Toshiba 65NH84 Owners Manual - Page 27

Adding channels to the TV's memory

Get Toshiba 65NH84 PDF manuals and user guides View all Toshiba 65NH84 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Introduction Connecting your TV Using the Remote Control Adding channels to the TV's memory When you press Channel y or z, your TV will stop only on the channels stored in the TV's channel memory. Follow the steps below and on the next page to program all active channels into the TV's memory. Programming channels automatically Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are stored automatically, you can manually add or erase individual channels (see page 28). To program channels automatically: 1. Press MENU, and then press x or • until the SET UP menu appears. 2. Press y or z until the TV/CABLE is highlighted, and then press ENTER to display the pull-down menu. 3. Press y or z to highlight either TV or CABLE, depending on which you use. If you use an antenna, highlight TV; if you use cable, highlight CABLE. LANGUAGE CLOCK SET ANT 1 / 2 TV / CABLE CH PROGRAM ADD / ERASE SET UP : SELECT ENTER : SET TV CABLE 4. Press ENTER. 5. Press z to select CH PROGRAM. Note: To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control. TV CABLE/SAT POWER LIGHT SLEEP VCR DVD 123 AUDIO1 AUDIO2 MODE 456 789 S PIC SIZE ACTION MENU GUIDE ETUP +10 100/ 0 ENT INFO FAVORITE TLHINEKATER TITLE SUB TITLE FAV AUDI O ENTER FAV CH VOL EXIT DVD RTN DVD CLEAR CH RTN INPUT RECALL MUTE SLOW/DIR SKIP/SEARCH MENU ENTER yzx • Channel yz LANGUAGE CLOCK SET ANT 1 / 2 TV / CABLE CH PROGRAM ADD / ERASE SET UP ENGLISH 00:00 ANT1 CABLE ADD : MOVE ENTER : START 6. Press ENTER to start channel programming. The TV will automatically cycle through all the TV or Cable channels (depending on which you selected), and store all active channels in the channel memory. While the TV is cycling through the channels, the message "Programming Now-Please Wait" appears. 7. When channel programming is complete,the message "Completed" appears. 8. Press Channel y or z to view the programmed channels. Setting up your TV Using the TV's Features Appendix Index 27 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Introduction
Connecting
your TV
Using the
Remote Control
Setting up
your TV
Using the TV’s
Features
Appendix
Index
27
Adding channels to the TV’s memory
When you press Channel
y
or
z
, your TV will stop only on the
channels stored in the TV’s channel memory.
Follow the steps below and on the next page to program all active
channels into the TV’s memory.
Programming channels automatically
Your TV can automatically detect all active channels in your area and
store them in its memory. After the channels are stored automatically,
you can manually add or erase individual channels (see page 28).
To program channels automatically:
1.
Press MENU, and then press
x
or
•
until the SET UP menu
appears.
2. Press
y
or
z
until the TV/CABLE is highlighted, and then press
ENTER to display the pull-down menu.
3. Press
y
or
z
to highlight either TV or CABLE, depending on
which you use. If you use an antenna, highlight TV; if you use
cable, highlight CABLE.
LANGUAGE
SET
UP
CLOCK
SET
TV
CABLE
ANT
1 / 2
TV / CABLE
CH
PROGRAM
ADD / ERASE
SELECT
:
:
SET
ENTER
4.
Press ENTER.
5. Press
z
to select CH PROGRAM.
LANGUAGE
SET
UP
CLOCK
SET
00:00
ENGLISH
ANT
1 / 2
ANT1
TV / CABLE
CABLE
ADD
CH
PROGRAM
ADD / ERASE
MOVE
:
:
START
ENTER
6.
Press ENTER to start channel programming. The TV will
automatically cycle through all the TV or Cable channels
(depending on which you selected), and store all active channels
in the channel memory.
While the TV is cycling through the channels, the message
“Programming Now—Please Wait” appears.
7.
When channel programming is complete,the message
“Completed” appears.
8.
Press Channel
y
or
z
to view the programmed channels.
1
2
3
4
5
6
7
8
9
100/
0
ENT
POWER
+10
ACTION
MODE
PIC SIZE
MENU
LIGHT
SLEEP
ENTER
FAV
CH
VOL
EXIT
CH RTN
DVD RTN
DVD CLEAR
SLOW/DIR
SKIP/SEARCH
INPUT
RECALL
MUTE
L
I
N
K
T
H
E
A
T
E
R
F
A
V
O
R
I
T
E
I
N
F
O
G
U
I
D
E
S
E
T
U
P
T
I
T
L
E
S
U
B
T
I
T
L
E
A
U
D
I
O
FAV
TV
CABLE/SAT
VCR
DVD
AUDIO1
AUDIO2
MENU
yzx
•
Channel
yz
Note:
To tune the TV to a channel not programmed
in the channel memory, you must use the
Channel Number buttons on the remote
control.
ENTER
Downloaded from
www.Manualslib.com
manuals search engine