ViewSonic PJ-WMK-007 Quick Start Guide - Page 1

PJ-WMK-007 Quick Start Guide Checking The Supplied Accessories Setting Plate x 1 Projector Mounting Plate x 1 NO diagrammatic presentation designation quantity A Screw(M6X55) 5 B Φ10mm Anchor bolt 5 C Allen key 1 D Screw(M4X8) 4 E Screw(M5X12) 4 F M5 nuts 4 G Screw(M4X10) 4 Ceiling Plate Cover x 1 Mounting Arm x 4 * Screw G has been lockd on the mount. To Set The Projector Ceiling Mount On The Wall Loose the screws and remove the bracket Assy from projector ceiling mount Remove the ceiling plate cover To Set The Projector Ceiling Mount On The Wall ● Concrete ceiling mounting thickness must be a minimum 100mm. Anchor bolt and sсrew (M6 × 55) are needed to be used for installation. ● Dry-ceiling mounting thickness must be a minimum 70mm. Only sсrew (M6 × 55) is needed to be used for installation. If the wall is not strong enough, reinforce it suf ficiently before installation. ● Please contact reseller if you have any questions about mounting surface issue. ø10~11mm ø3mm >55mm B >55mm Use anchor bolt Concrete ceiling mounting Not use anchor bolt Dry-ceiling mounting Wooden Stud Center Line To thread the power cable and other cables from the AL pipe A C CAUTION: Make sure both mounting holes are on center line of the stud. To Set The Projector Ceiling Mount On The Wall The angle of the ceiling wall is not more than 30° 30° Extra screws and anchor bolt are backup To Install The Projector On The Projector Ceiling Mount Projector Mounting F Plate or Extend Arm E E D G Loose the G screws and remove the projector mounting plate Screw D Tightening torque: 8kgf-cm (Ù12kgf-cm) To Adjust Mounting Position 1 Move the projector mounting plate and adjust the leftward/rightward slide. Adjust the leftward/ -rightward slide AB A B A B Adjustment direction G To Adjust The Vertical Tilt 2 Connect the power cable and other cablesto the projector. A B Adjustment buttons A B Adjustment direction To Adjust The Horizontal Roll 3 AB A B Adjustment buttons Adjustment direction To Adjust The Horizontal Rotation 4 A BA B Adjustment buttons Adjustment direction To Adjust The Upward/Downward Slide 5 A A B Locking screws B A B Adjustment direction To Remove The Projector Ceiling Mount 6 Use a stick or something hard to pry open the ceiling plate cover. stick A C Product Information Model Product Weight Max Weight Load Adjustable Range Adjustable Angle PJ-WMK-007 4.6 lb (2.1 Kg) 55.1 lb (25 Kg) 500mm-780mm(from mounting plate center to the screen) ± 5° tilt, left\right, front\rear and lateral rotation adjustment Important Safety 1. Please read this manual carefully and follow all safety rules before installa�on. 2. For safety reasons, please make sure the wall is strong enough to sustain the weight of the projector & wall mount. 3. The total maximum weight of all items mounted should NEVER exceed the weight capacity: 55 lbs (25kg). 4. DO NOT a�empt to alter or modify any part of the wall mount or its a�achments. 5. Do not install the projector wall mount on a structure that is prone to vibra�on, movement or chance of impact. 6. To avoid risk of fire, do not install the projector with the projector wall mount in a humid or excessively dusty place. 7. Use the supplied accessories only. Use of accessories other than those supplied may result in damage to the projector and/or projector wall mount. 8. Unplug the AC power cord and any other connected cables before dismounting the projector from the projector wall mount. 9. Do not hit or hang any heavy objects on the projector wall mount. If the projector wall mount is damaged, stop using immediately and contact a qualified service personnel immediately. 10. Only install the projector wall mount horizontally on the level surfaces. * The manufacturer is not liable for any damages or injury caused by mishandling or improper installa�on. 11. The projector or wall mount may fall and cause personal injury. Ensure screws are tightened to the proper torque after installation and any adjustments. Do not overtighten screws as this may cause screw deformation. 12. This wall mount kit ONLY supports ViewSonic® projectors and models that are designated by ViewSonic. Use with non-ViewSonic branded projectors or exceeding the weight capacity is neither supported nor recommended, may cause property damage or personal injury, and shall be at the sole risk of users/installers. PJ-WMK-007 Quick Start Guide 中国 http://www.viewsonic.com.cn 电话：4008 988 188 香港 http://www.hk.viewsonic.com 電話：852 3102 2900 澳門 http://www.hk.viewsonic.com 電話：853 2840 3687 台灣 http://www.viewsonic.com.tw 電話：0800 899 880 한국 http://ap.viewsonic.com/kr/ Phone: 080 333 2131 Singapore/Malaysia/Thailand http://www.viewsonic.com.sg Phone: 65 6461 6044 India http://www.in.viewsonic.com Phone: 1800-419-0959 United States http://www.viewsonic.com Phone: 1-800-688-6688 Canada http://www.viewsonic.com Phone: 1-866-463-4775 Europe http://www.viewsoniceurope.com http://www.viewsoniceurope.com/uk/support/call-desk/ Australia/New Zealand http://www.viewsonic.com.au Phone: 1800 880 818 (AUS) 0800 008 822 (NZ) South Africa http://ap.viewsonic.com/za/ Latin America (Chile) http://www.viewsonic.com/la/ http://www.viewsonic.com/la/soporte/servicio-tecnico Latin America (Mexico) http://www.viewsonic.com/la/ http://www.viewsonic.com/la/soporte/servicio-tecnico Latin America (Peru) http://www.viewsonic.com/la/ http://www.viewsonic.com/la/soporte/servicio-tecnico Latin America (Argentina) http://www.viewsonic.com/la/ http://www.viewsonic.com/la/soporte/servicio-tecnico Puerto Rico & Virgin Islands http://www.viewsonic.com Phone: 1-800-688-6688 (English) http://www.viewsonic.com/la/soporte/servicio-tecnico PJ-WMK-007_QSG_Rev. 1b 01-06-21 Copyright © 2021 ViewSonic Corporation. All rights reserved.