Vtech 80-6113-00 User Guide

Vtech 80-6113-00 - AT&T E5812B - 5.8 GHz Dual Handset Answering System Manual

Get Vtech 80-6113-00 - AT&T E5812B - 5.8 GHz Dual Handset Answering System PDF manuals and user guides
UPC - 650530015618
View all Vtech 80-6113-00 manuals
Add to My Manuals
Save this manual to your list of manuals

Vtech 80-6113-00 manual content summary:

  • Vtech 80-6113-00 | User Guide - Page 1
    product. Before using this telephone, please read the Important safety instructions on page 29 of this manual. This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech telephone. Please review this manual thoroughly to ensure proper installation
  • Vtech 80-6113-00 | User Guide - Page 2
    from redial 24 Delete from redial 24 Handset and telephone base indicators 25 Telephone base lights 25 Handset icons 25 Handset display screen messages 26 Call log display screen messages 27 Battery 28 Important safety instructions 29 Troubleshooting 30 Operating range 38 Maintenance 38
  • Vtech 80-6113-00 | User Guide - Page 3
    Table of contents About cordless telephones 39 Warranty 39 FCC, ACTA and IC regulations 41 The RBRC® seal 42 Technical specifications 43 Index 44 www.vtechphones.com iii
  • Vtech 80-6113-00 | User Guide - Page 4
    case it is necessary to ship your telephone for warranty service. Check to make sure the telephone package includes the following: 1. Telephone base 2. Handset 3. Base power adapter 4. Battery 5. Telephone line cord 6. User's manual • For replacement batteries or power adapter, visit our website at
  • Vtech 80-6113-00 | User Guide - Page 5
    it upwards until it clicks into place. • Put the handset in the telephone base to charge the new battery for at least 16 hours. You can keep the battery charged by returning the handset to the telephone base after each use. When the battery power is fully depleted, a full recharge takes about 16
  • Vtech 80-6113-00 | User Guide - Page 6
    an electrical outlet not controlled by a wall switch. 3. Route cords through the slots on the telephone base • Use only the VTech batteries and power adapter (or equivalent) supplied with this telephone. To obtain a replacement, visit our website at www.vtechphones. com or call 1 (800) 595-9511
  • Vtech 80-6113-00 | User Guide - Page 7
    ID features are not functioning properly, install a DSL filter on the telephone line between the telephone base and the telephone wall jack. Contact your DSL provider for a DSL filter. Telephone Noise filter (For line cord DSL users) To single telephone jack (RJ11C)  www.vtechphones.com
  • Vtech 80-6113-00 | User Guide - Page 8
    Installation Basic operation Telephone settings Handset layout 1. Earpiece 2. CID/ (caller ID/volume) 3. /FLASH 1 4. Dialing keys (0-9,*,#) 5. REDIAL/PAUSE 6. Microphone 7. Handset display 7 8. MENU/SELECT 8 9. / (directory/volume) 10. OFF/CLEAR 2 9 11. REMOVE 3 10 12. MUTE 4
  • Vtech 80-6113-00 | User Guide - Page 9
    Telephone settings Telephone base layout 1. FIND HANDSET 2. CHARGE light 3. IN USE light 4. VOICEMAIL light 1 2 3 4  www.vtechphones.com
  • Vtech 80-6113-00 | User Guide - Page 10
    settingsBasic operation Telephone settings Date and time • Press MENU/SELECT to display menu when in idle mode. • Press or to reach Date/Time. Press MENU/SELECT. • Use the
  • Vtech 80-6113-00 | User Guide - Page 11
    telephone is ringing, you can temporarily silence the ringer by pressing OFF/CLEAR or MUTE. A ringer off icon will be displayed. The next call will ring normally. Ring volume The handset ll hear a confirmation beep. Battery low tone The handset is preset to beep when the battery level is low. •
  • Vtech 80-6113-00 | User Guide - Page 12
    settings Out of range tone The handset will beep during a conversation when it is out of range from the telephone base. This tone is preset to /SELECT. • The screen displays Stored and you'll hear a confirmation beep. Tones Handset name Out of Range KEY BEEPS On Off • Press OFF/CLEAR at anytime to
  • Vtech 80-6113-00 | User Guide - Page 13
