Singer 1 One Instruction Manual 37

Singer 1 One Manual

Get Singer 1 One PDF manuals and user guides View all Singer 1 One manuals
Add to My Manuals
Save this manual to your list of manuals

Singer 1 One manual content summary:

  • Singer 1 One | Instruction Manual 37 - Page 1
    14U 34B/234B Operator's Guide 111 5 INGER SINGER
  • Singer 1 One | Instruction Manual 37 - Page 2
    from light to heavy material (lawn to denim). Please refer to this booklet for proper use and optimum service. To get the most out of your sewing machine, read the entire operator's manual before attempting to operate the machine. Then familiarize yourself with the ma chine by follwing the operator
  • Singer 1 One | Instruction Manual 37 - Page 3
    care is required around the sewing machine needle. ■ Do not pull or push fabric while stitching. It may deflect the needle causing it to break. ■ For double insulated machines, when servicing use only identical replacement parts. See instructions for Servicing of Double-Insulated Appliances. ■ Use
  • Singer 1 One | Instruction Manual 37 - Page 4
    product. A double-insulated product is marked with the words "DOUBLE-INSULATION" or "DOUBLE-INSULATED." SAVE THESE INSTRUCTIONS Servicing should be performed by an authorized service representative. This product is intended for household use. FOR EUROPEAN AND SIMILAR TERRITORIES : This product is
  • Singer 1 One | Instruction Manual 37 - Page 5
    feed (with differential feed machine only) 15 • Gathered overedge 15 • Stretch overedge 16 11. Free arm sewing (tubular work) 17 12. Seam guide lines 17 13. Edge guide (optional parts) 17 14. Variation stitch 18 • Ornamental stitching 18 • Blindstitching 19 • Braiding by chaining
  • Singer 1 One | Instruction Manual 37 - Page 6
    Principal parts Thread guide holder Left hand looper thread tension dial Right hand looper thread tension dial Pressure regulating screw Right needle thread tension dial Left needle thread tension dial Handle Spool pin Convertible bed plate Throat plate Free arm SINGER Looper cover • Machine
  • Singer 1 One | Instruction Manual 37 - Page 7
    2. Preparation prior to sewing Connect the machine plug to the electrical receptacle of your speed, press the speed controller. The harder you press, the faster the machine will sew. To stop the machine from sewing, remove your foot from the speed controller. Warning: • Be sure that the electrical
  • Singer 1 One | Instruction Manual 37 - Page 8
    guide holder • How to open looper cover Thread guide Thread guide-4 holder ICI L SINGER no+ I I Spool stand Extend the thread guide holder as far as possible and set the thread guides you. Caution: * Be sure looper cover is closed when sewing. To replace cover T 40 V \L_ Throat plate 0
  • Singer 1 One | Instruction Manual 37 - Page 9
    • How to thread your machine correctly Correct sewing cannot be obtained when machine is threaded incorrectly. Threading is diagrammed on the inner side of the looper cover and identified with colors on the various thread guides. (1) Open looper cover. Thread the right looper in the order 0 to ® as
  • Singer 1 One | Instruction Manual 37 - Page 10
    (2) Thread left looper in sequence from ® to C) (marked in yellow color). Cylinder cover must also be removed when threading this part. (Refer to page 4 for cylinder cover removal). While holding thread with finger, pass it between the tension discs and pull thread down to make certain it is
  • Singer 1 One | Instruction Manual 37 - Page 11
    (3) Thread the left needle thread in the order 0 to 8 (blue mark). Threading of needle eye 8 becomes easier when the movable knife is set at the non-operating posi- tion (See figure on page 12 for movable knife non-operating position). D 0 IN° f While holding thread with N finger, pass it
  • Singer 1 One | Instruction Manual 37 - Page 12
    before the needle eye, cut the thread and pass it through the needle eye. (5) Return tension dials to reference numbers. 4. Chain off and test sew SINGER 14. 1 Cloth 8 /.. by CD Tie knot--_ y n When the machine is completely threaded, turn the hand wheel toward you 2 or 3 turns while holding the
  • Singer 1 One | Instruction Manual 37 - Page 13
    5. 1-Needle, 3-Threads overedge stitching This is a two needles four threads overedge machine but one needle three threads overedge can be done by means of using only the left or right needle and three threads. No. of thread Overedge width
  • Singer 1 One | Instruction Manual 37 - Page 14
    size of the thread used. The thread tension dials on this machine are a one-turn system and as the number on the thread tension dials increases, the thread of the thread tension dials to the settings shown below and test sew. it Right needle thread Left needle thread Topside Left looper thread
  • Singer 1 One | Instruction Manual 37 - Page 15
    tension cannot be obtained (See page 5). Right looper thread Set each of the thread tension dials to the settings shown below•and test sew. Needle thread Topside Left looper thread Underside • When using the left needle, be sure to remove the right needle. ----s-Thread tension Left needle
  • Singer 1 One | Instruction Manual 37 - Page 16
