Sony KDP-65WS550 Primary User Manual - Page 115

General, Cannot operate Menu - blinks

Get Sony KDP-65WS550 - 65inch High Definition Projection Tv PDF manuals and user guides View all Sony KDP-65WS550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 115 highlights

Welcome SETUP General Problem Possible Remedies How to reset TV to ❏ Turn on the TV. While holding down the RESET button on the remote factory settings control, press the POWER button on the TV. (The TV will turn itself off, then back on again.) Release the RESET button. How to restore Video settings ❏ Press the RESET button on the remote control while in the Video Menu (see to factory settings page 92). How to restore Audio ❏ Press the RESET button on the remote control while in the Audio Menu (see settings to factory settings page 94). Cannot cycle through the ❏ Be sure the Video Label option is not set to Skip (see page 104). other video equipment connected to the TV Cannot operate Menu ❏ If a menu option appears in gray, this indicates that the TV is in a state in which the menu option is not available. Lost password ❏ In the password screen (see page 100), enter the following master password: 4357. The master password clears your previous password; it cannot be used to temporarily unblock channels. LED on front panel is lit ❏ The STAND BY LED (see page 15) blinks when the TV is turned on, then shuts off when the picture is displayed. If the LED blinks continuously, this may indicate the TV needs service. ❏ The TIMER LED (see page 15) indicates that the timer is set. When the timer is set, this LED will remain lit even when the TV is turned off. ❏ The i.LINK STANDBY LED blinks when the signal from an i.LINK device is being shown. The signal from a selected ❏ If you have several i.LINK devices connected and operating at once, the TV i.LINK device is not being may not be able to display the signal from the selected device. Turn the displayed other i.LINK devices off, and reselect the desired i.LINK device. SETUP Other Info Other Info Other Info 114

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
114
Other Info
Other Info
Welcome
Other Info
SETUP
SETUP
General
Problem
Possible Remedies
How to reset TV to
factory settings
❏
Turn on the TV. While holding down the
RESET
button on the remote
control, press the
POWER
button on the TV. (The TV will turn itself off, then
back on again.) Release the
RESET
button.
How to restore Video settings
to factory settings
❏
Press the
RESET
button on the remote control while in the Video Menu (see
page 92).
How to restore Audio
settings to factory settings
❏
Press the
RESET
button on the remote control while in the Audio Menu (see
page 94).
Cannot cycle through the
other video equipment
connected to the TV
❏
Be sure the
Video Label
option is not set to
Skip
(see page 104).
Cannot operate Menu
❏
If a menu option appears in gray, this indicates that the TV is in a state in
which the menu option is not available.
Lost password
❏
In the password screen (see page 100), enter the following master
password:
4357
. The master password clears your previous password; it
cannot be used to temporarily unblock channels.
LED on front panel is lit
❏
The STAND BY LED (see page 15) blinks when the TV is turned on, then
shuts off when the picture is displayed. If the LED blinks continuously, this
may indicate the TV needs service.
❏
The TIMER LED (see page 15) indicates that the timer is set. When the
timer is set, this LED will remain lit even when the TV is turned off.
❏
The i.LINK STANDBY LED blinks when the signal from an i.LINK device
is being shown.
The signal from a selected
i.LINK device is not being
displayed
❏
If you have several i.LINK devices connected and operating at once, the TV
may not be able to display the signal from the selected device. Turn the
other i.LINK devices off, and reselect the desired i.LINK device.