Schwinn 431 Elliptical Assembly Manual

Schwinn 431 Elliptical Manual

Get Schwinn 431 Elliptical PDF manuals and user guides View all Schwinn 431 Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Schwinn 431 Elliptical manual content summary:

  • Schwinn 431 Elliptical | Assembly Manual - Page 1
    Do not print this page
  • Schwinn 431 Elliptical | Assembly Manual - Page 2
    ©2007. Nautilus, Inc. All Rights Reserved. Schwinn is a registered trademark. Nautilus, Inc., World Headquarters, 16400 SE Nautilus Dr., Vancouver, WA 98683
  • Schwinn 431 Elliptical | Assembly Manual - Page 3
    elliptical Assembly guide 001-7077-072809C Assembly Guide
  • Schwinn 431 Elliptical | Assembly Manual - Page 4
    CONTENTS Table of Contents Hardware 2 Exploded View 4 Parts List 5 Assembly Instructions 6 Important Contact Numbers 19 Attention! When unpacking the box, please inspect all styrofoam and packaging before discarding. Some parts are packaged on the outside of the styrofoam packaging. 1
  • Schwinn 431 Elliptical | Assembly Manual - Page 5
    WASHER REGULAR (36) M8 x 15L BUTTON HEAD (32) M8 WASHER WIDE (4) M8 x 20L BUTTON HEAD (4) M8 WAVE WASHER (2) Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact
  • Schwinn 431 Elliptical | Assembly Manual - Page 6
    HARDWARE CARD WRENCHES (2) M8 WASHER LOCKING (40) M8 x 25L FLAT HEAD THREAD LOCK (6) ALLENWRENCH (1) END CAPS (2) Note: Please verify you have all correct parts and quantities before assembling unit. If you are missing items, are short quantities, or have damaged components, please contact
  • Schwinn 431 Elliptical | Assembly Manual - Page 7
    exploded view EXPLODED VIEW T L H GI F X O K Y R W C D E A B M U G W F S J Y N V Z Q P 4
  • Schwinn 431 Elliptical | Assembly Manual - Page 8
    PARTS LIST Ref. Description Qty A SCHWINN 431 HARDWARE CARDS 1 B SCHWINN 431 ASSEMBLY MANUAL 1 C MAIN FRAME Assembly 1 D CONSOLE HANDLE ASSEMBLY 1 E CUP HOLDER 1 F PIVOT SHOULDER COVER 2 G MOVEMENT ARM WIRE COVER 2 H CONSOLE MAST COVER 1 I CONSOLE
  • Schwinn 431 Elliptical | Assembly Manual - Page 9
    gather the pieces you need for each step and thoroughly read the assembly instructions for that step prior to starting assembly for the step. 2. When attaching two pieces, gently lift and look through the bolt holes to help guide the bolt through the holes. 3. As a general rule, and for all bolts
  • Schwinn 431 Elliptical | Assembly Manual - Page 10
    ASSEMBLY INSTRUCTIONS Step 1 Install Rear Stabilizer and Extrusion Handlebar Parts: • Two Extrusion Assemblies (Ref. V) • Rear Stabilizer (Ref. Q ) • Extrusion Handlebar Assembly (Ref. Z) Tools: • Supplied Allen Wrench 1-1 Attach, but do not tighten, the Extrusion Assemblies (Ref V) to the Rear
  • Schwinn 431 Elliptical | Assembly Manual - Page 11
    ASSEMBLY INSTRUCTIONS Step 2 Install front stabilizer and Extrusion Assembly Parts: • Front Stabilizer (Ref P) • Extrusion Assembly (From step 1) • Main Unit (Ref C) Tools: • Supplied Allen Wrench 2-1 Attach the Front Stabilizer (Ref P) to the Main Unit (Ref C) using two M8x25 flat head screws (Ref
  • Schwinn 431 Elliptical | Assembly Manual - Page 12
    ASSEMBLY INSTRUCTIONS Step 3 Install Console Mast Parts: • Console Mast (Ref I) • Main Unit Tools: • Supplied Allen Wrench 3-1 Connect the wire harness from the Main Unit to the wire harness in the Console Mast. 3-2 Slide the Console Mast (Ref I) down onto the Main Unit and secure using six M8x15L
