Singer 1 One Instruction Manual 19

Singer 1 One Manual

Get Singer 1 One PDF manuals and user guides View all Singer 1 One manuals
Add to My Manuals
Save this manual to your list of manuals

Singer 1 One manual content summary:

  • Singer 1 One | Instruction Manual 19 - Page 1
    1 4SH644 ( 3 • 4 THREAD OVERLOOK MACHINE) 1 4SH654 ( 3 4 THREAD OVERLOOK MACHINE WITH DIFFERENTIAL FEED) Operator's Guide I \\ SINGER uovainit I SINGER®
  • Singer 1 One | Instruction Manual 19 - Page 2
    to change the appearance, design or accessories of this sewing machine when considered necessary without notification or obligation. IMPORTANT SAFETY INSTRUCTIONS * If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to
  • Singer 1 One | Instruction Manual 19 - Page 3
    area, such as threading needle and loopers, changing needle, changing throat plate or changing presser foot, etc. • Always unplug the machine from the electrical outlet when removing covers, lubricating, or when making any other user servicing adjustments mentioned in the Operator's Guide • Do not
  • Singer 1 One | Instruction Manual 19 - Page 4
    not keep it in a very warm or damp place. * Do not touch the machine, foot controller and power line cord with wet hand, wet cloth or caring for your machine as instructed in the operator's guide. SAVE THESE INSTRUCTIONS Servicing should be performed by an authorized service representative. This
  • Singer 1 One | Instruction Manual 19 - Page 5
    1) 3-Thread Overlock 29 2) 3-Thread Flatlock 30 3) 3-Thread Wrapped Edge Overlock 31 4) 4-Thread Ultra Stretch Mock Safety Stitch 32 22. How to Sew a Rolled Hem 33 1) 3-thread standard rolled hem stitching 34 2) 3-thread upper looper thread wrapped rolled hem stitching 34 23. Stitch
  • Singer 1 One | Instruction Manual 19 - Page 6
    width can be obtained by changing the needle position.* (505) 3. Three-thread Wrapped Edge Overlock , 1-needle 3-thread stitch is used for sewing narrow rolled hems or ornamental edges. Also, a 3.5mm and 5.7mm wrapped 31 overlock seam width can be obtained by changing the needle position
  • Singer 1 One | Instruction Manual 19 - Page 7
    2.0 :i2 Safety Stitch IP IP (514) The thread tension becomes tighter as the dials are turned to higher numbers. The tension settings shown on this page as well as throughout the operator's manual are suggested guides. Adjust thread tensions to suit the fabric and size of thread used. For best
  • Singer 1 One | Instruction Manual 19 - Page 8
    4. NEEDLE INFORMATION • Singer needle #2022 size 90/14 is furnished with the machine. • In an emergency, standard Singer needle #2020 may be used. However, unless the suggested tension setting is readjusted, skipping of the stitches may occur. Sizes available Singer needle #2022 80/11 90/14
  • Singer 1 One | Instruction Manual 19 - Page 9
    PARTS 1 Thread guides and holder 2 Handle 3 Left needle thread tension dial (blue) 4 Right needle thread tension dial (green) 5 Upper looper thread tension dial (orange) 6 Lower looper thread tension dial (yellow) 7 Throat plate 8 Cloth plate 9 Looper cover 10 Power & light switch 11 Stitch length
  • Singer 1 One | Instruction Manual 19 - Page 10
    mark side to turn "ON". Push "0" mark side to turn "OFF". • To run the machine and control the speed, press the controller. • The harder you press, the faster the machine will sew. • To stop the machine from sewing, remove your foot from the controller. ON OFF 2 it 3 4 WARNING: Use only foot
  • Singer 1 One | Instruction Manual 19 - Page 11
    eliminates the possibility of starting the machine by accidentally pressing the controller. 9. PREPARATION FOR THREADING Setting Up the Thread Guide Holder • This machine is shipped with the thread guide holder in the lowered position. • Fully extend the thread guide holder. • The two joints on the
  • Singer 1 One | Instruction Manual 19 - Page 12
    surface to the back. • Insert the needle into the needle clamp as far as it will go. • Securely tighten the needle set screw. Note: *This machine uses #2022 needles. Refer to page 17 for additional needle information. * Remove the cloth plate if you find it difficult to remove and replace the
  • Singer 1 One | Instruction Manual 19 - Page 13
