Sony XM-440EX Primary User Manual - Page 1
Sony XM-440EX - Stereo Power Amplifier Manual
View all Sony XM-440EX manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Troubleshooting Guide The following checklist will assist in the correction of most problems which you may encounter with your unit. Before going through the checklist below, refer to the connection and operating procedures. The POWER/PROTECTOR indicator does not light up. k The fuse is blown. t Replace the fuse with a new one. k The ground lead is not securely connected. t Fasten the ground lead securely to a metal surface of the car. k The voltage going into the remote terminal is too low. • The connected master unit is not turned on. t Turn on the master unit. • The system employs too many amplifiers. t Use a relay. k Check the battery voltage (10.5 - 16 V). The OVER CURRENT indicator lights up in red. kTurn off the power switch. The speaker outputs are short-circuited. t Rectify the cause of the shortcircuit. The OFFSET indicator lights up in red. k Turn off the power switch. Make sure the speaker cord and ground lead are securely connected. The THERMAL indicator lights up in red. k The unit heats up abnormally. • Use speakers with suitable impedance (2 to 8 ohms). • Make sure to place the unit in a well ventilated location. Alternator noise is heard. k The power connecting leads are installed too close to the RCA pin cords. t Keep the leads away from the cords. k The ground lead is not securely connected. t Fasten the ground lead securely to a metal surface of the car. k Negative speaker leads are touching the car chassis. t Keep the leads away from the car chassis. The sound is muffled. k The FILTER selector switch is set to the "LPF" position. The sound is too low. k The LEVEL adjustment control is set to the "MIN" position. No sound is heard. k The FILTER selector switch is settled between settings (i.e., not correctly set); set the switch properly. No test tone is heard when the TEST TONE button is pressed. k The wiring is not properly connected. t Check the connections and re-wire accordingly. 3-045-652-61 (1) Stereo Power Amplifier Operating Instructions Manual de instrucciones Guía de solución de problemas La siguiente lista de comprobaciones le resultará útil para solucionar la mayoría de los problemas que pueda encontrar con la unidad. Antes de consultar la siguiente lista, examine los procedimientos de conexión y funcionamiento. El indicador POWER/PROTECTOR no se ilumina. k El fusible se ha fundido. t Sustitúyalo por otro nuevo. k El cable de toma a tierra no está firmemente conectado. t Conéctelo firmemente a un punto metálico del automóvil. k La tensión que recibe el terminal remoto es demasiado baja. • No ha activado la unidad principal conectada. t Actívela • El sistema emplea demasiados amplificadores. t Utilice un relé. k Compruebe la tensión de la batería (10,5 - 16 V). El indicador OVER CURRENT se ilumina en color rojo. k Desactive el interruptor de alimentación. Las salidas de altavoz están cortocircuitadas. t Elimine la causa del cortocircuito. El indicador OFFSET se ilumina en color rojo. k Desactive el interruptor de alimentación. Compruebe que el cable de altavoz y el de toma a tierra están firmemente conectados. El indicador THERMAL se ilumina en color rojo. k La unidad se calienta de forma anómala. • Emplee altavoces con la impedancia adecuada (de 2 a 8 ohmios). • Asegúrese de