Home » Seagate Manuals » Hard Drives » Seagate FDE.2 » Manual Viewer

Seagate FDE.2 Momentus 5400.2 FDE.1 PATA Product Manual - Page 35

Drive Trust Mode supported, Table 9, Drive Trust Identify

UPC - 683728167882

Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

4.1.4 Drive Trust Mode supported Identify Page - Word 150 decimal (0x96h)- Bit 12 Identifies Drive Trust Support. Value = 1 = Drive Trust is supported (this is a trusted drive) Table 9: Drive Trust Identify Page Ident Value BIT set 0 1 5 0 1 0 0 0 0 0 1 0 9 0 1 1 0 8 0 0 Bit 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Description Vendor specific Vendor specific Vendor specific Drive Trust Enabled Vendor specific Vendor specific Vendor specific Vendor specific Vendor specific Vendor specific Vendor specific Drive Trust Supported Vendor specific Vendor specific Vendor specific Vendor specific Momentus 5400 FDE Product Manual, Rev. C 29

Section	Page
1.0 Introduction	7
1.1 System requirements	7
1.2 About Momentus 5400 FDE disc drives	8
1.2.1 Drive state upon shipment	8
2.0 Drive specifications	11
2.1 Specification summary	11
2.2 Formatted capacity	13
2.3 Default logical geometry	13
2.4 Physical organization	13
2.5 Recording and interface technology	14
2.6 Physical characteristics	14
2.7 Seek time	15
2.8 Time to ready	15
2.9 Power specifications	16
2.9.1 Power consumption	16
2.9.1.1 Typical current profile	17
2.9.2 Conducted noise	17
2.9.3 Voltage tolerance	17
2.9.4 Power-management modes	18
2.10 Environmental specifications	19
2.10.1 Ambient temperature	19
2.10.2 Temperature gradient	19
2.10.3 Humidity	19
2.10.3.1 Relative humidity	19
2.10.3.2 Wet bulb temperature	19
2.10.4 Altitude	19
2.10.5 Shock	19
2.10.5.1 Operating shock	19
2.10.5.2 Nonoperating shock	20
2.10.6 Vibration	20
2.10.6.1 Operating vibration	20
2.10.6.2 Nonoperating vibration	20
2.11 Acoustics	20
2.12 Electromagnetic immunity	21
2.13 Reliability	22
2.14 Agency certification	22
2.14.1 Safety certification	22
2.14.2 Electromagnetic compatibility	22
2.14.3 FCC verification	23
2.15 Environmental protection	24
2.16 Corrosive environment	24
3.0 Configuring and mounting the drive	25
3.1 Handling and static discharge precautions	25
3.2 Jumper settings	26
3.2.1 Master/slave configuration	26
3.2.2 Cable-select option	26
3.3 Drive mounting	26
3.4 Drive integration	28
3.4.1 Drive installation	29
3.4.2 Consumer usage	29
3.5 Security Erase--ATA security commands	29
3.5.1 Security Thaw command	29
3.5.2 Security Erase procedure	29
3.5.3 Drive State after security erase	30
4.0 ATA interface	31
4.1 ATA interface signals and connector pins	31
4.1.1 ATA interface specifications	32
4.1.1.1 Legacy mode -- Multi-word DMA not supported	32
4.1.1.2 Legacy mode -- Interrupts disabled mode (polling) supports limited functionality	32
4.1.1.3 PIO Read -- Interrupts Enabled mode	32
4.1.1.4 Device 0 only configurations	33
4.1.1.5 48-bit (Extended mode) Sector Count register must be written twice	33
4.1.2 ATA Security policy exceptions	33
4.1.3 Additional technical notes	34
4.1.4 Drive Trust Mode supported	35
4.1.5 Full Disc Encryption support	36
4.1.6 Supported ATA commands	37
4.1.7 Identify Device command	41
4.1.8 Set Features command	44
5.0 Compatibility summary	45
5.1 Installation considerations	45
5.2 BIOS versions tested	46
5.3 Operating system versions tested	47
5.4 Compatibility test configurations	47
5.5 Software utilities	47
5.5.1 Third party software support	48
6.0 Seagate Technology support services	49
Numerics	51
A	51
B	51
C	51
D	51
E	51
F	51
G	51
H	51
I	51
J	52
K	52
L	52
M	52
N	52
O	52
P	52
R	52
S	52
T	53
U	53
V	53