Viking VCWH 1200 CFM In-Line Ventilator Kit - Installation Instructions
Viking VCWH Manual
 |
View all Viking VCWH manuals
Add to My Manuals
Save this manual to your list of manuals |
Viking VCWH manual content summary:
- Viking VCWH | 1200 CFM In-Line Ventilator Kit - Installation Instructions - Page 1
VIKING MODEL DIL1200 INLINE FAN ONLY FOR USE WITH: VCWH, VCIH, DBCV, DICV, DCWH, DCIH, DCWL, DCWN, DTWS, DSWB 30"W to 66"W WALL AND ISLAND HOODS READ AND SAVE THESE INSTRUCTIONS . 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to - Viking VCWH | 1200 CFM In-Line Ventilator Kit - Installation Instructions - Page 2
rigid metal ductwork. 4. Always install ventilation products with an approved wall or roof cap. 5. For a truly quiet kitchen ventilation system add a Viking Inline Duct Silencer part number VSIL10 (sold separately) to the installation. The simple addition of a inline duct silencer between the range - Viking VCWH | 1200 CFM In-Line Ventilator Kit - Installation Instructions - Page 3
TO THE RANGE HOOD ROUGH IN BOX 1. The opposite end of this wiring will be connected to the 1. Run 115VAC electrical power cable from the service panel range hood rough in box in the next step. and from the inline fan to the range hood rough in box. 2. Remove wiring box - Viking VCWH | 1200 CFM In-Line Ventilator Kit - Installation Instructions - Page 4
support the weight of the inline fan. The inline fan should be supported with the integral brackets of the inline fans. If special supports power supply and lock out service panel before cleaning or servicing this unit. CLEANING Periodic inspection VIKING RANGE CORPORATION GREENWOOD, MISSISSIPPI 38930 USA Item
-
1 -
2 -
3 -
4
 |
 |
VIKING MODEL DIL1200
INLINE FAN
ONLY FOR USE WITH: VCWH, VCIH, DBCV, DICV, DCWH, DCIH, DCWL,
DCWN, DTWS, DSWB 30"W to 66"W WALL AND ISLAND HOODS
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
1.
Use this unit only in the manner intended by the manufac-
turer.
If you have questions, contact the manufacturer or
your distributor.
2.
Before servicing or cleaning unit, switch power off at ser-
vice panel and lock the service disconnecting means to pre-
vent power from being switched on accidentally.
When the
service disconnecting
means cannot be locked, securely
fasten a prominent warning device, such as a tag, to the
service panel.
3.
Installation work and electrical wiring must be done by
a qualified person(s) in accordance with all applicable
codes and standards, including fire rated construction
codes and standards.
4. Sufficient air is needed for proper combustion and ex-
hausting of gases through the flue (chimney) of fuel
burning equipment to prevent backdrafting. Follow the
heating equipment manufacturer’s
guidelines and safety
standards such as those published by the National Fire
Protection Association (NFPA), and the American Society
for Heating, Refrigeration and Air Conditioning Engineers
(ASHRAE), and the local code authorities.
5
When cutting or drilling into wall, or ceiling, do not
damage electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. To reduce risk of fire, use only metal ductwork.
8.
This unit must be grounded.
CAUTION
1.
For general ventilating use only.
Do not use to exhaust
hazardous or explosive material and vapors.
2.
To avoid motor bearing damage and noisy and/or
unbalanced impellers, keep drywall spray, construction
dust, etc. off power unit.
3.
Please read specification label on product for additional
information and requirements.
4.
Unit has an unguarded impeller.
Do not use in locations
where the impeller is readily accessible to people or ani-
mals.
5.
Screen guards must be installed if impeller is within reach
of personnel,
and less than 7 feet above the floor.
6.
When handling fan wear hand protection and stay
clear of sharp edges.
7.
Because this unit has rotating parts, safety
should be
exercised during all phases of installation, operation and
maintenance.
8.
The motor is permanently lubricated.
Do not oil or disas-
semble motor.
9.
Electrical circuit, including speed control, (if used), must
be rated 5.0 AMPS minimum.
SPECIFICATIONS
MODEL
VOLTS
AMPS
CFM
DUCT SIZE
DIL1200
115
4.84
1200
10” DIA.
INSTALLER: Leave this Manual With The Homeowner
HOMEOWNER: Use And Care Information On Page 4
1