colocar la unidad en un lugar bien ventilado. Se escucha ruido del alternador. k Los cables de conexión de alimentación se encuentran demasiado cerca de los cables de pines RCA. t Manténgalos alejados entre sí. k El cable de toma a tierra no está firmemente conectado. t Conéctelo firmemente a un punto metálico del automóvil. k Los cables negativos de altavoz han entrado en contacto con el chasis del automóvil. t Manténgalos alejados del chasis. El sonido se amortigua. k El interruptor de selección FILTER está ajustado en la posición "LPF". El sonido es demasiado bajo. k El control de ajuste de nivel LEVEL está ajustado en la posición "MIN". No se oye el sonido. k El interruptor de selección FILTER no está ajustado correctamente en una posición exacta; ajústelo adecuadamente. No se oye ningún tono de prueba al pulsar el botón TEST TONE. k El cableado no está adecuadamente conectado. t Compruebe las conexiones y configure el cableado acordemente. ‹G n ⁄UƒC ¸‹d" ƒ‡§U' , ¤M-z ifl „J¤ "" ˆD¡C ƒb¤ˇ¥˛⁄U›-"" ¸‹d" ⁄§«e¡A‰- ¸‹d‡s- 'M §@¤B˘J‹O§_¥¿‰T¡C XM-440EX Sony Corporation 2000 Printed in Korea Specifications Circuit system OTL (output transformerless) circuit Pulse power supply Inputs RCA pin jacks High level input connector Outputs Speaker terminals Speaker impedance 2 - 8 Ω (stereo) 4 - 8 Ω (when used as a bridging amplifier) Maximum outputs Four speakers: 80 W × 4 (at 4 Ω) 100 W × 4 (at 2 Ω) Two speakers: 200 W × 2 (at 4 Ω, when used as a bridging amplifier) Rated outputs (supply voltage at 14.4 V) Four speakers: 40 W × 4 (20 Hz - 20 kHz, 0.04 % THD, at 4 Ω) 50 W × 4 (20 Hz - 20 kHz, 0.1 % THD, at 2 Ω) Two speakers: 100 W × 2 (20 Hz - 20 kHz, 0.1 % THD, at 4 Ω) Frequency response 5 Hz - 100 kHz ( +0 -3 dB) Harmonic distortion 0.005 % or less (at 1kHz, 4 Ω) Input level adjustment range 0.2 - 4.0 V (RCA pin jacks) 0.4 - 8.0 V (High level input) High-pass filter 50 - 200 Hz, -12 dB/oct Low-pass filter 50 - 200 Hz, -12 dB/oct Power requirements 12 V DC car battery (negative ground) Power supply voltage 10.5 - 16 V Current drain at rated output: 24 A Remote input: 1.4 mA Dimensions Approx. 237 × 52 × 214 mm (w/h/d) not incl. projecting parts and controls Mass Approx. 1.9 kg not incl. accessories Supplied accessories Mounting screws (4), Terminal cap (1) Optional accessories Connecting cord for power amplifier RC-46 Design and specifications are subject to change without notice. POWER/PROTECTOR « ¥ ¿O¥...´I«G¡C y o„q ,`n¡C k «O I •‡Q¿N´_⁄Ft¡C§ ·«•s""«O I •¡C k „q•‰‡s- ‰uƒw,¸-o⁄ aR"CæA·¡- ‰u¡tC ¤ˇ„q•‰‰u k - ƒa ‰u¤Sƒ‡¤c'Tƒa‡s- t ƒn¡-CN- ƒa ‰u¤c'Tƒa'T u¡C Especificaciones 'wƒb¤T W¡C k ¶i⁄J»»--" ⁄l""„q £⁄ §C¡C • ‡s- ""¥D ¤Sƒ‡¥·¶t}¡C¥·¶}¥D ¡C • ¥»¤t h'æ⁄j t„¡¤Cˇ¥˛˜~„q „¡C k ¸‹d„qƒ „q £1¡0].5- 16 V¡^¡C k - ƒa ‰u¤Sƒ‡¤c'Tƒa‡s- t ƒn¡-CN- ƒa ‰u¤c'Tƒa'T'w ƒb¤T W¡C k ›t·›`n „ ‰u- ˜†⁄F¤T¤fi'‡t‰L¤¡ˇC‡o¤˙ ‰u»•´ ¤T L¡C Sistema de circuito Entradas OTL (salida sin transformador) Suministro de alimentación por impulsos Tomas de pines RCA Conector de entrada de alto nivel OVER CURRENT « ¥ ¿O¥H‹ıƒ ´I«G¡C k q C·›`n „¿Ø¥X u,t⁄F¡¸C‹d u C ‡Qfił› ¡C k FILTER¿ „¶}ˆ ‡Q‡]'wƒLbP¡F§¡¤ƒ ,m¡C Salidas Terminales de altavoz Impedancia de altavoz 2 - 8 Ω (estéreo) `n› ⁄ §C¡C 4 - 8 Ω (si se utiliza como OFFSET « ¥ ¿O¥H‹ıƒ ´I«G¡C k LEVEL Q‡]'wƒbM¡I§N¡¤ ¡C k q C‰T«H·›`n „„q•‰‰u'M- ƒa ‰u‡s- ¤c'T¡C Salidas máximas amplificador en puente) Cuatro altavoces: THERMAL « ¥ ¿O¥H‹ıƒ ´I«G¡C k a o... ¡C A n 2„-¡]8Ω¡^¡C • ⁄@'w›n-N¥» 