Sharp AR-M280 AR-M280 AR-M350 AR-M450 Operation Manual (for multifunction
Sharp AR-M280 Manual
View all Sharp AR-M280 manuals
Add to My Manuals
Save this manual to your list of manuals |
Sharp AR-M280 manual content summary:
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 1
LASER PRINTER (Multi-function printer) Operation Manual for printer operation and general information on multi functions - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 2
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 3
required space around the machine for servicing and proper ventilation. A small amount of ozone is produced within the copier 23-5/8" (60cm) 11-13/16 weighted average concentration. However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 4
not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty printouts. Driver's licenses Fusing unit Adjuster Lock Release "BATTERY DISPOSAL" CONTAINS MANGANESE DIOXIDE LITHIUM BATTERY. MUST BE DISPOSED OF PROPERLY. CONTACT YOUR SHARP DEALER OR SERVICER FOR INSTRUCTIONS - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 5
to gain access to the inside of the product. Refer all servicing to qualified personnel. For North America: SAFETY PRECAUTIONS This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that the equipment does - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 6
CAUTIONS For Europe: CLASS 1 LASER PRODUCT LASER KLASSE 1 LUOKAN 1 LASERLAITE KLASS 1 LASERAPPARAT CAUTION INVISIBLE LASER RADIATION WHEN OPEN INTERLOCKS DEFEATED. AVOID EXPOSURE TO BEAM. VORSICHT UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET UND SICHERHEITSVERRIEGELUNG ÜBERBRÜCKT. NICHT DEM - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 7
of use of the facsimile feature, see the facsimile operation manual supplied with the facsimile expansion kit. s Line connection For the telephone line. Line connector TEL LINE s Fax power switch When using this product as a facsimile, keep always the fax power switch on that is located on the - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 8
SOFTWARE FOR WINDOWS INSTALLING PRINTER DRIVERS AND PRINTER UTILITIES REMOVING PRINTER DRIVERS AND PRINTER UTILITIES INSTALLING PRINTER DRIVERS USING THE PLUG & PLAY FUNCTION OR ADD PRINTER WIZARD q Before installation SETTING THE PRINTER DRIVER q Setting print conditions under Windows - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 9
q Setting the printer driver for your purpose q Setting the copier for your purpose q Troubleshooting MAIL-BIN STACKER q Part names and functions removal and staple cartridge replacement q Misfeed removal in the finisher q Troubleshooting SADDLE STITCH FINISHER q Part names and functions - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 10
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 11
using this product. Page INTRODUCTION 1-2 MAIN FEATURES 1-5 PART NAMES AND FUNCTIONS 1-6 G Exterior 1-6 G Interior 1-7 G Part names and functions of peripheral units 1-8 G Operation & 2000 sheet paper drawer ....... 1-24 G Specifications 1-24 ADDING TONER 1-25 STORAGE OF SUPPLIES 1-25 1-1 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 12
AR-P350 35 pages/minute printer AR-P450 45 pages/minute printer AR-M350 35 pages/minute printer (with a multi-function controller board)*1 AR-M450 45 pages/minute printer (with a multi-function controller board)*1 DM-3500 35 pages/minute printer DM-3501 35 pages/minute network printer - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 13
the copier feature and facsimile feature. In the touch panel messages in the scanner module, the "scanner module" is displayed as "document feeder". G To use a scanned image as image data on a computer, a network scanner expansion kit (peripheral unit) is needed in addition to the network printer - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 14
Punch module Multi-function controller board Print server card PS3 expansion kit Network scanner expansion kit Facsimile expansion kit Additional fax memory (8 MB) Power supply unit Hard disk drive Common to all features Manual paper feeding Print onto special paper Two-sided print Touch panel - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 15
printer that can be used as a local printer and a network printer as well as a copier, a network ENERGY STAR® Partner, SHARP has determined that this mode, the fuser is maintained at a lower heat level thereby saving power. Auto power shut-off mode The machine will enter the auto power shut-off mode - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 16
NAMES AND FUNCTIONS Exterior Bypass tray (part of duplex module/bypass tray)*1 Exit tray*1 x 17" and 8-1/2" x 14" (A3 and A4). Operation panel (See page xxxx.) Front cover Open to add toner and remove misfeeds. Main switch (See page xxxx.) Press to turn power on and off. Paper tray 1 Stand/3 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 17