    needle thread Orange Yellow Green Blue To Thread The Machine Correctly A Caution : Be sure to turn off power switch. 1) Threading the Upper Looper (Orange) • Thread the upper looper as indicated 1 - 8 . ®C)C, I I I I 0 2 4, 3 • Pass thread from back to the front through the thread guide 1 . 12
  • Singer 1 One | Instruction Manual 19 - Page 14
    down to make certain it is properly located in between the tension discs 3 . 3 • Thread the looper area of the machine following the orange color coded thread guides ( 4 - 7 ). • Thread the hole in the upper looper from front to back 8. Note: Use of tweezers provided in the accessory set to aid
  • Singer 1 One | Instruction Manual 19 - Page 15
    guide 1 . 1. • Thread the top cover thread 1 guide by pulling the thread downward until it slips under thread guide 2 . • While holding thread with finger, pass it between the tension discs and pull thread down to make certain it is properly located in between the tension discs 3 . 2 14 SINGER
  • Singer 1 One | Instruction Manual 19 - Page 16
    looper area of the machine following the yellow color coded thread guides 4 - 7 . Note: Use the tweezers provided in the accessory set to aid in threading the looper. • /1 • ) 15) • Grasp the thread with the tweezers 4 cm (1-1/2 inches) from thread guide 7. • Place the thread with the point of
  • Singer 1 One | Instruction Manual 19 - Page 17
    • Thread the top cover thread guide by pulling the thread downward until it slips under thread guide 2. \.. • While holding thread with finger. pass it between the tension discs and pull thread down to make certain it is properly located in between the tension discs 3 . 3 2 16 2 4$ SINGER
  • Singer 1 One | Instruction Manual 19 - Page 18
    4 - 6 . Note: Be sure to pass the thread through upper thread path of the thread guide 6 . 6 4 • • Thread the eye of the right needle 8 . Note: Use of tweezers in the accessory set will make needle eye threading easy. • Draw about 10cm (4 inches) of thread through needle eye to hang free. • Place
  • Singer 1 One | Instruction Manual 19 - Page 19
    from back to the front through the thread guide 1 . 2) 5 6 1 I • Thread the top cover thread guide by pulling the thread downward until it slips under thread guide 2 . • While holding thread with finger, pass it between the tension discs and pull thread down to make certain it is properly
  • Singer 1 One | Instruction Manual 19 - Page 20
    4 - 5. Note: Be sure to pass the thread through lower thread path of the thread guide 5 . 5 4) • Thread the eye of the left needle 7 . Note: Use of tweezers in the accessory set will make needle eye threading easy. • Draw about 10cm (4 inches) of thread through needle eye to hang free. • Place
  • Singer 1 One | Instruction Manual 19 - Page 21
    . sf9 • Turn the tension dials down until the dial stops. • Pull the threads through the machine one at a time. • If threads do not pull easily, check for tangles on thread guides or looping under thread stand. • When pulling thread through the needle, STOP when the knot is in front of the needle
  • Singer 1 One | Instruction Manual 19 - Page 22
    length dial should be set on the 3 mm (1/8 inch) setting for most sewing conditions. • Adjust the stitch length to 4mm (5/32 inch) when sewing heavy weight fabrics. • Adjust the stitch length to 2mm (5/64 inch) when sewing light weight fabrics to obtain excellent seams without puckering. 14. HOW TO
  • Singer 1 One | Instruction Manual 19 - Page 23
    furnished with the machine and using the graduations on the throat plate as a guideline, set edge (A) of the seam width finger support plate to desired machine. 15. HOW TO ADJUST THE PRESSER FOOT PRESSURE • The presser foot pressure of this machine is preadjusted at the factory to suit the sewing
  • Singer 1 One | Instruction Manual 19 - Page 24
    before sewing your garment. • When feed regulating dial is set at "3" or over, the amount of feed of the main feed dog will change to "3" automatically when adjusting lever knob is set to 2.0. Note: For normal overedge stitching, set differential feed adjusting lever knob to graduation "1.0". 23
  • Singer 1 One | Instruction Manual 19 - Page 25