    to 14 characters only. • Only handset display screens are affected by the language setting. Telephone settings Edit handset name • Press MENU/SELECT to display the menu when in idle mode. • Press or to reach Setup HS. Press MENU/SELECT. • Press or to reach Handset Name. Press MENU/SELECT. • Press
  • Vtech 80-6113-00 | User Guide - Page 14
    . Dial TYPE Clr VoiceMail TONE Pulse Clear voicemail If you subscribe to voicemail services provided by your local telephone company, NEW VOICEMAIL will appear on the handset display and the VOICEMAIL light on the telephone base will flash when you have a new voicemail message. This feature allows
  • Vtech 80-6113-00 | User Guide - Page 15
    settings • When the default settings are reset, all the previously stored settings cannot be retrieved. Reset to default settings The handset and the telephone base can be individually reset to their default settings by selecting RESET in the SETUP HS or SETUP BS menus respectively. • Press
  • Vtech 80-6113-00 | User Guide - Page 16
    call comes in, you will hear a beep. The caller ID information will be displayed if you subscribe to caller ID service from your local telephone company. • Press /FLASH on the handset to answer the incoming call and put the current call on hold. • Press /FLASH at anytime to alternate between calls
  • Vtech 80-6113-00 | User Guide - Page 17
    send touch tone signals. 3. Dial the number. 4. After hanging up, the telephone will automatically return to pulse dial service. Find handset • Press FIND HANDSET on the telephone base to locate the handset when in idle mode. The handset will ring and Paging will flash on its screen. • Press FIND
  • Vtech 80-6113-00 | User Guide - Page 18
    • Press MENU/SELECT to display menu when in idle mode. VTECH 1-595-9511 • Press or to reach directory. Press MENU/SELECT. • Press or to reach REVIEW. Press MENU/SELECT. • Enter a name using the dial pad (see Character chart on page 16). The first name beginning with that letter will be displayed
  • Vtech 80-6113-00 | User Guide - Page 19
    a single character. • Press and hold REMOVE to delete the entire entry. • Press and hold REDIAL/PAUSE to insert a dialing pause (P will be displayed) when entering a telephone number. www.vtechphones.com
  • Vtech 80-6113-00 | User Guide - Page 20
    to dial. -OR• Press MENU/SELECT to display menu when in idle mode. • Press or to reach directory. Press MENU/SELECT. • Press or to reach REVIEW. Press MENU/SELECT. • Press or to scroll to the desired entry, or use the alphabetical search to find it. • Press /FLASH to dial. STORE
  • Vtech 80-6113-00 | User Guide - Page 21
    Advanced operation • Press OFF/CLEAR to return to the previous screen. Press and hold OFF/CLEAR to exit the menu at anytime. Edit an entry in the directory • Press / or MENU/SELECT three times to enter the directory. • Press or t�o��s�c��ro��ll��to��t�h�e���d�e�s�i�r�e�d��e�n��tr�y��o��r�u�s��e��
  • Vtech 80-6113-00 | User Guide - Page 22
    Advanced operation About caller ID If you subscribe to caller ID service from your local telephone company, this feature displays the name and telephone number of the caller before answering a call (even when you are on another call). The caller ID features of this product will work only if you
  • Vtech 80-6113-00 | User Guide - Page 23
    the caller will be displayed if you subscribe to caller ID service from your local telephone company. • The call log can store up to 50 entries The screen displays New if there are new call log entries (missed and unread calls). Review the call log • Press CID/ to enter the call log. -OR- • Press
  • Vtech 80-6113-00 | User Guide - Page 24
    MENU/SELECT. •��T�h�e��s�c�r�e�e��n�d��is�p��la�y�s� Stored and you'll hear a confirmation beep. enter name a stored • While reviewing the call log, press # repeatedly to display the other dialing options. The available options are: (1 + area
  • Vtech 80-6113-00 | User Guide - Page 25
    • Press OFF/CLEAR to return to the previous screen. Press and hold OFF/CLEAR to exit the menu at anytime. Advanced operation Delete from the call log • Press CID/ to enter the call log. -OR- • Press MENU/SELECT. Press or to select Call log, then press MENU/SELECT. To delete one entry • Press or to
  • Vtech 80-6113-00 | User Guide - Page 26
