Sharp PN-E802 User Manual - Page 42

■ To set from a PC, Set up process, Connecting your monitor to a PC, Specifying the PC's IP address

Get Sharp PN-E802 PDF manuals and user guides View all Sharp PN-E802 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Controlling the Monitor with a PC (LAN) ■ To set from a PC When the monitor is connected to a PC, LAN settings can be configured via PC. Set up process (1) Connect your monitor to a PC (2) Specify the PC's IP address (3) Configure the monitor's LAN settings (1) Connecting your monitor to a PC Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor. 7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows. • IP Address: 192.168.150.1 • Subnet Mask: 255.255.255.0 • Default Gateway: (leave blank) 8. Click [OK] and then reboot the PC. LAN terminal PC To LAN terminal TIPS • This monitor is factory preset as shown below. (When DHCP CLIENT is set to OFF) IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 LAN cable (commercially available, crossover) (2) Specifying the PC's IP address To configure the monitor's LAN settings, you must temporarily change the settings on the PC. This explanation is based on Windows 7. 1. Log on to the PC with an administrator account. 2. Click [Start], and then click "Control Panel". 3. Click "View network status and tasks" in "Network and Internet". In "Classic View", click "Network and Sharing Center". 4. Click "Local Area Connection" and then "Properties". 5. Click "Internet Protocol Version 4 (TCP/IPv4)" and then "Properties". 6. Make a note of the current IP address, subnet mask, and default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards. (3) Configuring the monitor's LAN settings Access the monitor using Internet Explorer. Controlling the monitor 1. Turn the power ON to the monitor. 2. Set RS-232C/LAN SELECT on the SETUP menu to LAN. 3. Set DHCP CLIENT to OFF in LAN SETUP on the SETUP menu. PC operation 4. Launch Internet Explorer, in the "Address" box type "http://192.168.150.2/" and press the Enter key. You will be prompted to enter a user name and password. 5. Leave the user name and password boxes blank and click [OK]. E 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
42
E
■ To set from a PC
When the monitor is connected to a PC, LAN settings can be
configured via PC.
Set up process
(1) Connect your monitor to a PC
(2) Specify the PC’s IP address
(3) Configure the monitor’s LAN settings
(1) Connecting your monitor to a PC
Connect a commercially available crossover LAN cable
(UPT cable, Category 5) to the LAN
port on the PC and this
monitor.
LAN cable
(commercially available, crossover)
To LAN terminal
PC
LAN terminal
(2) Specifying the PC’s IP address
To configure the monitor’s LAN settings, you must temporarily
change the settings on the PC.
This explanation is based on Windows 7.
1. Log on to the PC with an administrator account.
2. Click [Start], and then click “Control Panel”.
3. Click “View network status and tasks” in “Network and
Internet”.
In “Classic View”, click “Network and Sharing Center”.
4. Click “Local Area Connection” and then “Properties”.
5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then
“Properties”.
6. Make a note of the current IP address, subnet mask, and
default gateway settings.
Make sure you write this information now as you will
be changing the IP address, subnet mask, and default
gateway settings back to these settings afterwards.
7. Temporarily change the IP address and subnet mask.
To access the monitor as it is shipped from the factory, set
as follows.
• IP Address: 192.168.150.1
• Subnet Mask: 255.255.255.0
• Default Gateway: (leave blank)
8. Click [OK] and then reboot the PC.
TIPS
•
This monitor is factory preset as shown below.
(When DHCP CLIENT is set to OFF)
IP Address
: 192.168.150.2
Subnet Mask
: 255.255.255.0
Default Gateway : 0.0.0.0
(3) Configuring the monitor’s LAN settings
Access the monitor using Internet Explorer.
Controlling the monitor
1. Turn the power ON to the monitor.
2. Set RS-232C/LAN SELECT on the SETUP menu to LAN.
3. Set DHCP CLIENT to OFF in LAN SETUP on the SETUP
menu.
PC operation
4. Launch Internet Explorer, in the “Address” box type
“http://192.168.150.2/” and press the Enter key.
You will be prompted to enter a user name and password.
5. Leave the user name and password boxes blank and click
[OK].
Controlling the Monitor with a PC (LAN)