Interior PART NAMES AND FUNCTIONS 1 Duplex drum. NOTE Do not touch or damage the photoconductive drum. Cartridge lock lever When replacing the drum, toner or developer cartridge, turn down this lever and pull it out. *2 For replacement and installation of each cartridge, see the separate manual - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 18
PART NAMES AND FUNCTIONS Part names and functions of peripheral units 1-8 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 19
in the printer driver. The bins can be classified by persons or by sections depending on users so that the users deliver their printed sheets to their specified bin. Sorted output separated from the other users, therefore, can be performed. Output sheets in the copy and fax modes are deposited - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 20
printer as a network printer. G Multi-function controller board Printer controller required for using the copier, facsimile, and network scanner features. G PS3 expansion kit Kit required for using the printer as a PostScript compatible printer. (for PostScript level 3) G Hard disk drive Extends - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 21
the printer current state. [i] displayed in messages indicates the [INFORMATIONS] key. [ERROR] indicator Lights up when paper or toner must [BACK/C] key is pressed while the operation procedure is displayed, the information mode will be canceled. If you press and hold down this key while printing - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 22
is warming up to allow printing. READY. The printer is ready to print. FROM TRAY # The printer is currently executing printing. CHANGE THE TONER CARTRIDGE. PAPER JAM. Toner runs out. Replace the toner cartridge. (See page xxxx.) A misfeed has occurred. (See page xxxx.) ADD PAPER. Paper - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 23
will resume. 1 G To delete print data of a reserved job (that waits for printing): Print data transmitted from computers will be stored in this printer (up to 99 jobs) and will be output sequentially.To delete print data of a reserved job before starting printing, press the [ ] or [ ] key - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 24
PART NAMES AND FUNCTIONS When the printer is equipped with a scanner module as a peripheral unit, use the Press to switch the display to the network scan/fax mode. (See page xxxx of the facsimile operation manual.) [COPY] key Press to switch the display to the copy mode. (See page xxxx.) 1-14 [JOB - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 25
, the list of stored print data is displayed here (up to 100 jobs). The job retention function can be used only if the printer is equipped with a hard disk drive as a peripheral unit. [Display switching] keys Use to switch the page of the print hold job list. If the list is not contained - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 26
PART NAMES AND FUNCTIONS Job status screen (common to print, copy, network scan, and fax modes) This screen is displayed when the [JOB STATUS] key on the operation panel is pressed. A job list which indicates the current job and reserved jobs - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 27
PART NAMES by a key operator program. (See page xxxx of the Key Operator's guide.) The touch panel (display) illustrated in this operation panel is a conceptual . [Example 2] DUAL PAGE COPY MULTI SHOT When using the copier feature or the facsimile feature, the functions shown below which can - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 28
paper. Doing so may cause a misfeed. G Use SHARP standard paper for paper tray 1. (See page xxxx.) G Do not place a heavy object or press down hard on a tray when the tray is pulled out. Loading guide plates A and B are slidable. Adjust them to the paper size to be loaded while squeezing their lock - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 29
not proper, a paper misfeed or oblique feeding may occur. I Paper that can be used G SHARP standard paper G Ordinary paper other than SHARP standard paper Paper size 5-1/2" x 8-1/2" or A5 (105 x 148 mm) Paper weight: Continuous feeding 15 lbs.(52 g/m2) *1 Single sheet feeding 15 lbs.(52 g/m2) 11 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 30
LOADING PAPER Method of setting paper size and type When the paper size or type is changed in a paper tray, set them referring to the following procedure. When using the operation panel on the main unit: For setting paper size and type from the operation panel with touch panel, see the next page. - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 31
LOADING PAPER When using the operation panel with touch panel: 1 Press the [CUSTOM SETTINGS] key. The custom setting menu screen will appear. 5 Touch the [OK] key to complete the setting. TOTAL COUNT 1 TRAY SETTINGS 2 Press the [TRAY SETTINGS] key. TOTAL COUNT The paper tray selection screen - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 32
