Home » Seagate Manuals » Hard Drives » Seagate ST3000DM001 » Manual Viewer

Seagate ST3000DM001 Barracuda 7200.9 PATA Product Manual - Page 36

Electromagnetic immunity, Reliability

View all Seagate ST3000DM001 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

2.11 Electromagnetic immunity When properly installed in a representative host system, the drive operates without errors or degradation in performance when subjected to the radio frequency (RF) environments defined in the following table: Table 15: Radio frequency environments Test Electrostatic discharge Radiated RF immunity Electrical fast transient Surge immunity Conducted RF immunity Voltage dips, interrupts Description Contact, HCP, VCP: ± 4 kV; Air: ± 8 kV 80 to 1,000 MHz, 3 V/m, 80% AM with 1 kHz sine 900 MHz, 3 V/m, 50% pulse modulation @ 200 Hz ± 1 kV on AC mains, ± 0.5 kV on external I/O ± 1 kV differential, ± 2 kV common, AC mains 150 kHz to 80 MHz, 3 Vrms, 80% AM with 1 kHz sine 0% open, 5 seconds 0% short, 5 seconds 40%, 0.10 seconds 70%, 0.01 seconds Performance level B A B B A C C C B Reference standard EN 61000-4-2: 95 EN 61000-4-3: 96 ENV 50204: 95 EN 61000-4-4: 95 EN 61000-4-5: 95 EN 61000-4-6: 97 EN 61000-4-11: 94 2.12 Reliability Nonrecoverable read errors Annualized Failure Rate (AFR) Contact start-stop cycles Warranty Preventive maintenance 1 per 1014 bits read, max. 0.34% (nominal power, 25°C ambient temperature) 50,000 cycles (at nominal voltage and temperature, with 60 cycles per hour and a 50% duty cycle) 5 years on distribution units. To determine the warranty for a specific drive, use a web browser to access the following web page: www.seagate.com/support/service/ From this page, click on the "Verify Your Warranty" link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The system will display the warranty information for your drive. None required. 30 Barracuda 7200.9 PATA Product Manual, Rev. F

Section	Page
1.0 Introduction 1	3
2.0 Drive specifications 3	3
2.1 Specification summary table 3	3
2.2 Formatted capacity 20	3
2.2.1 LBA mode 20	3
2.3 Default logical geometry 20	3
2.4 Recording and interface technology 21	3
2.5 Physical characteristics 22	3
2.6 Seek time 22	3
2.7 Start/stop times 22	3
2.8 Power specifications 23	3
2.8.1 Power consumption 23	3
2.8.2 Conducted noise 26	3
2.8.3 Voltage tolerance 26	3
2.8.4 Power-management modes 26	3
2.9 Environmental specifications 27	3
2.9.1 Ambient temperature 27	3
2.9.2 Temperature gradient 27	3
2.9.3 Humidity 27	3
2.9.4 Altitude 27	3
2.9.5 Shock 28	3
2.9.6 Vibration 28	3
2.10 Acoustics 29	3
2.11 Electromagnetic immunity 30	3
2.12 Reliability 31	3
2.13 Agency certification 31	3
2.13.1 Safety certification 31	3
2.13.2 Electromagnetic compatibility 31	3
2.13.3 FCC verification 32	3
2.14 Environmental protection 33	3
2.14.1 European Union Restriction of Hazardous Substances (RoHS) 33	3
2.15 Corrosive environment 33	3
3.0 Configuring and mounting the drive 35	3
3.1 Handling and static discharge precautions 35	3
3.2 Breather filter hole precautions 36	3
3.3 Jumper settings 37	3
3.3.1 Master/slave configuration 37	3
3.3.2 Cable-select option 37	3
3.3.3 Alternate capacity jumper 37	3
3.3.4 Ultra ATA/100 cable 38	3
3.4 Drive mounting 38	3
4.0 ATA interface 41	3
4.1 ATA interface signals and connector pins 41	3
4.1.1 Supported ATA commands 42	3
4.1.2 Identify Device command 44	3
4.1.3 Set Features command 48	3
4.1.4 S.M.A.R.T. commands 49	3
5.0 Seagate Technology support services 51	3
1.0 Introduction	7
2.0 Drive specifications	9
2.1 Specification summary table	9
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	28
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	29
2.8.1 Power consumption	29
2.8.1.1 Typical current profile	31
2.8.2 Conducted noise	32
2.8.3 Voltage tolerance	32
2.8.4 Power-management modes	32
2.9 Environmental specifications	33
2.9.1 Ambient temperature	33
2.9.2 Temperature gradient	33
2.9.3 Humidity	33
2.9.3.1 Relative humidity	33
2.9.3.2 Wet bulb temperature	33
2.9.4 Altitude	33
2.9.5 Shock	34
2.9.5.1 Operating shock	34
2.9.5.2 Nonoperating shock	34
2.9.6 Vibration	34
2.9.6.1 Operating vibration	34
2.9.6.2 Nonoperating vibration	34
2.10 Acoustics	35
2.11 Electromagnetic immunity	36
2.12 Reliability	36
2.13 Agency certification	37
2.13.1 Safety certification	37
2.13.2 Electromagnetic compatibility	37
2.13.3 FCC verification	38
2.14 Environmental protection	38
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	38
2.15 Corrosive environment	39
3.0 Configuring and mounting the drive	41
3.1 Handling and static discharge precautions	41
3.2 Breather filter hole precautions	42
3.3 Jumper settings	43
3.3.1 Master/slave configuration	43
3.3.2 Cable-select option	43
3.3.3 Alternate capacity jumper	43
3.3.4 Ultra ATA/100 cable	44
3.4 Drive mounting	44
4.0 ATA interface	47
4.1 ATA interface signals and connector pins	47
4.1.1 Supported ATA commands	48
4.1.2 Identify Device command	50
4.1.3 Set Features command	54
4.1.4 S.M.A.R.T. commands	55
5.0 Seagate Technology support services	57
Index	59
A	59
B	59
C	59
D	59
E	59
F	59
G	59
H	59
I	59
J	60
K	60
L	60
M	60
N	60
O	60
P	60
R	60
S	60
T	61
U	61
V	61