    entry will be deleted to make room as you place additional calls. • The screen displays Empty if there are no records in the list. Review redial • Press REDIAL/PAUSE to enter the redial list. • Press or to browse through the entries. Store a redial number to the directory •��P�r�e�s�s� REDIAL/PAUSE
  • Vtech 80-6113-00 | User Guide - Page 27
    Advanced operation • Press OFF/CLEAR to return to the previous screen. Press and hold OFF/CLEAR to exit the menu at anytime. Dial from redial • Press REDIAL/PAUSE to enter the redial list. • Press or to scroll to the desired entry. • �P�r�e�s�s� /FLASH to dial. Delete from redial • Press REDIAL/
  • Vtech 80-6113-00 | User Guide - Page 28
    there is a new network message (A subscription service from your local telephone company is required). CHARGE • On when the handset is in the telephone base. Handset icons • Ringer off. (Battery indicator) • Cycles (low, medium, and full) when handset battery is charging. • Flashes when the
  • Vtech 80-6113-00 | User Guide - Page 29
    . A handset with low battery has been placed on the telephone base to recharge. The cordless handset is searching for the telephone base. handset connected to the same line is in use. The battery needs to be recharged. The microphone is muted temporarily during a conversation. There are un-reviewed
  • Vtech 80-6113-00 | User Guide - Page 30
    display screen messages Display: PAGING PHONE WARNING CHECK BATTERY! When: The handset locator has been activated or the handset is being paged. The handset is in use. The battery is not installed or not installed properly in the handset. -OR The battery needs to be replaced. -OR An incorrect
  • Vtech 80-6113-00 | User Guide - Page 31
    not in use (standby*) 100 hours *Handset is off the telephone base but not in use. The battery needs charging when: • A new battery is installed in the handset. • Battery indicator on screen is flashing. • The telephone beeps when taken off the telephone base. CAUTION: 1. Use only the supplied
  • Vtech 80-6113-00 | User Guide - Page 32
    but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions, as improper adjustment of other
  • Vtech 80-6113-00 | User Guide - Page 33
    Service, visit our website at www. vtechphones.com, or call 1 (800) 595-9511; in Canada, call 1 (800) 267-7377. Problem Suggestion My telephone does not work at all. • Make sure the battery is installed and charged correctly (page 2). For optimum daily performance, return the cordless handset
  • Vtech 80-6113-00 | User Guide - Page 34
    see the Battery section of this user's manual (page 28). • The telephone might be malfunctioning. Please see the Warranty section of this user's manual (page 39) for further instruction. The CHARGE light is off. • Clean the charging contacts on the cordless handset(s) and telephone base each
  • Vtech 80-6113-00 | User Guide - Page 35
    Troubleshooting Problem Suggestion There is no dial tone. no dial tone on the other telephone either, the problem is in your wiring or local service. Contact your local telephone company. My handset displays • Move the handset closer to the telephone base. You might have moved out
  • Vtech 80-6113-00 | User Guide - Page 36
    Troubleshooting Problem The telephone does not ring when there or local service. Contact the local telephone company cordless telephones. •� Test a working telephone at the telephone jack. If another telephone has the same problem, the problem is in the telephone jack. Contact your local telephone
  • Vtech 80-6113-00 | User Guide - Page 37
    Troubleshooting Problem I cannot dial out. Suggestion • First, try all the above suggestions. • Make sure there is a dial tone before dialing. It is normal if the cordless handset takes a second or two to synchronize with the telephone base before producing a dial tone. Wait an extra second before
  • Vtech 80-6113-00 | User Guide - Page 38
    Troubleshooting Problem There is noise or interference during a telephone conversation. My calls cut in and out when I am using the cordless handset. Suggestion are still not clear, the problem is probably in the wiring or local service. Contact the local telephone company (charges may apply).
