RPM Sensor
Contact Customer Care for further
assistance.
Check data cable integrity
All wires in cable should be intact. If any
are cut or crimped, replace cable.
Check data cable
connections/orientation
Insure cable is connected securely
and oriented properly. Small latch on
connector should line up and snap into
place.
Fan (if equipped) will not turn on or will
not turn off
Reset Machine (if equipped with reset
button)
Unplug unit from electrical outlet for
3 minutes. Reconnect to outlet. After
Console powers up, press "reset".
Check leveler adjustment
Leveling feet may be turned in or out to
level bike.
Unit rocks/does not sit level
Check surface under unit
Adjustment may not be able to
compensate for extremely uneven
surfaces. Move bike to level area.
20
20
20