printer with a ribbon cassette, particularly, may cause printed characters to come off or may cause smudges on printouts. Example of setting postcards Be sure to set the postcards face down and the upper part closures, windows, linings size Paper capacity Dimensions Weight Multi purpose drawer Max. - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 33
Paper capacity (ordinary paper) Dimensions Weight Stand/3 x 500 sheet paper drawer Upper tray: Max. 11" x 17" (A3), min. 5-1/2" x 8-1/2"R (A5R), Middle/ lower trays: Max. 11" x 17" (A3), min. 7-1/4" x 10-1/2"R (B5R) 15 lbs. - 28 lbs. (56 - 105 g/m2) 500 sheets (20 lbs. (80 g/m2)) each 23-1/32 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 34
Gently push the large capacity paper tray into the printer. Push the tray firmly all the way into the printer. 3 Load paper onto the right and left paper (page xx). Specifications Name Paper sizes Paper weight Paper capacity (ordinary paper) Dimensions Weight 1-24 6 Loading of paper in the stand/ - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 35
a message indicating need to replace the toner cartridge will appear. Also depending on the model, a message indicating need to replace the developer cartridge may appear. For the procedure of replacement of these cartridges, see the separate manual "Supply Replacement Method." 1 STORAGE OF SUPPLIES - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 36
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 37
allows print start operation from the operation panel of the printer. Page CONNECTING TO A COMPUTER 2-2 SOFTWARE FOR WINDOWS 2-2 INSTALLING PRINTER DRIVERS AND PRINTER UTILITIES 2-3 REMOVING PRINTER DRIVERS AND PRINTER UTILITIES 2-3 INSTALLING PRINTER DRIVERS USING THE PLUG & PLAY FEATURE OR ADD - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 38
(PCL5e and PCL6) G Optional PostScript printer driver (compatible to PostScript level 3) and SHARP AR-xxxx PPD file (PostScript Printer Description file) I Printer utilities G Printer Administration Utility G Printer Status Monitor G Display Font 1. Printer drivers A printer driver is software - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 39
DRIVERS AND PRINTER UTILITIES Windows client Printer Status Monitor Windows software PCL printer drivers Display font Network administrator Network Administration Utility The following software can be installed from the installer supplied in the CD-ROM : G PCL printer drivers (PCL5e and PCL6 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 40
\9x_pcl6 Path for using PCL5e driver under Windows NT R:\AR-Tigeokamptor\Option\English\Nt_pcl5e Path for using PCL6 driver under Windows NT R:\AR-Tigeokamptor\Option\English\Nt_pcl6 I Example of installation of a printer driver using the Add Printer wizard under Windows 98 The installation method - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 41
Printers]. The Printer window will appear. 2 Right-click the installed printer driver and select [Properties]. This example is the screen displayed by selecting AR-P350PCL5e. 2 Right-click the installed printer driver and select [Document Defaults network printer and you have installed the Printer - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 42
clicked, the help screen for description of various function settings that can be operated remotely from the Web pages for this product through the network will appear. For the setting of each function, see this detailed description. 1 Open the Web browser on your computer. 2 Input the IP Address - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 43
network scanner tool/Sharpdesk has been installed and file types as well as the information for destination control (destination name, index, name for front panel display, etc.) are set. I Setting of Fax Destination Control Sets the fax destination. Fax numbers of recipients and communication mode - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 44
below. I Network Card Setup A link to the network card Web page for setting the print server card (network interface card) is provided. I Password Setup A password for accessing the Web pages is set. Two types of password (user level and administrator level) are set. I Network Scanning Setup Basic - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 45
step 8 on page xx.) If a password is set in the printer driver setting, password entry is needed to start printing of a holdThis mode can increase the security of hold jobs.his mode can increase the security o hd jobs. G Password in the Hold After Print mode: Password entry on the operation panel - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 46
is pressed, a user name and a file name of print data stored in the printer as a hold job will appear. 3 Select the desired data. Press the or data is displayed. 4 Press the [OK] key. 2-10 6 Use the same procedure as step 5 to enter the password from the fourth digit to the first digit and then - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 47
