Weider 265 English Manual
Weider 265 Manual
 |
View all Weider 265 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider 265 manual content summary:
- Weider 265 | English Manual - Page 1
Model No. WESY19611 Serial No. Write the serial number in the space above for reference. USER'S MANUAL Serial Number Decal QUESTIONS? If you have questions, or if there are missing or damaged parts precautions and instructions in this manual before using this equipment. Save this manual for future - Weider 265 | English Manual - Page 2
ASSEMBLY 5 ADJUSTMENTS 19 TROUBLE-SHOOTING AND MAINTENANCE 21 WEIGHT RESISTANCE CHART 22 CABLE DIAGRAM 23 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: An EXPLODED DRAWING/PART LIST and a PART IDENTIFICATION CHART are attached in the center of this manual. Remove the - Weider 265 | English Manual - Page 3
the weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. Use the weight system only as described in this manual. 13. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop - Weider 265 | English Manual - Page 4
. The model number is WESY19611. The serial number can be found on a decal attached to the weight system (see the front cover of this manual). For your benefit, read this manual carefully before using the weight system. If you have additional questions, please call our Customer Service Department - Weider 265 | English Manual - Page 5
the weight system, make sure that all parts are oriented exactly as shown in the drawings. Tightening Parts Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after reading the assembly instructions, please call our Customer Service Department - Weider 265 | English Manual - Page 6
. Attach the Top Frame (55) to the Front Upright (42) and the Rear Upright (56) with four 5/16" x 2 3/4" Bolts (11), the Long Support Plate (91), the Short Support Plate (103), and four 5/16" Nylon Locknuts (3) as shown. Tighten all of the 5/16" Nylon Locknuts (3) used in steps 1 to 3. 6 4 1 11 - Weider 265 | English Manual - Page 7
outer holes in each of the Weights (25). Slide the Weights onto the Weight Guides (62). Make sure that the Weights are turned so the pin grooves are on the indicated side. 6. Place a piece of cardboard under each Weight Guide (62) to protect the floor for this step. 6 Lift the upper ends of the - Weider 265 | English Manual - Page 8
(50) to the Right Arm (48) with a 3/8" x 2 1/2" Bolt (7) and a 3/8" Nylon Locknut (21). Do not tighten the Nylon Locknut yet. Attach a "V"-Pulley (6) and a Long Cable Trap (50) to the Left Arm (47) in the same way. 3 17 7 50 50 6 6 21 47 21 Welded Brackets 48 10. Lubricate both axles on - Weider 265 | English Manual - Page 9
11. Press a 1 3/4" Square Inner Cap (44) into the Seat Frame (36). Attach a Bumper (73) to the Seat Frame with a #8 x 3/4" Tap Screw (65). Slide the Seat Frame (36) onto the 5/16" x 2 1/2" Carriage Bolts (1) in the Base (4). See the inset drawing. The indicated bracket on the Seat Frame must be - Weider 265 | English Manual - Page 10
ASSEMBLY 14. During steps 15 through 44, refer to the CABLE DIAGRAMS on page 23 of this manual to verify proper cable routing. Before beginning this section, identify the High Cable (23), the Low Cable (19), the Press Cable (58), and the Resistance Cable (27) by comparing the ends and lengths of the - Weider 265 | English Manual - Page 11
(21). Make sure that the Cable Trap is turned to hold the Cable in place. 20 12 23 15 21 66 56 21. Route the High Cable (23) over a 3 1/2" Pulley 21 (15). Attach the Pulley inside of the bracket on the Top Frame (55) that is between the Weight Guides (62) with a 3/8" x 2" Bolt (12) and - Weider 265 | English Manual - Page 12
Make sure that the Plastic Stabilizer is wrapped around the Weight Tube. Insert the Weight Tube (63) into the center holes in the stack of Weights (25). 23 67 3 63 25 72 23. Identify the Low Cable (19). Wrap the Low Cable under the 3 1/2" Pro Pulley (77). Attach the Pulley to the Rocker Arm (32 - Weider 265 | English Manual - Page 13
as shown in the inset drawing. Do not overtighten the Nylon Locknut; the Cable must be able to pivot freely. 28 58 77 66 Route the Press Cable (58) under a 3 1/2" Pro Pulley (77). Attach the Pulley and a Cable Trap (66) to the Seat Frame (36) with a 3/8" x 3 1/2" Bolt (16), a 3/8" Washer (9), and - Weider 265 | English Manual - Page 14
Washer (9), and a 3/8" Nylon Jamnut (33). Make sure that the Cable Trap is turned to hold the Cable in place. 6 21 58 50 7 36 32 33 66 15 9 16 58 31. Route the Press Cable (58) through the Press 31 Frame (17) and wrap the Cable around a 3 1/2" Pulley (15). Attach the Pulley inside of the - Weider 265 | English Manual - Page 15
