TP-Link T1500-28PCT TL-SL2428P T1500-28PCT V1 Quick Install Guide
TP-Link T1500-28PCT TL-SL2428P Manual
View all TP-Link T1500-28PCT TL-SL2428P manuals
Add to My Manuals
Save this manual to your list of manuals |
TP-Link T1500-28PCT TL-SL2428P manual content summary:
- TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 1
Business Networking Solution Installation Guide Smart PoE Switch T1500-28PCT (TL-SL2428P) - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 2
- TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 3
without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 4
the official Website: http://www.tp-link.com About this Installation Guide This Installation Guide describes the hardware characteristics, installation methods the switch. Chapter 5 Login to the Switch. This chapter instructs you to login to the switch via Web Interface. Appendix A Troubleshooting. - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 5
the specific formats to highlight special messages. The following table lists the notice icons that are used throughout this guide. Remind to be careful. A caution indicates a potential which may result in device damage. Remind to take notice. The note contains the helpful information for a better - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 6
Smart PoE Switch Contents Chapter 1 1.1 1.2 Introduction 01 Product Overview 01 Appearance 01 Chapter 2 2.1 2.2 2.3 17 Power On 17 Initialization 17 Chapter 5 Login to the Switch----------- 18 Appendix A Troubleshooting 19 Appendix B Hardware Specifications--------- 20 IV Contents - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 7
can fully meet the need of the users demanding higher networking performance. T1500-28PCT Smart PoE Switch is also a Power Sourcing Equipment (PSE*). All the fast Ethernet RJ45 ports on the switch support Power over Ethernet (PoE*) function, which can automatically detect and supply power with those - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 8
Smart PoE Switch LEDs T1500-28PCT has an LED mode switch button which is for switching the LED status indication. When the 10/100M LED is on, the port LED is indicating the data transmission rate. When the PoE LED is on, the port LED is indicating the power supply status. By default, the 10/100M - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 9
Overload or short circuit is detected Power-on self-test has failed No PoE power supply is provided on the port A 1000Mbps device is connected to 10/100Mbps RJ45 Port 10/100/1000Mbps RJ45 Port T1500-28PCT 24 4 SFP Port 2 Reset With the switch powered on, press Reset button for 5 seconds to - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 10
Smart PoE Switch ■■ Rear Panel The rear panel of T1500-28PCT is shown as Figure 1-2. Kensington Security Slot Power Socket Grounding Terminal Figure 1-2 Rear Panel of T1500-28PCT Kensington Security Slot Secure the lock (not provided) into the security slot to prevent the device from being stolen - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 11
Chapter 2 Installation Smart PoE Switch 2.1 Package Contents Make sure that the package contains the following items. If any of the listed items is damaged or missing, please contact your distributor. One Switch One Power Cord This Installation Guide 51$5 4NBSU1P&4XJUDI 183 4:4 1P - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 12
Smart PoE Switch ■■ Site Requirements To ensure normal operation and long service life of the device, please install it in circuit board. To avoid the effect of static electricity on the operation of the switch, please attach much importance to the following items: ■■ Dust the device regularly, and - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 13
Smart PoE Switch ■■ Keep the device far from high-frequency, strong-current devices, , please note the following items: ■■ The rack or workbench is flat and stable, and sturdy enough to support the weight of 5.5kg at least. ■■ The rack or workbench has a good ventilation system. The equipment room - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 14
Smart PoE Switch ■■ ESD-preventive steps: 1. Set the device on a flat surface strong enough to support the entire weight of the device with all fittings. 2. Remove device in an EIA standard-sized, 19-inch rack, follow the instructions described below: 1. Check the grounding and stability of the rack - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 15
Smart PoE Switch Rackmounting Bracket Screw Figure 2-2 Bracket Installation 3. After the brackets are attached to the device, use suitable screws (not provided) to secure the brackets to the - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 16
Smart PoE Switch Chapter 3 Lightning Protection 3.1 Cabling Reasonably In the actual network environment, you may need cable outdoors and indoors, and the requirements for cabling outdoors and indoors - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 17
Smart PoE Switch ■■ Requirements for Cabling Indoors When cabling indoors, keep a certain between Ethernet cable and other pipelines are shown in the table. Other Pipelines Down-conductor PE Service pipe Compressed air pipe Thermal pipe (not wrapped) Thermal pipe (wrapped) Gas pipe Ethernet Cable - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 18
Smart PoE Switch Cable Pave Way 2~5kVA powerline >5kVA powerline Parallel cabling One body from electric shock. In different environments, the device may be grounded differently. The following will instruct you to connect the device to the ground in two ways, connecting to the grounding bar or - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 19
Smart PoE Switch Note: The grounding bar and the ground cable are not provided with our product. If needed, please self purchase them. ■■ Connecting to the Ground via - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 20
Smart PoE Switch Grounding Terminal Ground Cable Equipotential Bonding Cable Grounding Bar Figure 3-3 Equipotential Bonding When equipotential bonding, please note that the cable should be copper conductor with a - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 21
Smart PoE Switch ■■ The port rate of the signal lightning arrester should match the rate of the desired port on the device. If it is not matched, this - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 22
in a slot and has a valid link on the port, the associated RJ45 port will be disabled and cannot be used. SFP Port SFP Module Figure 4-2 Connecting the LAN Port Note: ■■ SFP module supports hot-plugging, plug the SFP module into the SFP port and the switch can identify it automatically. ■■ The SFP - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 23
Smart PoE Switch 4.3 Verify Installation After completing the installation, please verify the following items: ■■ There are 5~10cm of clearance around the sides of the device for ventilation and - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 24
Smart PoE Switch Chapter 5 Login to the Switch 1. To access the GUI of the switch, open a web browser switch. The IP address is 192.168.0.x ("x" is any number from 2 to 254), Subnet Mask is 255.255.255.0. For the detailed instructions as to how to do this, please refer to Appendix B in the User Guide - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 25
Appendix A Troubleshooting Smart PoE Switch Q1. What could I do if I forgot the username and password of the switch? With the switch powered on the voltage of the power supply meets the requirement of the input voltage of the switch. Q3. What could I do if I could not access the web-based - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 26
Smart PoE Switch Appendix B Hardware Specifications Item Content Standards and Protocol IEEE 802.3i 10Base-T IEEE 802.3u 100Base-TX/100Base-FX IEEE 802.3ab 1000Base-T IEEE802.3ad Link Aggregation IEEE 802.3z 1000Base-X IEEE 802.3x Flow Control IEEE802.1p QoS IEEE802.1q VLAN IEEE802.1d - TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 27
- TP-Link T1500-28PCT TL-SL2428P | T1500-28PCT V1 Quick Install Guide - Page 28
Website: http://www.tp-link.com E-mail: [email protected] 7106505196 REV1.0.0
Installation Guide
Smart PoE Switch
T1500-28PCT (TL-SL2428P)
Business Networking Solution