panel: 1 Press the [PRINT] key to display the printer basic screen. 4 Select execution of printing, cancellation of printing password. (needed only if a password has been set) ENTER PIN VIA THE 10-KEY. CANCEL Be sure to enter the password that has been entered on the computer. If no password - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 48
PRINT START OPERATION FROMTHE OPERATION PANEL Printer account control If the key operator program "Auditing mode" is set, the number of screen of the printer driver.The account number entry screen will be displayed by clicking "Job control" in the "Main" tab of the printer driver. When an invalid - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 49
conditions. Page MAKING CONFIGURATION SETTING 3-2 G Operation procedure common to all printer configuration settings (items that can be set from the operation panel 3-2 G Main program settings 3-4 G PCL settings 3-4 G PostScript settings 3-4 CUSTOM SETTINGS 3-5 G Operation procedure common to - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 50
settings to be made. The items set with the printer configuration settings are shown below. G Main program settings Basic settings used in printing (See page xxxx.) G PCL settings Sets a PCL symbol set. (See page xxxx.) G PostScript settings*1 Sets whether a PostScript error page is printed - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 51
and any job currently transmitted to the printer will be printed in the former print conditions. 2 Touch the key of the desired item to display its setting screen. 3 CONDITION SETTINGS MAIN PROGRAM SETTINGS PostScript SETTINGS PCL SETTINGS For details of each setting item, see the description - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 52
printer driver, perform setting in the printer driver. I Smoothing SMOOTHING reduces jaggies seen at roundish curved portions of characters and images to be printed and improves pseudo resolution. Default unless otherwise specified by application software. Default setting: Depends on installation of - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 53
of the built-in clock of the printer are set. G Tray settings*4 mode*2 The fax receive mode (automatic or manual) is set. 3 G Fax data forward*2 Received fax . For settings, see Key Operator's Guide. (See page xxxx.) 1 Can and the facsimile feature or the network scanner feature can be used. - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 54
screen. Any print jobs held in the printer and any job currently transmitted to the printer will be printed in the former custom setting CUSTOM SETTINGS TOTAL COUNT TRAY SETTINGS DISPLAY ADDRESS LIST PRINT RECEIVE MODE CLOCK FAX DATA KEY OPERATOR PROGRAMS To set another item, repeat steps 2 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 55
the PCL printer drivers is printed. G PCL symbol set printing: A PCL symbol set list is printed. G NIC page printing: A list of settings used by the NIC (Network Interface in the copy mode (see page xxxx), timer operations in the fax mode (see page xxxx), and date and time information recording of - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 56
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 57
CHAPTER 4 TROUBLESHOOTING AND MAINTENANCE This chapter describes misfeed removal, user maintenance, etc. Page MISFEED REMOVAL the transport area, fusing area, and exit area 4-6 q Misfeed in the duplex module 4-7 TROUBLESHOOTING 4-8 USER MAINTENANCE 4-12 q Cleaning the scanner module 4-12 4-1 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 58
will appear and printing will stop. Follow the procedure below to remove misfed paper. PAPER JAM. NOTES q Do not damage or touch the photoconductive drum. (See page 1-6.) q Be careful not to tear the misfed paper during removal. q If paper is accidentally torn during removal, be sure to remove all - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 59
originals may disturb scanning, resulting in partially improper copies or images for facsimile or scanner transmission. NOTES q Do not damage or touch the photoconductive drum. (See page 1-6.) q Be careful not to tear the misfed paper during removal. q If paper is accidentally torn during removal - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 60
may be misfed between the paper tray and the paper feed area in the printer. Before pulling out the paper tray, be sure to open the left side tray, see the illustration below.) NOTE Since paper may be misfed in the inner part, check carefully and remove it. 3 If misfed paper is not found in step - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 61