  • Vtech 80-6113-00 | User Guide - Page 39
    in��a��d�i�f�fe�r�e��n�t�t�e�le��p�h�o��n�e�.�I�f�t�h�e��re��a�r�e� using the telephone. still other calls, the problem is probably in the wiring or local service. Call your local telephone company. I hear noise in the cordless handset, and none of the keys or
  • Vtech 80-6113-00 | User Guide - Page 40
    Troubleshooting Problem My cordless handset beeps and is not performing normally. computers, kitchen appliances and other cordless telephones. Common cure for electronic equipment • If the unit is not responding normally, try putting the cordless handset in the telephone base. If it does not
  • Vtech 80-6113-00 | User Guide - Page 41
    , then press /FLASH to answer the call. If the handset moves out of range during a telephone conversation, there might be interference. To improve reception, move closer to the telephone base. Maintenance Taking care of your telephone Your cordless telephone contains sophisticated electronic parts
  • Vtech 80-6113-00 | User Guide - Page 42
    cordless handset. For this reason, you should not think of cordless telephone conversations as being as private as those on corded telephones. • Electrical Power: The telephone base of this cordless telephone instructions. service representative of VTech; or 3. Product to the extent that the problem
  • Vtech 80-6113-00 | User Guide - Page 43
    , please call 1 (800) 595-9511; in Canada, please call 1 (800) 267-7377. NOTE: Before calling for service, please review the user's manual - a check of the Product controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during
  • Vtech 80-6113-00 | User Guide - Page 44
    The handset may be safely held against the ear of the user. The telephone base shall be installed and used such that parts of the user's Installation Instructions in the user's manual. The Ringer Equivalence Number (REN) is used to determine how many devices you may connect to your telephone line
  • Vtech 80-6113-00 | User Guide - Page 45
    cordless handset, it is hearing aid compatible. If this product has memory dialing locations, you may choose to store emergency telephone signifies that the Industry Canada technical specifications were met. The Ringer Equivalence batteries at the end of their useful lives, when taken out of service
  • Vtech 80-6113-00 | User Guide - Page 46
    to environmental conditions at the time of use. Handset: 160.0mm X 50.0mm X 31.0mm Telephone base: 117.0mm X 107.5mm X 87.0mm Handset: 113.2 grams (including battery) Telephone base: 156.0 grams Handset: 2.4V DC 600mAh NiMH battery Telephone base: 6V DC @ 300mAh Directory: 50 memory locations
  • Vtech 80-6113-00 | User Guide - Page 47
    FCC, ACTA and IC regulations 41 Find handset 14 H Handset and telephone base indicators 25 Handset display screen messages 26 Handset icons 25 Handset layout 5 I Important safety instructions 29 Index 44 Installation 1 Install handset battery 2 K Key tone 9 L Language 10 www.vtechphones
  • Vtech 80-6113-00 | User Guide - Page 48
    entry 17 Store a redial number to the directory 23 Store a call log number 21 T Technical specifications 43 Telephone base 3, 6 Telephone base lights 25 Telephone settings 5 Temporary tone dialing 14 The RBRC® seal 42 Troubleshooting 30 V Volume 8 W Warranty 39 www.vtechphones.com 45
  • Vtech 80-6113-00 | User Guide - Page 49
    VTECH TELECOMMUNICATIONS LTD. A member of THE VTECH GROUP OF COMPANIES. Distributed in the U.S.A. by VTech Communications, Inc. Beaverton, Oregon Distributed in Canada by VTech Telecommunications Canada, Ltd., Richmond, B.C. Copyright ©2007 for VTECH TELECOMMUNICATIONS LTD. Printed in China. 91-
  • Vtech 80-6113-00 | User Guide - Page 50
    User's manual www.vtechphones.com Model : LS6113-WT/ LS6113-BK
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
www.vtechphones.com
±
Th±s manual has all the feature operat±ons and troubleshoot±ng necessary to ±nstall
and operate your new VTech telephone. Please rev±ew th±s manual thoroughly to
ensure proper ±nstallat±on and operat±on of th±s ±nnovat±ve and feature r±ch VTech
product. For support, shopp±ng, and everyth±ng new at VTech, v±s±t our webs±te at
www.vtechphones.com.
In Canada, go to www.vtechcanada.com.
Congratulations
on purchas±ng your new VTech product.
Before us±ng th±s telephone, please read the
Important safety instructions
on page 29 of th±s manual.
The ENERGY STAR
R
program (www.energystar.gov) recogn±zes and encourages
the use of products that save energy and help protect our env±ronment. We are
proud to mark th±s product w±th the ENERGY STAR
R
label ±nd±cat±ng ±t meets
the latest energy eff±c±ency gu±del±nes.