Sony XAV-AX5600 Operating Instructions - Page 15

Using the wired remote control, Using an HDMI device, Using the rear view camera, Cautions

Get Sony XAV-AX5600 PDF manuals and user guides View all Sony XAV-AX5600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Cautions • It is extremely dangerous if the cord becomes wound around the steering column or gearstick. Be sure to keep it and other parts from interfering with your driving operations. • If airbags or any other shock-absorbing equipment are in your car, contact the store where you purchased this unit or the car dealer before installation. Notes • When mounting on the dashboard, remove the visor clip carefully from the microphone , then attach the flatmount base  to the microphone . • Before attaching the double-sided tape , clean the surface of the dashboard with a dry cloth. Using the wired remote control When using the steering wheel remote control Installation of the connection cable RC-SR1  is required before use. 1 To enable the steering wheel remote control, select [General]  [Steering Control]  [Custom]  to make the registration. When the registration is complete, the steering wheel remote control becomes available. Notes on installing the connection cable RC-SR1  • Refer to the support site for details then connect each lead properly to the appropriate leads. Making an improper connection may damage the unit. URL: https://www.sony.com/am/support • Consulting the dealer or an experienced technician for help is recommended. When using the wired remote control 1 To enable the wired remote control, set [Steering Control] in [General] to [Preset]. Using an HDMI device Installation of an HDMI cable (not supplied) is required before use. 1 Connect an HDMI cable to the HDMI terminal at the back panel of the unit. 2 Pass the cable tie  through the cable holder, then tie the cable tie  around the HDMI cable. The HDMI cable is secured to the unit. *  * HDMI cable (not supplied) 3 Connect the installed HDMI cable to an HDMI device. 4 Press HOME, then touch [HDMI]. The HDMI device connected will be mirrored to this unit. Using the rear view camera Installation of the rear view camera (not supplied) is required before use. The picture from a rear view camera connected to the CAMERA IN terminal is displayed when: - the back lamp of your car lights up (or the shift lever is set to the R (reverse) position). - you press HOME, then touch [Rear Camera]. 15GB

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
15
GB
Cautions
• It is extremely dangerous if the cord becomes
wound around the steering column or gearstick.
Be sure to keep it and other parts from interfering
with your driving operations.
• If airbags or any other shock-absorbing
equipment are in your car, contact the store where
you purchased this unit or the car dealer before
installation.
Notes
• When mounting on the dashboard, remove the visor clip
carefully from the microphone
, then attach the flat-
mount base
to the microphone
.
• Before attaching the double-sided tape
, clean the
surface of the dashboard with a dry cloth.
When using the steering wheel remote
control
Installation of the connection cable RC-SR1
is
required before use.
1
To enable the steering wheel remote control, select
[General]
[Steering Control]
[Custom]
to
make the registration.
When the registration is complete, the steering
wheel remote control becomes available.
Notes on installing the connection cable RC-SR1
• Refer to the support site for details then connect each lead
properly to the appropriate leads. Making an improper
connection may damage the unit.
• Consulting the dealer or an experienced technician for
help is recommended.
When using the wired remote control
1
To enable the wired remote control, set [Steering
Control] in [General] to [Preset].
Installation of an HDMI cable (not supplied) is
required before use.
1
Connect an HDMI cable to the HDMI
terminal at the back panel of the unit.
2
Pass the cable tie
through the cable
holder, then tie the cable tie
around the
HDMI cable.
The HDMI cable is secured to the unit.
* HDMI cable (not supplied)
3
Connect the installed HDMI cable to an
HDMI device.
4
Press HOME, then touch [HDMI].
The HDMI device connected will be mirrored to
this unit.
Installation of the rear view camera (not supplied) is
required before use.
The picture from a rear view camera connected to
the CAMERA IN terminal is displayed when:
– the back lamp of your car lights up (or the shift
lever is set to the R (reverse) position).
– you press HOME, then touch [Rear Camera].
Using the wired remote control
Using an HDMI device
Using the rear view camera
*