) and remove the misfed paper. NOTE Since paper may be misfed in the inner part, check carefully and remove it. 4 q If paper is misfed on the right If paper is misfed on the left paper feed table: Raise the paper guide and remove the misfed paper. 4 Gently close the large capacity tray. Push - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 62
MISFEED REMOVAL Misfeed in the transport area, fusing area, and exit area CAUTION The fusing unit is hot. Take care in removing paper. (Do not touch the metal portion.) 1 Pull out the duplex module. Hold the knob and gently open the module. If the machine is not equipped with the duplex module, - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 63
tray up, remove the misfed paper. q If paper is misfed at the upper part of the duplex module: Gently remove the misfed paper taking care not to tear the to clear the misfeed message. q If paper is misfed at the lower part of the duplex module: Gently remove the misfed paper taking care not to - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 64
specific instructions, check the list below. This section describes only troubleshooting concerning the printer feature and problems common to all features of this product. For troubleshooting of the copier, facsimile, and network scanner features, see the respective manuals. Also for problems in - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 65
TROUBLESHOOTING Problem Black pages Image loss along the edges Printer prints in reverse order. Solution q Is color image data printed? Color image may be printed in black. q Are the black and white areas reversed? Cancel negative image printing feature in the printer driver. q Is the image - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 66
TROUBLESHOOTING Problem function. (A notice page is printed.) Password entry is requested. Solution q Is a load it again. q Is paper size or weight out of the allowable range? Use paper in Password set in the retention function? Password is needed when executing printing. If the password - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 67
orientation. If the orientation is changed in the middle of a print job, part of images may not be printed. Image rotation will not occur in the driver for Windows NT 4.0, the printer resident fonts cannot be specified. Font downloading, therefore, is performed each time printing is executed. 10 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 68
not use thinner, benzene, or similar volatile cleaning agents. Cleaning the scanner module If the document glass, cover or original scanning portion of the scanner module is dirty, scanned image may be soiled or black stripes may appear on image. Keep them always clean. Wipe them with a soft, clean - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 69
printer driver 5-7 G Misfeed in the mail-bin stacker 5-8 FINISHER 5-9 G Part names 5-9 G Specifications 5-9 G Finisher functions 5-10 G Using the finisher functions 5-11 G Staple cartridge replacement and staple jam removal 5-12 G Misfeed in the finisher 5-14 G Troubleshooting (concerning - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 70
module/bypass tray. For misfeed removal of the duplex module, see page xxx. Part names Exit tray The tray is extendable. To print onto large paper (8-1/2" x Max. 11" x 17" or A3, Min. 5-1/2" x 8-1/2"R or A5R Paper weight 15 to 28 lbs. or 56 to 105 g/m2 Reference paper position Center Bypass - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 71
guides again properly. If there is a clearance, paper may be fed obliquely or may be curled. G When using plain paper other than SHARP recommended paper or special paper other than 5 postcards and SHARP by a facsimile for plain paper or by another printer. Doing so may cause smudges on printouts. G - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 72
"Properties" on the printer driver setting screen. The screens used in the following descriptions are for a PCL driver in the Windows 98 environment. I Using the exit tray If you touch the [OUTPUT] key on the copy mode basic screen, a selection screen for output will appear. Select the exit tray - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 73
DUPLEX MODULE Troubleshooting (concerning the duplex module) Check the list below before contacting the SHARP Service Center. Problem The printer does not print. Printed images onto paper from the bypass tray are inclined. A paper misfeed occurs in the bypass tray. Solution Message indicating - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 74
paper in the copy mode and the fax mode can be delivered to the top tray other than mail bins. (Output paper from the printer feature can also be delivered to the top tray.) Part names Top cover Open for misfeed removal. Top tray Output paper from the printer, copier, and facsimile features can - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 75