  • Schwinn 431 Elliptical | Assembly Manual - Page 13
    ASSEMBLY INSTRUCTIONS Step 4 Install Console Handlebar Parts: • Console Handlebar (Ref D) Tools: • Supplied Phillips Head Screwdriver 4-1 Feed the Wire Harness (Ref W1) from the Mast (Ref I) and the Contact Heart Rate Wire (Ref W2) from the Console Handlebar through the hole in the Console
  • Schwinn 431 Elliptical | Assembly Manual - Page 14
    ASSEMBLY INSTRUCTIONS Step 5 Install Console Parts: • Console (Ref T) Tools: • Supplied Phillips Head Screwdriver NOTE: Before installing the console, make sure the toggle switch on the back of the Console (beside wire connectors) is set to EP. 5-1 Remove the four phillps head screws (Ref 9) from
  • Schwinn 431 Elliptical | Assembly Manual - Page 15
    ASSEMBLY INSTRUCTIONS Step 6 Install Right and Left leg Parts: • Right Leg (Ref R) • Left Leg (Ref S) Tools: • Supplied Combo Wrench 6-1 Attach the Right leg (Ref R), marked with an "R" sticker that can be removed, to the post on the Crank (Ref C1) using one M8x20L hex head thread lock (Ref 10) one
  • Schwinn 431 Elliptical | Assembly Manual - Page 16
    ASSEMBLY INSTRUCTIONS Step 7 Install Right and Left Lower Handlebars Parts: • Arm Pivot Rod (Ref X) • Right Lower Handlebar (Ref O) • Left Lower Handlebar (Ref N) Tools: • Two Supplied Combo Wrenches 7-1 Slide the Arm Pivot Rod (Ref X) through the Console removed. Use the two supplied combo wrenches thoroughly tighten the hardware.
  • Schwinn 431 Elliptical | Assembly Manual - Page 17
    ASSEMBLY INSTRUCTIONS Step 8 Install Right and Left Foot Assembly Parts: • Foot Mount Plate Qty. 2 (Ref W) • Right Foot Assembly (Ref K) • Left Foot Assembly (Ref J) • Arm Cotter Pin (Ref AC) Tools: • Supplied Allen Wrench 8-1 Slide the shaft under the Left Foot Assembly into the Pivot (Ref P1) on
  • Schwinn 431 Elliptical | Assembly Manual - Page 18
    ASSEMBLY INSTRUCTIONS Step 9 Install Upper Handlebar Covers and Upper Handlebars Parts: • Upper Handlebar Cover Qty. 2 (Ref G) • Right 9-2 Slide the Upper Left Handlebar (Ref M) into the Lower Left Handlebar and secure using four M8x15l button head (Ref 1) four M8 washers regular (Ref 3) and four
  • Schwinn 431 Elliptical | Assembly Manual - Page 19
    ASSEMBLY INSTRUCTIONS Step 10 Install Pivot Shoulder Cover Parts: • Pivot Shoulder Cover Qty. 2 (Ref F) Tools: • None 10-1 Align the Pivot Shoulder Covers (Ref F) with the holes for the Arm Pivot Rod in each of the Handlebar Assemblies (Ref N and Ref O). 10-2 Push the Pivot Shoulder Covers until
  • Schwinn 431 Elliptical | Assembly Manual - Page 20
    ASSEMBLY INSTRUCTIONS Step 11 Install AC Adapter Parts: • AC Adapter (Ref U) Tools: • None 11-1 Connect the AC Adapter (Ref U). Pre-Assembled I U 17
  • Schwinn 431 Elliptical | Assembly Manual - Page 21
    ASSEMBLY INSTRUCTIONS Assembly is complete! Please reference the Owner's Manual for information regarding computer operation, product maintenance, locating and recording the serial number, warranty information, and general fitness and exercise guidelines. 18
  • Schwinn 431 Elliptical | Assembly Manual - Page 22
    the serial number of your machine and the date of purchase (reference the Owner's Manual) available when you contact the in your area, please call or fax one of the following numbers. • INTERNATIONAL CUSTOMER SERVICE: Nautilus International S.A. Rue Jean Prouvé 6 1762 Givisiez / Switzerland Tel: + 41
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
Do not print this page