'æ,mƒb‡q›•¤}ƒn""ƒ ,m¡C n› ¡C k FILTER Q'æƒb¤ › ‡]'w p¡G⁄£¥¿-' ‡]'w¡^¡F-N¶}ˆ A• ƒa‰ ªƒn¡C 80 vatios × 4 (a 4 Ω) 100 vatios × 4 (a 2 Ω) Dos altavoces: 200 vatios × 2 (a 4 Ω, si se utiliza • TEST TONE ` ‡Q« ⁄Ufi ¡A C como amplificador en puente) Salidas nominales (tensión de suministro a 14,4 V) k „q‰u‡s- ⁄£ƒnt¡C ¸‹d- ‰u¡A a›«•s- ‰u¡C Cuatro altavoces: 40 vatios × 4 (20 Hz - 20 kHz, 0,04 % THD, a 4 Ω) 50 vatios × 4 (20 Hz - 20 kHz, 0,1 % THD, a 2 Ω) Dos altavoces: 100 vatios × 2 (20 Hz - 20 kHz, 0,1 % THD, a 4 Ω) Respuesta de frecuencia 5 Hz - 100 kHz ( +0 -3 dB) Fuse Replacement Sustitución del fusible If the fuse blows, check the power connection and replace the fuse. If the fuse blows again after replacement, there may be an internal malfunction. In such a case, consult your nearest Sony dealer. Warning When replacing the fuse, be sure to use one matching the amperage stated above the fuse holder. Never use a fuse with an amperage rating exceeding the one supplied with the unit as this could damage the unit. § ·««O I • Si el fusible se funde, compruebe la conexión de alimentación y sustitúyalo. Si el fusible se funde de nuevo después de sustituirlo, es posible que exista un fallo de funcionamiento interno. En este caso, póngase en contacto con el proveedor Sony más próximo. Advertencia Al sustituir el fusible, asegúrese de utilizar uno cuyo amperaje coincida con el especificado en el portafusible. No utilice nunca un fusible con un amperaje superior al del suministrado con la unidad, ya que podría dañarla. ›Y«O I •¿N´_¡A‰- ¸‹d„q•‰‡s O I •¡C›Y «O I S‡Q¿N´_¡A«h¥ifl ‹O⁄"‡¡‹G» ¡Cƒb‡o" -¡ "p⁄U¡A‰-ƒV-´z‡ "æ""Sony,g P ¿ , ¡C ˜ §i O I •fi ¡A›n‰T«O¤ˇ¥˛»P«O I •" fiy⁄W‡W'w ƒw P""«O I •¡C B'wƒw ...˘¶W„L¥» " -a«O I •ƒw ...˘""«O I •¡A§_«h•|•lˆa¥» ¡C ‡Wfi „q, ¤t†˛ OTL¡] L X¡^„q, fl ˚„q•‰ ¿Ø⁄J RCA f "„q¥›¿Ø⁄J‡s- „ ¿Ø¥X ·›`n „" ⁄l ·›`n „" § 2 - 8 n¡^ 4 - 8 j „fi ¡^ ‡ ⁄j¿Ø¥X 4 › ·›`n „¡G 80 W× 4¡]ƒb 4Ω fi ¡^ 100 W× 4¡]ƒb 2Ω fi ¡^ 2 › ·›`n „¡G 200 W× 2¡]ƒb 4Ω¡A ⁄j „fi ¡^ ˆB'w¿Ø¥X¡1]4.4 fiV ""„q•‰„q £¡^ 4 › ·›`n „¡G 40 W× 4¡]20 Hz- 20 kH¡zA0.04 % THD ¡Aƒb 4Ω fi ¡^ 50 W× 4¡]20 Hz- 20 kH¡zA 0.1 % THD ¡Aƒb 2Ω fi ¡^ 2 › ·›`n „¡G 100 W× 2¡]20 Hz- 20 kH¡zA0.1 % W†v´Q ‡ THD ¡Aƒb 4Ω fi ¡^ 5 Hz- 100 kH¡z]+-30 ¡d^B Distorsión armónica 0,005 % o inferior (a 1kHz, 4 Ω) Margen de ajuste de nivel de entrada 0,2 - 4,0 V (Tomas de pines RCA) 0,4 - 8,0 V (Entrada de alto nivel) Filtro de paso alto 50 - 200 Hz, -12 dB/oct Filtro de paso bajo 50 - 200 Hz, -12 dB/oct Requisitos de alimentación Batería de automóvil de 12 V CC (negativo a masa) Tensión de suministro de alimentación 10,5 - 16 V Consumo de energía Con salida nominal: 24 A Entrada remota: 1,4 mA Dimensiones Aprox. 237 × 52 × 214 mm (an/al/prf), partes y controles salientes excluidos Masa Aprox. 1,9 kg accesorios excluidos Accesorios suministrados Tornillos de montaje (4) Cubierta terminal (1) Accesorios opcionales Cable de conexión para amplificador de potencia RC-46 Diseño y especificaciones sujetos a cambios sin previo aviso. ¿ "i¥¢flu 0.005 '%˛⁄ ' 0.005 % ¡]ƒb 1kH¡zA4 Ω fi ¡^ ¿Ø⁄J„q 0.2- 4.0 ¡V]RCA f¡^ 0.4- 8.0 ¡V] "„q¥›¿Ø⁄J¡^ "‡q´o"i „ 50- 200 H¡zA- 12 dB/oct §C‡q´o"i „ 50- 200 H¡zA- 12 dB/oct „q•‰ 12 V"‰‹y„q¤T¤fi„qƒ ¡]›t- ƒa¡^ „q•‰„q £ 10.5- 16 V „q‹y"|•¥ˆB'w¿Ø¥X ƒbˆB'w¿Ø¥Xfi 2¡4G A J¡1G.4 mA ⁄ ⁄o ‹ø 237× 52× 214 mm ¡]...e A ⁄£¥]‹A¥Y¥X‡¡⁄ 'M--¤ „¡C ›«¶q ‹ø 1.⁄9‰⁄ ¡A⁄£¥]‹A" ¥ ¡C ƒw v(4) " ⁄l»\·U(1) ¿ "¥ ¥\†v'æ⁄j „RC-46¥˛‡s- ‰u¡C ‡]›p""‡Wfi ›Y A tƒ ‡q" ¡C