    To set the differential feed adjusting lever • Set differential feed adjusting lever knob above graduation "1.0". • To sew a seam, apply gentle tension to the fabric by holding the seam lightly in front and back of feed adjusting lever to graduation "1.0" for normal overedge stitching. 24
  • Singer 1 One | Instruction Manual 19 - Page 26
    a horizontal position. Note: If the knife stops in the up position; * Turn the hand wheel toward you until the knife clears the top of the machine. * Continue to rotate the knife to the horizontal position. To place movable knife in working position • Open looper cover and push the movable knife
  • Singer 1 One | Instruction Manual 19 - Page 27
    to the left and remove from machine while pressing button (A) located on the underside. • This is especially suited for sewing hard to reach garment areas such and overcasting trouser cuffs. • Place garment over the free arm and sew. • To replace the cloth plate • Align projection on cloth plate
  • Singer 1 One | Instruction Manual 19 - Page 28
    AND ROLLED HEM STITCHING To Sew Standard Overedge • Set seam width finger knob to S to move seam width finger to projected position. Note: Be sure to push seam width finger knob as far as it will go in the direction of setting S . in CD I Seam width figer knob 0 To Sew Rolled Hem • Set
  • Singer 1 One | Instruction Manual 19 - Page 29
    OFF AND TEST SEWING • When the machine is completely threaded, bring all of the threads over the throat plate and slightly to the left under the presser foot. • Hold the threads and apply a slight tension. • Turn the hand wheel toward you 2 or 3 complete turns to start the thread chain. • Lower
  • Singer 1 One | Instruction Manual 19 - Page 30
    2) Needle size 3) Size, type and fiber content of thread NEEDLE POSITION • O O• SEAM WIDTH FINGER KNOB STITCH LENGTH S 2- 4 Upper looper thread Needle thread Correct Balance • Set Each Tension Dial to Settings Shown at Right and Test Sew on a Sample of Your Fabric Topside Lower looper
  • Singer 1 One | Instruction Manual 19 - Page 31
    NEEDLE POSITION •O OIP SEAM WIDTH FINGER KNOB STITCH LENGTH S 2- 4 Correct balance • Set Each Tension Dial to Settings Shown at Right and Test Sew on a Sample of Your Fabric Needle thread Upper looper thread Topside eedl thread tower looper thread Underside (505) Fabric Light weight Medium
  • Singer 1 One | Instruction Manual 19 - Page 32
    NEEDLE POSITION GPO CAP SEAM WIDTH FINGER KNOB STITCH LENGTH S 2 - 4 Correct Balance • Set Each Tension Dial to Settings Shown at Right and Test Sew on a Sample of Your Fabric Needle thread Upper looper thread ower I•,• per thread Topside Needle threa4 Underside Fabric Light weight Medium
  • Singer 1 One | Instruction Manual 19 - Page 33
    of fabric 2) Needle size 3) Size, type and fiber content of thread NEEDLE POSITION SEAM WIDTH FINGER KNOB STITCH LENGTH SW S 2 - 4 Upper looper thread Correct Balance • Set Each Tension Dial to Settings Shown at Right and Test Sew on a Sample of Your Fabric How to Balance • When the upper
  • Singer 1 One | Instruction Manual 19 - Page 34
    left face of seam width finger support plate with R mark on throat plate by turning seam width finger knob, as required. • Set stitch length dial to "F 2" and a fine seam will be sewn. • Needle: Singer Needle #2022 size 80/11 or 90/14 • Thread: A variety of thread combinations can be used for rolled
  • Singer 1 One | Instruction Manual 19 - Page 35
    2.5 2) 3-thread Upper Looper Thread Wrapped Rolled Hem Stitching Correct Balance • Set Each Tension Dial to Settings Shown at Right and Test Sew on a Sample of Your Fabric Needle thread Upper looper thread Topside Lower looper thread Needle thread Underside Upper Looper Thread Polyester Woolly
  • Singer 1 One | Instruction Manual 19 - Page 36
    Information About Rolled Hemming • Hold the thread chain when you begin sewing to keep it from curling into the seam. • Place a slight tension on the material in the sewing direction and a finer seam finish can be obtained. • The minimum overedge stitch width that can be 4. obtained for
  • Singer 1 One | Instruction Manual 19 - Page 37
