TP-Link T1500G-10PSTL-SG2210P T1500G-10PSUN V1 Intallation Guide - Page 2
Frequently Asked Questions FAQ, Specifications
View all TP-Link T1500G-10PSTL-SG2210P manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Specifications General Specifications Standard IEEE802.3i, IEEE802.3u, IEEE802.3ab, IEEE802.3ad, IEEE802.3af, IEEE802.3x, IEEE802.1p, IEEE802.1q, IEEE802.1d, IEEE802.1s, IEEE802.1w, IEEE802.3z Protocol CSMA/CD Data Transfer Rate Ethernet:10Mbps (Half Duplex) 20Mbps (Full Duplex) Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) Gigabit Ethernet: 2000Mbps (Full Duplex) Network Media (Cable) 10Base-T: UTP Cat. 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100Ȥ STP (maximum 100m) 100Base-TX: UTP of Cat. 5 or above (maximum 100m) EIA/TIA-568 100Ȥ STP (maximum 100m) 1000Base-T: UTP of Cat. 5e or above (maximum 100m) EIA/TIA-568 100Ȥ STP (maximum 100m) Number of Ports 8 10/100/1000Mbps Auto-Negotiation RJ45 ports and 2 SFP slots PoE Ports (RJ45) PoE Ports: Port1-Port8 Total Power Supply: 53W LED Indicators Power, System, Link/Act, PoE MAX, PoE Status, SFP1, SFP2 Transfer Method Store and Forward MAC Address Learning Automatically learning, automatically aging Frame Filter Rate 10Base-T: 14881pps/Port 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port Frame Forward Rate 10Base-T: 14881pps/Port 100Base-Tx: 148810pps/Port 1000Base-T: 1488095pps/Port Environmental and Physical Specifications Operating Temperature 0˚C to 40˚C (32˚F to 104˚F) Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F) Operating Humidity 10% to 90% non-condensing Storage Humidity 5% to 90% non-condensing Frequently Asked Questions (FAQ) Q1. The Power LED is not lit. The Power LED should be lit when the power system is working normally. If the Power LED is not lit, please check as follows: A1: Make sure the AC power cord is connected to the switch with power source properly. A2: Make sure the voltage of the power supply meets the requirements of the input voltage of the switch. A3: Make sure the power source is ON. Q2. Why is the Link/Act LED not lit while a device is connected to the corresponding port? Please try the following: A1: Make sure that the cable connectors are firmly plugged into the switch and the device. A2: Make sure the connected device is turned on and works normally. A3: Try to change the connected device's transmission speed and duplex mode. A4: The cable must be less than 100 meters long (328 feet). Q3. Why are some ports not supplying power for PoE devices? Please try the following: A1: Make sure that this PoE device complies with IEEE 802.3af/IEEE 802.3at. A2: Try another PoE port on the switch. A3: Pay attention to PoE priority. If the total power consumption of PoE powered devices exceeds 53W, a priority will be set among the ports. Ports with a smaller port number will have higher priority. For example, Port 1, 2 and 5 are each consuming 15.4W. If an additional powered device consuming 12W is connected to Port 3, then the switch will cut off power to Port 5 because of the overload. For technical support and other information, please visit http://www.tp-link.com/support FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. SAFETY NOTICES Cautions Do not use this product near water, for example, in a wet basement or near a swimming pool. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. CE Mark Warning This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. BSMI Notice b b a b b b b b b b A VCCI-A Explanation of the symbols on the product label DC voltage RECYCLING This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment. User has the choice to give his product to a competent recycling organization or to the retailer when he buys a new electrical or electronic equipment Industry Canada Statement CAN ICES-3 (A)/NMB-3(A) © 2017 TP-Link