ViewSonic PJ-WMK-007 Quick Start Guide
ViewSonic PJ-WMK-007 Manual
 |
View all ViewSonic PJ-WMK-007 manuals
Add to My Manuals
Save this manual to your list of manuals |
ViewSonic PJ-WMK-007 manual content summary:
- ViewSonic PJ-WMK-007 | Quick Start Guide - Page 1
and contact a qualified service personnel immediately. 10. Only supported nor recommended, may cause property damage or personal injury, and shall be at the sole risk of users/installers. PJ-WMK-007 Quick Start Guide 中国 http://www.viewsonic.com.cn 电话：4008 988 188 香港 http://www.hk.viewsonic
-
1
 |
 |
PJ-WMK-007
Quick Start Guide
Projector Mounting
Plate x 1
Setting Plate x 1
Ceiling Plate Cover x 1
Mounting Arm x 4
* Screw G has been lockd
on the mount.
B
NO
C
D
E
A
5
5
1
F
G
Screw
(
M6X55
)
Φ10mm
Anchor bolt
Allen key
4
Screw
(
M4X8
)
(
M5X12
)
diagrammatic
presentation
designation
quantity
Screw
M5 nuts
4
Screw
(
M4X10
)
4
4
中国
电话：
4008 988 188
香港
電話：
852 3102 2900
澳門
電話：
853 2840 3687
台灣
電話：
0800 899 880
한국
Phone: 080 333 2131
Singapore/Malaysia/Thailand
Phone: 65 6461 6044
India
Phone: 1800-419-0959
United States
Phone: 1-800-688-6688
Canada
Phone: 1-866-463-4775
Europe
Australia/New Zealand
Phone: 1800 880 818 (AUS)
0800 008 822 (NZ)
South Africa
Latin America (Chile)
Latin America (Mexico)
Latin America (Peru)
Latin America (Argentina)
Puerto Rico & Virgin Islands
Phone: 1-800-688-6688 (English)
PJ-WMK-007_QSG_Rev. 1b 01-06-21
Copyright © 2021 ViewSonic Corporation. All rights reserved.
Checking The Supplied Accessories
To Set The Projector Ceiling Mount On The Wall
To Set The Projector Ceiling Mount On The Wall
To Install The Projector On The Projector Ceiling Mount
To Set The Projector Ceiling Mount On The Wall
To Adjust Mounting Position
To Adjust The Horizontal Roll
To Remove The Projector Ceiling Mount
To Adjust The Horizontal Rotation
Product Information
Important Safety
To Adjust The Upward/Downward Slide
To Adjust The Vertical Tilt
1
2
3
4
6
5
Loose the G screws and remove
the projector mounting plate
Loose the screws and
remove the bracket
Assy from projector
ceiling mount
Remove the ceiling
plate cover
A
C
To thread the power cable and
other cables from the AL pipe
Center Line
Wooden Stud
CAUTION:
Make sure both
mounting holes are
on center line of
the stud.
>55mm
ø3mm
>55mm
ø
10~11mm
B
Concrete ceiling mounting
Use anchor bolt
Dry-ceiling mounting
Not use anchor bolt
●
Concrete ceiling mounting thickness must be a minimum 100mm. Anchor bolt and
sсrew (M6 × 55) are needed to be used for installation.
●
Dry-ceiling mounting thickness must be a minimum 70mm. Only sсrew (M6 × 55) is
needed to be used for installation. If the wall is not strong enough, reinforce it suf
ficiently before installation.
●
Please contact reseller if you have any questions about mounting surface issue.
Projector Mounting
Plate
Extend Arm
Extra screws and anchor bolt are backup
D
F
E
E
or
3
0
°
The angle of the ceiling wall is not more
than 30
°
Connect the power cable and
other cablesto the projector.
Adjustment direction
Adjustment direction
Adjustment buttons
A
B
Adjustment buttons
Adjustment direction
Adjustment buttons
A
B
A
B
A
B
Adjust the leftward/
Adjustment direction
Move the projector mounting plate and adjust the leftward/rightward slide.
Use a stick or something hard to pry open the ceiling plate cover.
-rightward slide
A
B
A
B
A
B
A
B
A
Locking screws
Adjustment direction
B
A
B
A
B
A
B
A
C
stick
Product W
eight
4.6 lb (2.1 Kg)
Max W
eight Load
55.1 lb (25 Kg)
500mm-780mm(from mounting plate center to the screen)
Adjustable Range
Adjustable
Angle
± 5° tilt, left\right, front\rear and lateral rotation adjustment
Model
PJ-WMK-007
Screw D Tightening torque: 8kgf-cm (
≦
12kgf-cm)
1.
Please read this manual carefully and follow all safety rules before installa�on.
2.
For safety reasons, please make sure the wall is strong enough to sustain the weight of the projector & wall
mount.
3.
The total maximum weight of all items mounted should NEVER exceed the weight capacity: 55 lbs (25kg).
4.
DO NOT a±empt to alter or modify any part of the wall mount or its a±achments.
5.
Do not install the projector wall mount on a structure that is prone to vibra�on, movement or chance of impact.
6.
To avoid risk of fire, do not install the projector with the projector wall mount in a humid or excessively dusty
place.
7.
Use the supplied accessories only. Use of accessories other than those supplied may result in damage to the
projector and/or projector wall mount.
8.
Unplug the AC power cord and any other connected cables before dismounting the projector from the projector
wall mount.
9.
Do not hit or hang any heavy objects on the projector wall mount. If the projector wall mount is damaged, stop
using immediately and contact a qualified service personnel immediately.
10. Only install the projector wall mount horizontally on the level surfaces.
* The manufacturer is not liable for any damages or injury caused by mishandling or improper installa�on.
11. The projector or wall mount may fall and cause personal injury. Ensure screws are tightened to the proper torque
after installation and any adjustments. Do not overtighten screws as this may cause screw deformation.
12. This wall mount kit ONLY supports ViewSonic® projectors and models that are designated by ViewSonic. Use with
non-ViewSonic branded projectors or exceeding the weight capacity is neither supported nor recommended,
may cause property damage or personal injury, and shall be at the sole risk of users/installers.
G
G
PJ-WMK-007
Quick Start Guide