ViewSonic VSB050 User Guide English - Page 16

Regulatory and Service Information, Please read before proceeding, Compliance Information, FCC

Get ViewSonic VSB050 PDF manuals and user guides View all ViewSonic VSB050 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Regulatory and Service Information Please read before proceeding • Do not store your device in temperatures higher than 50°C (122°F). • The operating temperature for this device is from 0°C (32°F) to 35°C (95°F). Compliance Information This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit. FCC Compliance Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The antenna(s) used for this transmitter must not be collocated or operating in conjunction with any other antenna or transmitter. The device was tested and complies to measurement standards and procedures specified in FCC CFR Tile 47 Part 15 Subpart C 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
16
Regulatory and Service Informa°on
Please read before proceeding
• Do not store your device in temperatures higher than 50°C (122°F).
•
The opera°ng temperature for this device is from 0³C (32³F) to 35³C (95³F).
Compliance Informa°on
This sec°on addresses all connected requirements and statements regarding
regula°ons. Confirmed corresponding applica°ons shall refer to nameplate labels
and relevant markings on the unit.
FCC Compliance Statement
This device complies with part 15 of FCC Rules. Opera°on is subject to the following
two condi°ons: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired opera°on. This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protec°on against harmful
interference in a residen°al installa°on. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used in accordance
with the instruc°ons, may cause harmful interference to radio communica°ons.
However, there is no guarantee that interference will not occur in a par°cular
installa°on. If this equipment does cause harmful interference to radio or television
recep°on, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
•
Increase the separa°on between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifica°ons not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The antenna(s) used for this transmi±er must not be collocated or opera°ng in
conjunc°on with any other antenna or transmi±er.
The device was tested and complies to measurement standards and procedures
specified in FCC CFR Tile 47 Part 15 Subpart C