tab and select a mail bin for delivery at "Output". (The top tray can be selected.) The illustration below shows the screen for a PCL printer driver in the Windows 98 environment. NOTES G For the settings above, installation of peripheral units must have been set properly in the properties of the - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 76
on the top cover to close it. 3 If the misfed paper is not found in step 2, open the front cover. 7 Close the paper guide. Close the paper guide securely to its original position. 8 Close the front cover. 4 Turn the roller rotating knob in the direction of the arrow to remove the misfed - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 77
Part names Knob Hold this knob to open the finisher for misfeed removal. Top cover Open for misfeed removal. Top tray Paper output from the printer, copier, and fax capacity Stapling position Reference paper position Power supply Dimensions Weight Finisher 2 Print face down Top tray: normal tray - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 78
.) When the staple sort function is selected, the offset function will not operate. I Staple sort mode Collated sets of printouts are stapled and delivered to the offset tray. The stapling positions, orientation, paper x 11", A4 and B5 Stapling capacity: Up to 30 sheets for any available sizes 5-10 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 79
Staple". The illustration below shows the screen for a PCL printer driver in the Windows 98 environment. NOTES G For the settings above, printer driver help. The details of the functions are described. I Using the finisher functions in the copy mode If you touch the [OUTPUT] key on the copy mode - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 80
that of the staple box. 9 Close the front cover. NOTE Execute test printing in the staple sort mode to ensure that stapling is performed properly. Staple cartridge replacement is now complete. Following steps 10 to 14 are the procedure for staple jam removal. These steps are not needed for staple - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 81
10 Remove the paper from the stapler compiler. 11 Raise the lever at the end of the staple box. If the top staple lever and return the staple unit to face down. 15 Close the front cover. NOTE Execute test printing in the staple sort mode to ensure that stapling is performed properly. FINISHER 5 5-13 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 82
. 1 Remove the misfed paper from the stapler compiler. Be careful not to tear the misfed paper during removal. 6 Open the paper guide and remove the misfed paper. Paper guide Be careful not to tear the misfed paper during removal. 2 Open the top cover. Top cover Move the tab in the direction - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 83
FINISHER Troubleshooting (concerning the finisher) Check the list below before contacting the SHARP Service Center. Problem Stapling position is front Close all covers. (See pages xx and xx.) cover or paper guide of the finisher open? Message indicating need to remove paper Remove all paper from - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 84
FINISHER Stapling position quick reference list When stapling is performed, the orientation of image data or original is related to the stapling position, binding position and orientation of paper complicatedly. The table below shows the relation. Image data or original First page (front side) - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 85
is installed as a peripheral unit. Part names Stapler compiler Paper to be stapled cartridge or to remove jammed staples. Front cover Open to replace the staple cartridge Paper size Paper weight Paper type Paper g/m2 Lower tray: 17 to 34 lbs. or 64 to 128 g/m2 Upper tray:same as the specifications - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 86
SADDLE STITCH FINISHER Name Stapling position Reference paper position Power supply Dimensions Weight Saddle stitch finisher Upper tray: two types (one at rear, one at front) Lower tray: 4-47/64" (120 mm) pitch from the center of paper Center Drawn from the power supply unit (peripheral unit)(See - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 87
SADDLE STITCH FINISHER I Staple sort mode Collated sets of printouts are stapled and delivered to the offset tray. Alternatively, printed paper is stapled at the center and delivered to the lower - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 88
illustration below shows the screen for a PCL printer driver in the Windows 98 environment. I Using the punch printer driver help. The details of the functions are described. I Using the finisher functions in the copy mode If you touch the [OUTPUT] key on the copy mode part of the main unit. - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 89
, the pamphlet copy function (see page xx of the copier operation manual) will be automatically set. [PUNCH] key (See page cartridge cannot be removed. 6Insert a new staple cartridge into the staple box. After inserting the staple cartridge, press down on the staple box cover to lock the cartridge - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 90
the staple box. Push the staple box until it clicks into place. 10Close the front cover. NOTE Execute test printing in the staple sort mode to ensure that stapling is performed properly. 9Push back the stapler section. I Staple jam removal 1Open the front cover. 5Remove the misfed paper. 2Turn - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 91
11Return the lever to its original position. 13Push back the stapler section. 14Close the front cover. NOTE Execute test printing in the staple sort mode to ensure that stapling is performed properly. 5 I Punch scrap disposal 1Pull the knob and slide the saddle stitch finisher away from the main - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 92
SADDLE STITCH FINISHER Misfeed in the saddle stitch finisher If a misfeed has occurred in the saddle stitch finisher during printing, remove the misfed paper following the procedure below. 1Pull the knob and slide the saddle stitch finisher away from the main unit. 6Close the top cover. - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 93
11Remove the misfed paper. Be careful not to tear the misfed paper during removal. 12Turn roller rotating knob D in the direction of the arrow. Roller rotating knob D 13Turn roller rotating knob D in the direction of the arrow. Be careful not to tear the misfed paper during removal. 14Close the - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 94
FINISHER Troubleshooting (concerning the saddle stitch finisher) Check the list below before contacting the SHARP Service Center. Problem on page xx. Remove jammed staples. (See page xx.) Replace the staple cartridge. (See page xx.) Stapling cannot be performed onto different size paper. Paper - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 95
SADDLE STITCH FINISHER Stapling position quick reference list When stapling is performed, the orientation of image data or original is related to the stapling position, binding position, and orientation of paper complicatedly. The table below shows the relation. Image data or original First page - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 96
SADDLE STITCH FINISHER Relation between print image and saddle stitch When saddle stitch is performed, the orientation of image data or original is related to the orientation of paper complicatedly. The table below shows the requirements of the image and the saddle stitch. Image data or original - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 97
CHAPTER 6 KEY OPERATOR PROGRAMS This chapter describes operation of the key operator programs for use by the key operator. Please read this chapter thoroughly for proper use of these programs. Page KEY OPERATOR PROGRAMS 6-2 G Key operator program list 6-2 G Using the key operator programs 6-3 G - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 98
operator programs specific to the copier feature, facsimile feature, and network scanner feature, see the respective operation manuals.The key operator programs can Energy save Auto power shut-off timer Preheat mode Toner save {Toner save in printer mode} Auto power shut-off Operation panel settings - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 99
] key is pressed, the message shown to the left will appear. 3Enter the fifth digit of the password and press the [OK] key. KEY OPERATOR CODE O For the factory default setting of the key operator code number (password), see page xxxx. If you press the [OK] key to register the fifth digit after - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 100
"*" will be added to the message. The display in ( ) shows the factory default setting. Key operator code entry [OK] [BACK/C] AUDITOR SETTINGS [OK] [BACK/C] OFF TIMER (30 min.*) AUTO POWER SHUT-OFF (ENABLE*) PREHEAT MODE (15 min.*) TONER SAVE (OFF*) OPERATION PANEL SETTINGS [OK] [BACK/C] AUTO - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 101
AUTO SELECT (OFF*) [OK] [BACK/C] HEXADECIMAL DUMP MODE (OFF*) PDL FOR PARALLEL PORT (AUTO*) PDL FOR NETWORK PORT (AUTO*) I/O TIMEOUT (20 sec.*) PORT SWITCHING *) 6 DEFAULT SETTINGS INTERFACE SETTINGS NETWORK SETTINGS INITIALIZE/STORE SETTINGS PRODUCT KEY [OK] RESTORE FACTORY DEFAULTS [BACK/C] - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 102
CODE CHANGE". 2Touch the KEY OPERATOR PROGRAMS key. ADDRESS CONTROL RECEIVE MODE KEY OPERATOR PROGRAMS 5Press the [CUSTOM SETTINGS] key. For details of will change to asterisks (*). For the factory default setting of the key operator code number (password), see page xxxx. KEY OPERATOR CODE - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 103
copier feature, facsimile feature, and network scanner feature, and additional programs, see their respective manuals scanning originals when using the copier feature, facsimile feature, and network scanner feature. The following functions cannot be used unless the auditing mode for the printer and to - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 104
