Home » Seagate Manuals » Hard Drives » Seagate ST2000VX000 » Manual Viewer

Seagate ST2000VX000 SV35.2 Series SATA Product Manual - Page 21

Nonoperating shock, Disc models, 3 and 4 Disc models, Vibration, 9.6.1, Operating vibration,

View all Seagate ST2000VX000 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

2.9.5.2 Nonoperating shock 1 Disc models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 2, 3 and 4 Disc models The nonoperating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration. 2.9.6 Vibration All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis. 2.9.6.1 Operating vibration The maximum vibration levels that the drive may experience while meeting the performance standards specified in this document are specified below. 5-22 Hz 22-350 Hz 350-500 Hz 0.02 inches (Limited displacement, peak to peak) 0.50 Gs 0.25 Gs 2.9.6.2 Nonoperating vibration The maximum nonoperating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below. 5-350 Hz 350-500 Hz 5.0 Gs 1.0 Gs SV35.2 Series Serial ATA Product Manual, Rev. D 15

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	14
2.2.1 LBA mode	14
2.3 Default logical geometry	14
2.4 Recording and interface technology	15
2.5 Physical characteristics	15
2.6 Seek time	16
2.7 Start/stop times	16
2.8 Power specifications	16
2.8.1 Power consumption	16
2.8.1.1 Typical current profiles	18
2.8.2 Conducted noise	18
2.8.3 Voltage tolerance	18
2.8.4 Power-management modes	19
2.9 Environmental specifications	20
2.9.1 Ambient temperature	20
2.9.2 Temperature gradient	20
2.9.3 Humidity	20
2.9.3.1 Relative humidity	20
2.9.3.2 Wet bulb temperature	20
2.9.4 Altitude	20
2.9.5 Shock	20
2.9.5.1 Operating shock	20
2.9.5.2 Nonoperating shock	21
2.9.6 Vibration	21
2.9.6.1 Operating vibration	21
2.9.6.2 Nonoperating vibration	21
2.10 Acoustics	22
2.11 Electromagnetic immunity	22
2.12 Reliability	23
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	23
2.13 Agency certification	23
2.13.1 Safety certification	23
2.13.2 Electromagnetic compatibility	23
2.13.3 FCC verification	24
2.14 Environmental protection	25
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	25
2.15 Corrosive environment	25
3.0 Configuring and mounting the drive	27
3.1 Handling and static-discharge precautions	27
3.2 Configuring the drive	28
3.3 Serial ATA cables and connectors	28
3.4 Drive mounting	29
4.0 Serial ATA (SATA) interface	31
4.1 Hot-Plug compatibility	31
4.2 Serial ATA device plug connector pin definitions	32
4.3 Supported ATA commands	33
4.3.1 Identify Device command	35
4.3.2 Set Features command	39
4.3.3 S.M.A.R.T. commands	40
5.0 Seagate Technology support services	41
Index	43
A	43
C	43
D	43
E	43
F	43
G	43
H	43
I	43
K	44
L	44
M	44
N	44
O	44
P	44
Q	44
R	44
S	44
T	45
U	45
V	45

Match case Limit results 1 per page

SV35.2 Series Serial ATA Product Manual, Rev. D

2.9.5.2

Nonoperating shock

1 Disc models

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half-sine shock pulse

of 2 msec duration.

2, 3 and 4 Disc models

The nonoperating shock level that the drive can experience without incurring physical damage or degradation

in performance when subsequently put into operation is 300 Gs based on a nonrepetitive half-sine shock pulse

of 2 msec duration.

2.9.6

Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the

drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.9.6.1

Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards speci-

fied in this document are specified below.

2.9.6.2

Nonoperating vibration

The maximum nonoperating vibration levels that the drive may experience without incurring physical damage

or degradation in performance when subsequently put into operation are specified below.

5–22 Hz

0.02 inches (Limited displacement, peak to peak)

22–350 Hz

0.50 Gs

350–500 Hz

0.25 Gs

5–350 Hz

5.0 Gs

350–500 Hz

1.0 Gs