Home » Seagate Manuals » Hard Drives » Seagate ST39175LW » Manual Viewer

Seagate ST39175LW Product Manual - Page 7

List of s - barracuda

Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

List of Figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Typical 5V startup and operation current profile 23 Typical 12V startup and operation current profile 23 Breather filter hole location 34 Master/slave jumper settings 35 Ultra ATA cable connectors 36 Mounting dimensions-top, side and end view 37 I/O pins and supported ATA signals 39 Barracuda 7200.9 PATA Product Manual, Rev. C v

Section	Page
1.0 Introduction	9
2.0 Drive specifications	11
2.1 Specification summary table	11
2.2 Formatted capacity	26
2.2.1 LBA mode	26
2.3 Default logical geometry	26
2.4 Recording and interface technology	27
2.5 Physical characteristics	28
2.6 Seek time	28
2.7 Start/stop times	28
2.8 Power specifications	29
2.8.1 Power consumption	29
2.8.1.1 Typical current profile	31
2.8.2 Conducted noise	32
2.8.3 Voltage tolerance	32
2.8.4 Power-management modes	32
2.9 Environmental specifications	33
2.9.1 Ambient temperature	33
2.9.2 Temperature gradient	33
2.9.3 Humidity	33
2.9.3.1 Relative humidity	33
2.9.3.2 Wet bulb temperature	33
2.9.4 Altitude	33
2.9.5 Shock	34
2.9.5.1 Operating shock	34
2.9.5.2 Nonoperating shock	34
2.9.6 Vibration	34
2.9.6.1 Operating vibration	34
2.9.6.2 Nonoperating vibration	34
2.10 Acoustics	35
2.11 Electromagnetic immunity	36
2.12 Reliability	37
2.13 Agency certification	37
2.13.1 Safety certification	37
2.13.2 Electromagnetic compatibility	37
2.13.3 FCC verification	38
2.14 Environmental protection	39
2.14.1 European Union Restriction of Hazardous Substances (RoHS)	39
2.15 Corrosive environment	39
3.0 Configuring and mounting the drive	41
3.1 Handling and static discharge precautions	41
3.2 Breather filter hole precautions	42
3.3 Jumper settings	43
3.3.1 Master/slave configuration	43
3.3.2 Cable-select option	43
3.3.3 Alternate capacity jumper	43
3.3.4 Ultra ATA/100 cable	44
3.4 Drive mounting	44
4.0 ATA interface	47
4.1 ATA interface signals and connector pins	47
4.1.1 Supported ATA commands	48
4.1.2 Identify Device command	50
4.1.3 Set Features command	54
4.1.4 S.M.A.R.T. commands	55
5.0 Seagate Technology support services	57
Index	63
A	63
B	63
C	63
D	63
E	63
F	63
G	63
H	63
I	63
J	64
K	64
L	64
M	64
N	64
O	64
P	64
R	64
S	65
T	65
U	65
V	65

Match case Limit results 1 per page

Barracuda 7200.9 PATA Product Manual, Rev. C

List of Figures

Figure 1.

Typical 5V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 2.

Typical 12V startup and operation current profile. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 3.

Breather filter hole location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Figure 4.

Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Figure 5.

Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Figure 6.

Mounting dimensions—top, side and end view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Figure 7.

I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39