Home » Seagate Manuals » Hard Drives » Seagate ST3750330NS » Manual Viewer

Seagate ST3750330NS Barracuda ES.2 SATA Product Manual - Page 29

Serial ATA SATA interface

UPC - 836367003015

View all Seagate ST3750330NS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

4.0 Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA programmed input/output (PIO) modes 0-4; multiword DMA modes 0-2, and Ultra DMA modes 0-6. For detailed information about the Serial ATA interface, refer to the "Serial ATA: High Speed Serialized AT Attachment" specification. 4.1 Hot-Plug compatibility Barracuda ES.2 Serial ATA drives incorporate connectors which enable you to hot plug these drives in accordance with the Serial ATA II: Extension to Serial ATA 1.0a specification. This specification can be downloaded from www.serialata.org. Caution: The drive motor must come to a complete stop (Ready to spindle stop time indicated in Section 2.7) prior to changing the plane of operation. This time is required to insure data integrity. Barracuda ES.2 Serial ATA Product Manual, Rev. G 23

Section	Page
1.0 Introduction	7
1.1 About the Serial ATA interface	8
2.0 Drive specifications	9
2.1 Specification summary tables	9
2.2 Formatted capacity	14
2.2.1 LBA mode	14
2.3 Default logical geometry	14
2.4 Recording and interface technology	14
2.5 Physical characteristics	15
2.6 Seek time	15
2.7 Start/stop times	15
2.8 Power specifications	16
2.8.1 Power consumption	16
2.8.1.1 Typical current profiles	17
2.8.2 Conducted noise	18
2.8.3 Voltage tolerance	18
2.8.4 Power-management modes	18
2.9 Environmental specifications	19
2.9.1 Ambient temperature	19
2.9.2 Temperature gradient	19
2.9.3 Humidity	19
2.9.3.1 Relative humidity	19
2.9.3.2 Wet bulb temperature	19
2.9.4 Altitude	19
2.9.5 Shock	19
2.9.5.1 Operating shock	19
2.9.5.2 Nonoperating shock	19
2.9.6 Vibration	20
2.9.6.1 Operating vibration	20
2.9.6.2 Nonoperating vibration	20
2.10 Acoustics	21
2.11 Electromagnetic immunity	21
2.12 Reliability	22
2.12.1 Annualized Failure Rate (AFR) and Mean Time Between Failures (MTBF)	22
2.13 Agency certification	22
2.13.1 Safety certification	22
2.13.2 Electromagnetic compatibility	22
2.13.3 FCC verification	23
2.14 Environmental protection	24
2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive	24
2.14.2 China Restriction of Hazardous Substances (RoHS) Directive	24
2.15 Corrosive environment	24
3.0 Configuring and mounting the drive	25
3.1 Handling and static-discharge precautions	25
3.2 Configuring the drive	26
3.3 Serial ATA cables and connectors	26
3.4 Drive mounting	27
4.0 Serial ATA (SATA) interface	29
4.1 Hot-Plug compatibility	29
4.2 Serial ATA device plug connector pin definitions	30
4.3 Supported ATA commands	31
4.3.1 Identify Device command	33
4.3.2 Set Features command	37
4.3.3 S.M.A.R.T. commands	38
5.0 Seagate Technology support services	39
Index	41
A	41
B	41
C	41
D	41
E	41
F	41
G	41
H	41
I	42
K	42
L	42
M	42
N	42
O	42
P	42
Q	42
R	42
S	43
T	43
U	43
V	43

Match case Limit results 1 per page

Barracuda ES.2 Serial ATA Product Manual, Rev. G

4.0

Serial ATA (SATA) interface

These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA

programmed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6.

For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT

Attachment” specification.

4.1

Hot-Plug compatibility

Barracuda ES.2 Serial ATA drives incorporate connectors which enable you to hot plug these drives in accor-

dance with the Serial ATA II: Extension to Serial ATA 1.0a specification. This specification can be downloaded

from www.serialata.org.

Caution:

The drive motor must come to a complete stop

(Ready to spindle stop time indicated in Section 2.7)

prior to changing the plane of operation. This time is required to insure data integrity.