Cable Trap is turned to hold the Cable 56 15 in place. Properly tighten the 3/8" Nylon Locknut (21). 58 66 21 34. Attach the end of the Press Cable (58) the Resistance Bracket (35) and release the knob so that the pin on the knob is inserted into the upper adjustment hole in the Resistance - Weider 265 | English Manual - Page 16
(101) onto the bolt at the end of the Resistance Cable (27). Thread the Resistance Cable part way into the lower end of the Weight Tube (63). Tighten the Plane Nut against the 63 Weight Tube. 101 27 38. Wrap the Resistance Cable (27) around a 3 1/2" 38 Pulley (15). Attach the Pulley inside - Weider 265 | English Manual - Page 17
) onto 44 the indicated 3/8" x 3" Grade 5 Bolt (98), on the outside of the wide bracket on the Base (4). Note: Be sure the Resistance Cable is on the inside of the Press Cable (58). Tighten a 3/8" Nylon Jamnut (33) onto the 3/8" x 3" Grade 5 Bolt (98). Do not overtighten the Nylon Jamnut; the - Weider 265 | English Manual - Page 18
(8), and a 5/16" Nylon Locknut (3). Align one set of holes in the Press Adjustment Tube (79) with the holes in the Rocker Arm (32). Insert the "L"-Pin (40) into the holes. Make sure that the Press Adjustment Tube is oriented as shown. Apply the "320 LB. LEG PRESS" decal to the center - Weider 265 | English Manual - Page 19
to remove the slack by tightening the cables. See TROUBLE-SHOOTING AND MAINTENANCE on page 21. ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each - Weider 265 | English Manual - Page 20
Cable (23) with a Cable Clip (53). For some exercises, the Chain (52) should be attached between the Lat Bar and the High Cable with two Cable . Re-insert the "L"-Pin. For some exercises, the Press Adjustment Tube (79) must be removed. Remove the "L"-Pin (40), and lift the Press Adjustment Tube - Weider 265 | English Manual - Page 21
TROUBLE-SHOOTING AND MAINTENANCE Make sure that all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES 1 Woven cable, - Weider 265 | English Manual - Page 22
the approximate weight resistance, in pounds, at each exercise station. For example, if the resistance handle is set at position 2 (see the drawing below), if the weight pin is inserted under 3 weights, and if the leg lever is being used, the chart shows that the approximate weight resistance will - Weider 265 | English Manual - Page 23
proper routing of the Low Cable (19), the High Cable (23), the Resistance Cable (27), and the Press Cable (58). Use the diagram to make sure that the cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not function properly - Weider 265 | English Manual - Page 24
3/4" Round Inner Cap (34) 1" x 7/8" Plastic Bushing (75) 1" Round Inner Cap (49) 1/2" x 7/8" Spacer (100) 5/8" x 7/8" Spacer (61) 1/2" x 1/2" Spacer (96) 1 3/4" Square Inner Cap (44) Cable Clip (53) 1" Retainer (69) 1" Round Cover Cap (70) 2" Square Inner Cap (76) 2" Square Outer Cap (51) - Weider 265 | English Manual - Page 25
PART IDENTIFICATION CHART-WESY19611 R0102A 1/4" Washer (10) 5/16" x 1 3/4" Bolt (72) 5/16" Washer (8) 3/8" x 2" Bolt (12) 3/8" Washer (9) 1/4" Nylon Locknut (2) 5/16" Nylon Jamnut (99) 5/16" Nylon Locknut (3) 3/8" Nylon Jam Nut (33) 3/8" Nylon - Weider 265 | English Manual - Page 26
5/16" x 2 3/4" Bolt (11) 5/16" x 2 3/4" Carriage Bolt (94) 3/8" x 3" Bolt (93) 3/8" x 3" Grade 5 Bolt (98) 3/8" x 3 1/4" Bolt (68) 3/8" x 3 1/2" Bolt (16) 3/8" x 3 1/2" Bolt (16) 3/8" x 3 3/4" Bolt (71) 5/16" x 6" Bolt (60) 3/8" x 6" Bolt (64) 1/4" x 3/4" Screw (18) #8 x 3/4" Tap Screw (65) 5/16" x - Weider 265 | English Manual - Page 27
PART LIST-Model No. WESY19611 R0102A Weight Bumper 96 1 Bushing 1/2" x 1/2" 97 1 Metal Cable Trap 98 1 3/8" x 3" Grade 5 Bolt 99 2 5/16" Nylon Jamnut 100 2 1/2" x 7/8" Spacer 101 1 1/2" Plane Nut 102 4 Special Washer 103 1 Small Support Plate # 1 User's Manual # 1 Exercise Guide - Weider 265 | English Manual - Page 28
21 15 12 51 66 15 3 66 15 98 3 49 60 46 12 15 21 3 2 12 10 57 58 16 27 1 33 51 4 1 5 15 66 20 76 20 21 94 51 12 97 84 23 3 43 33 3 8 3 78 40 32 9 16 9 21 44 7 33 66 73 65 15 33 58 96 77 93 16 19 30 34 68 29 34 21 30 9 80 44 21 R0102A EXPLODED DRAWING - Weider 265 | English Manual - Page 29
give the following information: • The MODEL NUMBER of the product (WESY19611) • The NAME of the product (WEIDER® 265 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART LIST and EXPLODED DRAWING at the
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
 |
 |
USER’S MANUAL
Model No. WESY19611
Serial No.
Write the serial number in the
space above for reference.
Patent Pending
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Serial Number Decal
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST