Sharp CD-E77 Service Manual - Page 39

Tracking system check., Check the TE waveform at pin 15 on IC1., Spin

Get Sharp CD-E77 PDF manuals and user guides View all Sharp CD-E77 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

(2) Tracking system check. Check the TE waveform at pin 15 on IC1. If the waveform shown in Figure 39-1 appears and soon after NO DISC appears ? Yes No "Initialization" is possible, but play is not possible ? Yes No "Initialization" is not possible. CD-E700/CD-E77 The tracking servo is not activated. Check the peripheral circuits at pins 14, 15 and 20 on IC1, and CNS1A/B. A normal jump operation cannot be completed or the beginning of the track cannot be found. Check the around pin 20 on IC1. Data cannot be read. Check the VCO-PLL system. Stopped CH1=10 V DC 10:1 T CH2=1 V DC 10:1 100 ms/div (100 ms/div) NORM:100 kS/s TE 2 T DRF 1 (3) Spin system check. Press the OPEN/CLOSE switch without inserting a disc, and then try starting the play operation. =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.0 V CH2 : 0.00 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2 K =Trigger= Mode : NORMAL Type : EDGE CH1 Delay : 2.924 ms Hold off : 0.2 µs Figure 39-1 1. The turntable rotates a little ? (Waveform drawing Figure 39-2) No 2. The turntable doesn't rotate. The spin driver circuit is OK. Yes Check around pin 22 on IC1, pins 15 and 16 on IC2, and CNS3A/B. Stopped CH1=200 mV DC 10:1 T CH2=500 mV DC 10:1 1999/04/07 09:51:15 500 ms/div (500 ms/div) NORM:20 kS/s T FDO 2 SPDO 1 - 39 - =Filter= Smoothing : ON BW : FULL =Offset= CH1 : 0.000 V CH2 : 0.000 V CH3 : 0.00 V CH4 : 0.00 V =Record Length= Main : 100 K Zoom : 2 K =Trigger= Mode : NORMAL Type : EDGE CH2 Delay : 2.924 ms Hold off : 0.2 µs Figure 39-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
– 39 –
CD-E700/CD-E77
T
T
FDO
SPDO
Stopped
CH1=200 mV
DC
10:1
CH2=500 mV
DC
10:1
500 ms/div
1999/04/07
09:51:15
(500 ms/div)
NORM:20 kS/s
2
1
=Record Length=
Smoothing :
ON
CH1
:
0.000 V
CH2
:
0.000 V
Main
:
100 K
Zoom
:
2 K
Mode
:
NORMAL
Type
:
EDGE CH2
Delay
:
2.924 ms
Hold off
:
0.2
μ
s
CH3
:
0.00 V
CH4
:
0.00 V
BW
: FULL
=Trigger=
=Filter=
=Offset=
T
T
TE
DRF
Stopped
CH1=10 V
DC
10:1
CH2=1 V
DC
10:1
100 ms/div
(100 ms/div)
NORM:100 kS/s
2
1
=Record Length=
Smoothing :
ON
CH1
:
0.0 V
CH2
:
0.00 V
Main
:
100 K
Zoom
:
2 K
Mode
:
NORMAL
Type
:
EDGE CH1
Delay
:
2.924 ms
Hold off
:
0.2
μ
s
CH3
:
0.00 V
CH4
:
0.00 V
BW
: FULL
=Trigger=
=Filter=
=Offset=
The tracking servo is not activated.
Check the peripheral circuits at pins 14, 15 and 20 on IC1, and
CNS1A/B.
If the waveform shown in Figure 39-1 appears and soon after
NO DISC appears ?
(2) Tracking system check.
Check the TE waveform at pin 15 on IC1.
A normal jump operation cannot be completed or the beginning of
the track cannot be found.
Check the around pin 20 on IC1.
"Initialization" is possible, but play is not possible ?
Data cannot be read. Check the VCO-PLL system.
"Initialization" is not possible.
Figure 39-1
Figure 39-2
Press the OPEN/CLOSE switch without inserting a disc, and
then try starting the play operation.
(3) Spin system check.
The spin driver circuit is OK.
1. The turntable rotates a little ?
(Waveform drawing Figure 39-2)
Check around pin 22 on IC1, pins 15 and 16 on IC2, and CNS3A/B.
2. The turntable doesn't rotate.
No
Yes
No
Yes
Yes
No