Sony KLV-S20G10 Operating Instructions - Page 25

Connecting Optional Equipment, VCR, Cable and Antenna, Cable and, Antenna

Get Sony KLV-S20G10 - 20inch Lcd Wega Flat Panel Television PDF manuals and user guides View all Sony KLV-S20G10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Connecting the TV Connecting the TV Connecting Optional Equipment You can connect a variety of optional equipment to your TV. This section provides some of the individual connections you can make. For multiple connections, please refer to the Quick Setup Guide. VCR, Cable and Antenna z The most common setup is the Cable input into the VCR Antenna IN, the VCR Antenna Out to the VHF/UHF input. This scenario shows a VCR with Cable signals connected through the video inputs and the Antenna connected through the VHF/UHF input. The Cable or VCR signals are selected by the VCR through the video inputs while TV signal is selected by the TV tuner. To connect the VCR and cable 1 Connect the CATV cable to the VCR's VHF/UHF input jack. 2 Connect the supplied 75-ohm coaxial cable from the antenna to the TV's VHF/UHF input jack. 3 Use A/V and S VIDEO cables to connect the VCR's AUDIO and S VIDEO output jacks to the TV's AUDIO and S VIDEO input jacks (VIDEO 1 IN). 4 Run the Initial Setup Program, as described in "Setting Up the Channel List" on page 31. If your VCR is not equipped with S VIDEO, use a VIDEO cable (yellow) instead of the S VIDEO cable. (Continued) 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Connecting the TV
25
Connecting the TV
Connecting Optional Equipment
You can connect a variety of optional equipment to your TV. This section
provides some of the individual connections you can make. For multiple
connections, please refer to the Quick Setup Guide.
VCR, Cable and
Antenna
This scenario shows a VCR with Cable signals connected through the video
inputs and the Antenna connected through the VHF/UHF input. The Cable
or VCR signals are selected by the VCR through the video inputs while TV
signal is selected by the TV tuner.
To connect the VCR and cable
1
Connect the CATV cable to the VCR’s VHF/UHF input jack.
2
Connect the supplied 75-ohm coaxial cable from the antenna to the
TV’s VHF/UHF input jack.
3
Use A/V and S VIDEO cables to connect the VCR’s AUDIO and
S VIDEO output jacks to the TV’s AUDIO and S VIDEO input jacks
(VIDEO 1 IN).
4
Run the Initial Setup Program, as described in “Setting Up the Channel
List” on page 31.
If your VCR is not equipped with S VIDEO, use a VIDEO cable
(yellow) instead of the S VIDEO cable.
z
The most common
setup is the Cable input
into the VCR Antenna
IN, the VCR Antenna
Out to the VHF/UHF
input.
(Continued)