be set for each feature. Toner consumption can be reduced by approximately 10%. Auto power shut-off When a programmed length of time has elapsed without any operation after printing is complete, the printer enters the auto power shut-off mode to save power consumption at the maximum. This program - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 105
mode or the job status mode when a programmed length has elapsed without any operation on a setting screen. (When the printer is in the mode can be set in 10 second increments up to 240 be applied to the fax mode.) Message display time This default setting. Key touch, completion of original scanning - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 106
copier feature, facsimile feature, and network scanner feature can be printed. Key operator code change This program is used to change the key operator code number (password) from the factory default number (password) can be input. For the factory default key operator code number (password), see - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 107
Default Settings", the following programs can be set. G Print density level G Disable notice page printing G Disable test page printing G A4/letter auto select Print density level This program is used to adjust the lightness or darkness of documents in the print mode instructed to the printer - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 108
PCL emulation is used to print the data from the computer. NOTE It is recommended to set "AUTO" (default setting) unless an error due to this setting occurs frequently. Port switching This program is used to set the switching method of the parallel port and network port of this printer. Setting - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 109
are set when this product is used as a network printer. In "Network Settings", the following programs can be set. After each used to reset all setting items of NIC (Network Interface Card, namely Print Server Card) of this product to the factory default settings. NOTE For programs marked with *1, a - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 110
operator programs (pages xx to xx) can be reset to the factory default settings. Also the current settings can be stored to the memory and the compatible printer The password to be entered is described in the operation manual supplied with the optional PS3 expansion kit. G To use the network scanner - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 111
CHAPTER 7 APPENDIX This chapter describes detailed information of this product such as specifications. Page PRINTER SPECIFICATIONS 7-2 q Specifications 7-2 q List of principal printer functions 7-3 LIST OF COMBINATION OF PERIPHERAL UNITS 7-4 PRINT AREA 7-6 7-1 - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 112
Overall dimensions Weight AR-P350/AR-P450 Desktop Electrophotographic system Semiconductor laser diode system Magnetic brush development Paper trays Heat roller 64 bit RISC, 167 MHz 32 MB One (64 MB to 256 MB memory can be mounted.) PCL6, PCL5e Outline font: 45 Stroke font:1 Line printer font - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 113
List of principal printer functions When an optional PS3 expansion kit is installed General Paper output Paper input Function PCL5e/PCL6 PS PPD (Windows) PPD (Macintosh) Copies Orientation Duplex print Saddle stitch*3 Binding edge N-up 1 - 999 Yes Yes Yes Left/top/right 2/4/6/8 1 - 999 Yes - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 114
extension Punch unit Multi-function controller board Print server card PS3 expansion kit Network scanner expansion kit Facsimile expansion kit Fax memory (8 MB) Power supply unit Hard disk drive Related to scanner feature B/W scanner module/DSPF *1 Scanner rack *1 *1 Related to paper feed - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 115
not too large, a notice page may be printed when the memory is occupied with a copy job, fax jobs, and other jobs.) q The number of print hold jobs is 100 and an additional print hold job is instructed. q Different size paper is included in a print job and a size that cannot be delivered to - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 116
257 A4 210 B5 182 A5 148 Japanese postcard 100 Ledger 279 Legal 216 Foolscap 216 Letter 216 Executive 184 Invoice 140 Com-10 (envelope) 105 C5 (envelope) 162 Monarch (envelope) 98 DL (envelope) 110 ISO B5 (envelope) 176 In case of landscape orientation (in mm) Paper - Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 117
- Sharp AR-M280 | AR-M280 | AR-M350 | AR-M450 Operation Manual (for multifunction - Page 118
Operation Manual
for printer operation and general information on multi functions
LASER PRINTER
(Multi-function printer)