Sharp AR-162 Service Manual - Page 6

] Maintenance - parts

Get Sharp AR-162 PDF manuals and user guides View all Sharp AR-162 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

[6] MAINTENANCE 1.Maintenance table X : Check (Clean, adjust, or replace when required.) O : Clean : Replace Unit name Part name When calling or replacing the kit Transfer section Charger unit O Transfer paper guide O Optical section Lamp unit Reflector O Mirror O No. 2/3 mirror unit Mirror O Pulley X CCD peripheral Lens O Glass Table glass O White plate O Other Drive wire X Rail X Document cover O Document size sensor O LSU Dust-proof glass O Paper feed section Multi paper feed Takeup roller O section Paper feed roller O Spring clutch O Cassette section Paper feed roller O Spring clutch O Paper transport section Fusing section PS roller O Transport (paper exit) rollers O Spring clutch O Upper heat roller O Pressure roller O Pressure roller bearing X Upper separation pawl X Lower separation pawl X Drive section Gears X Belts X Paper exit section Ozone filter X *1: Recommendable replacement time: 30K (A4 (8.5" x 11"), 6% print) : Adjust : Lubricate 150k O O O O O X O O O X X O O O O O O O O O O O O O O O X O X *1 2. Maintenance display system Toner Life Remaining quantity check *1 Developer Remaining quantity LED Machine Life LED Machine Maintenance LED Machine 13K a. Press and hold the density adjustment LIGHT key for more than 5 sec, and the machine will enter the user program mode. b. Press and hold the "%" key for more than 5 sec, and the remaining quantity will be displayed on the copy quantity display in one of the following levels: (Remaining quantity display levels: 100%, 75%, 50%, 25%, 10%, LO) c. Press the density adjustment LIGHT key to cancel. NEAR EMPTY About 10% EMPTY ON Flash Operation allowed Stop 30K ON at 30K of the developer count. Selection is available between Not Stop and Stop by Service Simulation (SIM 26-37) Setup. (If Stop is selected, the LED will flash and stop at 30K.) *Default: Not Stop *Clear: SIM 42-1 Selection is available among 30K, 15K, 10K, 7.5K, 5K, and free (no lighting) with SIM 21-1. *Default: 30K *Clear: SIM 20-1 Not stop. *1:Installation of a new toner cartridge allows to display the remaining quantity. AR-162S SPECIFICATIONS 3-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
AR-162S SPECIFICATIONS 3-5
[6] MAINTENANCE
1.Maintenance table
X : Check (Clean, adjust, or replace when required.)
O : Clean
: Replace
: Adjust
: Lubricate
*1: Recommendable replacement time: 30K (A4 (8.5" x 11"), 6% print)
2. Maintenance display system
*1:Installation of a new toner cartridge allows to display the remaining quantity.
Unit name
Part name
When calling or replacing
the kit
150k
Transfer section
Charger unit
O
O
Transfer paper guide
O
O
Optical section
Lamp unit
Reflector
O
O
Mirror
O
O
No. 2/3 mirror unit
Mirror
O
O
Pulley
X
X
CCD peripheral
Lens
O
O
Glass
Table glass
O
O
White plate
O
O
Other
Drive wire
X
X
Rail
X
X
Document cover
O
O
Document size sensor
O
O
LSU
Dust-proof glass
O
O
Paper feed section
Multi paper feed
section
Takeup roller
O
O
Paper feed roller
O
O
Spring clutch
O
O
Cassette section
Paper feed roller
O
O
Spring clutch
O
O
Paper transport section
PS roller
O
O
Transport (paper exit) rollers
O
O
Spring clutch
O
O
Fusing section
Upper heat roller
O
Pressure roller
O
O
Pressure roller bearing
X
O
Upper separation pawl
X
O
Lower separation pawl
X
O
Drive section
Gears
X
X
Belts
X
O
Paper exit section
Ozone filter
X
X *1
Toner
Life
13K
Remaining quantity check *1
a.
Press and hold the density adjustment LIGHT key for more than 5 sec, and the machine will enter
the user program mode.
b.
Press and hold the "%" key for more than 5 sec, and the remaining quantity will be displayed on
the copy quantity display in one of the following levels:
(Remaining quantity display levels: 100%, 75%, 50%, 25%, 10%, LO)
c.
Press the density adjustment LIGHT key to cancel.
Remaining quantity
NEAR EMPTY About 10%
EMPTY
LED
ON
Flash
Machine
Operation allowed
Stop
Developer
Life
30K
LED
ON at 30K of the developer count.
Machine
Selection is available between Not Stop and Stop by Service Simulation (SIM 26-37) Setup.
(If Stop is selected, the LED will flash and stop at 30K.)
*Default: Not Stop
*Clear: SIM 42-1
Maintenance
LED
Selection is available among 30K, 15K, 10K, 7.5K, 5K, and free (no lighting) with SIM 21-1.
*Default: 30K
*Clear: SIM 20-1
Machine
Not stop.