Toshiba DR570KU Owner's Manual - English - Page 11

Introduction Connections Basic Setup FUNCTIONAL OVERVIEW Front Panel 1 2 3* 4 5 6 7 8 DR570 (*) The unit can also be turned on by pressing these buttons. 1. I/y ON/STANDBY button • Press to turn on the unit, or to turn the unit into the standby mode. (To completely shut down the unit, you must unplug the AC power cord.) • If timer programmings have been set, press to set the unit to timer-standby mode. 2. Disc tray • Place a disc when the disc tray is opened. 3. A OPEN/CLOSE button* • Press to open or close the disc tray. 4. Infrared sensor window • Receive signals from your remote control so that you can control the unit from a distance. 5. SKIP H button • During playback, press once midway through a chapter or track to go back to the beginning of the current chapter or track. When pressed twice in quick succession, playback will start from the preceding chapter or track. • During playback, press and hold for 1.5 seconds to fast reverse. • When playback is paused, press to play back reverse step by step. • When playback is paused, press and hold for 1.5 seconds to slow reverse. 6. SKIP G button • During playback, press to skip to the next chapter or track. • During playback, press and hold for 1.5 seconds to fast forward. 15 14* 13 12 11 10 9 • When playback is paused, press to play back advance step by step. • When playback is paused, press and hold for 1.5 seconds to slow forward. 7. Display • Refer to "FRONT PANEL DISPLAY GUIDE" on page 17. 8. HDMI indicator • Lights up and indicates the HDMI video resolution when HDMI output is on. 9. DV IN jack (L3) • Use to connect the DV output of external device with a DV cable. 10. AUDIO input jacks (L2) • Use to connect external device with an RCA audio cable. 11. VIDEO input jack (L2) • Use to connect external device with an RCA video cable. 12. S-VIDEO input jack (L2) • Use to connect the S-video output of external device with an S-video cable. 13. I REC button • Press once to start a recording. Press repeatedly to start one-touch timer recording. 14. B PLAY button* • Press to start or resume playback. 15. C STOP button • Press to stop playback or recording. Rear Panel 1 2 34 5 6 Disc Management Recording Playback Editing Function Setup 12 11 10 9 8 7 1. ANTENNA IN jack • Use to connect an antenna. 2. VIDEO IN jack (L1) • Use to connect external device with an RCA video cable. 3. VIDEO OUT jack • Use to connect a TV monitor, AV receiver or other device with an RCA video cable. 4. COMPONENT VIDEO OUT jacks • Use to connect a TV monitor with component video inputs with a component video cable. 5. HDMI OUT jack • Use an HDMI cable to connect to a display with an HDMI compatible port. 6. AC Power Cord • Connect to a standard AC outlet to supply power to this unit. • Unplug this cord from the AC outlet to completely shut down the unit. 7. COAXIAL DIGITAL AUDIO OUTPUT jack • Use to connect an AV receiver, Dolby Digital decoder, DTS decoder or other device with a digital audio coaxial input jack with a digital audio coaxial cable. 8. S-VIDEO OUT jack • Use to connect the S-video input of a TV monitor, AV receiver or other device with an S-video cable. 9. AUDIO OUT jacks • Use to connect a TV monitor, AV receiver or other device with an RCA audio cable. 10. S-VIDEO IN jack (L1) • Use to connect the S-video output of external device with an S-video cable. 11. AUDIO IN jacks (L1) • Use to connect external device with an RCA audio cable. 12. ANTENNA OUT jack • Use to connect an RF coaxial cable to pass the signal from the ANTENNA IN to your TV. Note • Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit. • This unit does not have the RF modulator. EN 11 Others &4$6%@%3,6@&/@WJOEE