    is achieved by adjusting the tension of the 3-thread overlock stitch, sewing the seam and pulling the fabric apart to flatten the seam. • The flatlock stitch can be used as a construction and decorative stitch or for ornamentation only. (1) Machine Set Up • Remove the left or right needle. • Begin
  • Singer 1 One | Instruction Manual 19 - Page 38
    • The upper looper thread is the prominent thread in the flatlock stitch. Place a decorative thread in the upper looper and inconspicuous threads in the lower looper and needle. • For a ladder stitch, sew seam with right sides together. The needle thread will be the prominent thread that creates the
  • Singer 1 One | Instruction Manual 19 - Page 39
    hem is best suited for sewing knit wear. It provides a durable finish that is almost invisible. 111 1I • Remove the left needle and adjust machine for a narrow 3-thread overlook stitch. 0 0 Note: The three-thread flatlock stitch can also be used. • Set the stitch length dial at 4. • Fold the
  • Singer 1 One | Instruction Manual 19 - Page 40
    (51/64 inch) from the corner, in line with the overedge seam edge. • Sew one stitch beyond point (A) and stop. • Raise needle and presser foot. • Pull the fabric to the rear of the machine just enough to release the thread caught on the finger of the throat plate. Note: Presser foot has been removed
  • Singer 1 One | Instruction Manual 19 - Page 41
    are away from the cutting action of the knives. •;\ A Caution: Sewing over pins will damage and/or destroy the cutting edge of the knives. Securing the Thread Chain • Thread a large eye, hand sewing needle (such as a tapestry needle) with the thread chain. • Insert the needle into the end of the
  • Singer 1 One | Instruction Manual 19 - Page 42
    the seam. • Insert the tape through the hole in the front of the foot. • Position the tape under the foot to the back of the machine and sew the garment seam. • The tape is attached as the seam is sewn. Braiding by Chaining Off • Place the movable upper knife in nonworking position
  • Singer 1 One | Instruction Manual 19 - Page 43
    : Lint brush is an optional part. bei ( Oiling the Machine A Danger: Before lubricating your machine, disconnect power line plug from the wall receptacle. • The oiling points shown in the diagram, should be oiled periodically. Note: Use sewing machine oil. Do not use any other oil or damage
  • Singer 1 One | Instruction Manual 19 - Page 44
    it becomes dull. • The stationary knife can be replaced according to the directions provided, however if there are any difficulties experienced, consult your Singer representative to make the adjustments. • Be sure that the power line plug is disconnected from the electric source. • Open the looper
  • Singer 1 One | Instruction Manual 19 - Page 45
    A Danger: Always unplug before relamping • Light bulb is available at your Singer shop. Take old bulb to the Singer shop and ask for same bulb. • If voltage indicated on the electrical rating plate of your machine is 110 127V, ask for light bulb conforming to following specification. - Bayonet
  • Singer 1 One | Instruction Manual 19 - Page 46
    25. TROUBLESHOOTING CHART Problem Solution Fabric does not feed well Needle breaks Thread breaks Stitches skip Irregular stitches Fabric puckers Irregular trimming Fabric jams Machine does not operate ' - Lengthen stitch length. - Increase presser foot pressure for heavy weight fabric. -
  • Singer 1 One | Instruction Manual 19 - Page 47
    , Voil, Crepe, etc. Type of Thread Cotton: #100 Silk: #100 Spun: #80 - #90 Tetron: #80 - #100 Needle Singer Cat. No. 2022 #11 Medium Weight 60 - #80 Tetron: #50 - #60 Woolly nylon Woolly tetron Singer needle, Cat. No. 2022 is furnished with the machine however. #14 #11 #11, #14 #11, #14 It
  • Singer 1 One | Instruction Manual 19 - Page 48
    27. SPECIFICATION Item Specification Sewing speed Stitch length (feed amount) Differential feed ratio Overedge stitch width Needle bar stroke Presser foot rise Needle Model Number of threads Machine dimensions (mm) Width Depth Height Weight (Kg) 1,300 spm maximum 1 - 4mm (standard: rolled
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
1
4SH644
(
3
•
4
THREAD
OVERLOOK
MACHINE)
1
4SH654
(
3
4
THREAD
OVERLOOK
MACHINE
WITH
DIFFERENTIAL
FEED)
Operator's
Guide
I
\\
SINGER
u
ovainit
I
SINGER®