    seam width SINGER Overedge seam width of this machine is set to 3.5 mm for normal sewing with right needle and 5.7 mm with left needle however it can be increased up to 5 mm for overedge heavy weight fabrics with right needle and 7.2 mm with left needle as instructed
  • Singer 1 One | Instruction Manual 37 - Page 17
    page 25) • Rolled hemming is done by rolling the fabric and overedging (seam width 1.5mm), and is not suited for heavy or stiff fabrics. Needle: Singer Cat. No. 2054 (#10), #14. Thread: A variety of thread combinations can be used for rolled hemming. 0 Stitch length adjustment (See page 12) For
  • Singer 1 One | Instruction Manual 37 - Page 18
    dial settings. a. Turn the right looper thread tension dial (orange) one half graduation toward the (-) mark. b. Turn the left looper thread How to sew Sewing • See page 8, "4. Chain off and test sew". • For rolled hemming, if a slight tension is applied to the material in the sewing direction, a
  • Singer 1 One | Instruction Manual 37 - Page 19
    10. Differential feed (with differential feed machine only) Differential feed is a system which "stretches" or "gathers" the fabric, when amount of feed of front feed dog in relation to the rear feed dog is changed. The differential feed ratio ranges from 1:0.77 -1:2.0. Adjustment is made by means
  • Singer 1 One | Instruction Manual 37 - Page 20
    feed adjusting lever thumb screw. • Slide adjusting lever upward above the center mark, as required, to stretch, and tighten the thumb screw (Fig. 1) To sew a seam, apply gentle tension to the fabric by holding the seam lightly in front and back of the presser foot. (Fig. 2) Note: If amount of
  • Singer 1 One | Instruction Manual 37 - Page 21
    the free arm and sew. 12. Seam guide lines Use seam guide lines on looper cover to guide (optional parts) For ornamental and blind (overedge) stitching, use of the edge guide attachment is very convenient. Attach edge guide as shown in figure. 5/8" ill SINGER 14u Edge guide Washer Nay Edge guide
  • Singer 1 One | Instruction Manual 37 - Page 22
    : Right looper thread Left looper thread Needle thread Stitch length Woolly nyron extra fine extra fine 2 -3 1. Set thread tensions to normal sewing condition for 1 needle, 3 thread overedge stitch and make a test sample. (See page 11). Needle thread • When making above adjustment, the right
  • Singer 1 One | Instruction Manual 37 - Page 23
    Place fabric under the foot with the fold resting against the wall of edge guide. Adjust edge guide so that it is positioned in the center of the seam width as shown Knit fabric Ordinary overedge throat plate Set tensions to normal sewing condition for 1 needle, 3 thread overedge stitching (see
  • Singer 1 One | Instruction Manual 37 - Page 24
    . (optional parts) • Adjust edge guide (optional parts) so that the stitches will just overcast the edge of the fold as shown in the sketch. • Lower the foot and sew. When stitching is completed, press pin tuck to lay flat on one side. • Turning square corners Outside corner Cutting --'1 line 2cm
  • Singer 1 One | Instruction Manual 37 - Page 25
    movable knife in non-operating position. 3. Fold fabric as shown in sketch. 4. Sew to point B, as close as possible to the diagonal fold. Leave needle in fabric in line with the already sewn seam. 15. How to replace needles Use Singer needles Cat. No. 2054 available in sizes #14 and (#10) To
  • Singer 1 One | Instruction Manual 37 - Page 26
    the following steps, however if there are any difficulties experienced, call your Singer representative to make the adjustment. (1) Be sure that the power pressure of this machine is preadjusted at the factory to suit the sewing of medium weight fabrics. Less pressure Pr-) More pressure It may
  • Singer 1 One | Instruction Manual 37 - Page 27
    19. Cleaning Your machine will serve you perfectly for many years if you take a few moments of your time to keep it clean. Danger: Before cleaning your machine, disconnect power line plug from the wall receptacle. Open looper cover and remove lint and fluff which may have accumulated around the
  • Singer 1 One | Instruction Manual 37 - Page 28
    make adjustment Whenever sewing difficulty is encountered Do not pull the fabric by hand. Use hand only to guide the fabric. • Tighten screw firmly. • Incorrect threading. • Bent (page 21). • Thread machine correctly (page 5). • Use Singer Cat. 2054, #14. • Insufficient presser foot pressure. •
  • Singer 1 One | Instruction Manual 37 - Page 29
    #80 Spun #60 - #80 Tetron #50 - #60 Woolly nylon Woolly tetron Needle Singer Cat. No. 2054 (#10), #14 #14 #14 (#10), #14 #14 #14 Singer needle, Cat. No. 2054-42 is furnished with the machine however, the following variety select your needle in accordance with the material you are sewing. 25
  • Singer 1 One | Instruction Manual 37 - Page 30
    throat plate 1 6. Hex-head wrench 1 23. Specification Item Sewing speed Stitch length (feed amount) Differential feed ratio Overedge stitch 3.5 - 7.2mm (standard 3.5mm) 27mm 5mm Rolled hemming Singer Cat. No. 2054 (#10), #14 Ordinary overedge Singer Cat. No. 2054 (#10), #14 4 width 257mm
  • Singer 1 One | Instruction Manual 37 - Page 31
    Form U3865 (Rev. 393) Part No. 379211-002 (Rev. 4) Printed in Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
14
U
34B/234B
Operator's
Guide
111
5
INGER
SINGER