Sharp 21SFX10L Service Manual - Page 29

Description Of Schematic Diagram, E

Get Sharp 21SFX10L PDF manuals and user guides View all Sharp 21SFX10L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

CHAPTER T2SME1VeaSrrvk-iFecXet 1M0aLnual 9. DESCRIPTION OF SCHEMATIC DIAGRAM 21S-FX10L DESCRIPTION OF SCHEMATIC DIAGRAM NOTES: 1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ) 2. All resistors are 1/16 watt, unless otherwise noted. 3. All capacitors are μF, unless otherwise noted. (P=pF=μμF) 4. (G) indicates ±2% tolerance may be used. 5. indicates line isolated ground. VOLTAGE MEASUREMENT CONDITIONS: 1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 120V AC and all controls set for normal picture unless otherwise indicated. 2. All voltages measured with 1000μ V B & W or Color signal. WAVEFORM MEASUREMENT CONDITIONS: 1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control. 2. indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.) AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS. MARK= X-RAY RELATED PARTS. DRGANNES MARQUES ET HACHRES ( ): PIECES RELATIVES A LA SECURITE. MARQUE : PIECS RELATIVE AUX RAYONS X. This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice. 9 - 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
21S-FX10L
9 – 1
TV
21S-FX10L
Service Manual
21S-FX10L
Market
E
CHAPTER 9.
DESCRIPTION OF SCHEMATIC DIAGRAM
DESCRIPTION OF SCHEMATIC DIAGRAM
NOTES:
1. The unit of resistance "ohm" is omitted.
(K=k
Ω
=1000
Ω
, M=M
Ω
)
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are
μ
F, unless otherwise noted.
(P=pF=
μμ
F)
4. (G) indicates
±
2% tolerance may be used.
5.
indicates line isolated ground.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000
μ
V B & W or Color
signal.
WAVEFORM MEASUREMENT CONDITIONS:
1.
Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
AND SHADED (
) COMPONENTS
=
SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES
ET HACHRES (
):
PIECES RELATIVES A LA SECURITE.
MARQUE
:PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
±
±