Toshiba Satellite P100 User Manual - Page 90

Disconnecting, LAN, Connecting the LAN cable

Get Toshiba Satellite P100 PDF manuals and user guides View all Toshiba Satellite P100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Operating Basics Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. LAN The computer is equipped with LAN circuits that support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX), or Gigabit Ethernet LAN (1000megabits per second, 1000BASE-T). This section describes how to connect/disconnect to and from a LAN. If you use Gigabit Ethernet LAN (1000megabits per second, 1000BASE-T), be sure to connect with CAT5e OR CAT6 cable. Do not install or remove an optional memory module while Wake-up on LAN is enabled. Wake-up on LAN does not work without the AC adapter. Leave it connected, if you are using this feature. Connecting the LAN cable The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer's default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASETX), be sure to connect with a CAT5 cable. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with either a CAT5 or a CAT3. If you use Gigabit Ethernet LAN (1000megabits per second, 1000BASE-T), be sure to connect with CAT5e OR CAT6 cable. To connect the LAN cable, follow the steps below. 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. 4-14 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
4-14
User’s Manual
Operating Basics
Disconnecting
To disconnect the internal modem cable, follow the steps below.
1.
Pinch the lever on the connector in the telephone jack and pull out the
connector.
2.
Disconnect the cable from the computer in the same manner.
LAN
The computer is equipped with LAN circuits that support Ethernet LAN (10
megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits
per second, 100BASE-TX), or Gigabit Ethernet LAN (1000megabits per
second, 1000BASE-T). This section describes how to connect/disconnect
to and from a LAN.
If you use Gigabit Ethernet LAN (1000megabits per second, 1000BASE-T),
be sure to connect with CAT5e OR CAT6 cable.
Connecting the LAN cable
If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-
TX), be sure to connect with a CAT5 cable. You cannot use a CAT3 cable.
If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you
can connect with either a CAT5 or a CAT3.
If you use Gigabit Ethernet LAN (1000megabits per second, 1000BASE-T),
be sure to connect with CAT5e OR CAT6 cable.
To connect the LAN cable, follow the steps below.
1.
Turn off the power to the computer and to all external devices
connected to the computer.
2.
Plug one end of the cable into the LAN jack. Press gently until you hear
the latch click into place.
Do not install or remove an optional memory module while Wake-up on
LAN is enabled.
Wake-up on LAN does not work without the AC adapter. Leave it
connected, if you are using this feature.
The computer must be configured properly before connecting to a LAN.
Logging onto a LAN using the computer's default settings could cause a
malfunction in LAN operation. Check with your LAN administrator
regarding set-up procedures.