Weider 400 English Manual - Page 6

Press four 25.4mm Square Inner Caps 19 into - weight

Get Weider 400 PDF manuals and user guides View all Weider 400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3. Attach the Crossbars (2, 3) to the Uprights (1) with four M8 x 65mm Bolts (20), two Support 3 Plates (10), and four M8 Nylon Locknuts (24). Do not tighten the Locknuts yet. Note the position of the name decal and make sure the Uprights are oriented as shown. 24 10 1 1 20 Name Decal 3 20 2 20 10 24 24 4. Press a 25.4mm Round Inner Cap (15) into the indicated end of the Weight Tube (31). Slide the Weight Tube through the hole in the Leg Lever (6). Attach the Weight Tube with an M8 x 50mm Bolt (29), two M8 Washers (26), a Sleeve (30), and an M8 Nylon Locknut (24). Press a 25.4mm Angle Cap (16) onto the other end of the weight tube. Tap three 38mm Square Inner Caps (17) into the Leg Lever (6) as shown. Lubricate the M10 x 60mm Bolt (21). Attach the Leg Lever (6) to the Front Leg (5) with the Bolt and an M10 Nylon Locknut (27). Do not overtighten the Locknut; the Leg Lever must be able to pivot freely. 5. Press four 25.4mm Square Inner Caps (19) into the Backrest Tubes (7). Attach the Backrest Tubes (7) to the Backrest (8) in the indicated locations, with three M6 x 38mm Screws (23) and three M6 Washers (25). Do not tighten the Screws yet. 4 17 27 17 6 24 26 5 21 16 15 5 31 30 17 26 29 8 19 19 25 25 7 23 23 25 7 23 19 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
6
3.
Attach the Crossbars (2, 3) to the Uprights (1)
with four M8 x 65mm Bolts (20), two Support
Plates (10), and four M8 Nylon Locknuts (24).
Do
not tighten the Locknuts yet. Note the position
of the name decal and make sure the Uprights
are oriented as shown.
4.
Press a 25.4mm Round Inner Cap (15) into the
indicated end of the Weight Tube (31). Slide the
Weight Tube through the hole in the Leg Lever (6).
Attach the Weight Tube with an M8 x 50mm Bolt
(29), two M8 Washers (26), a Sleeve (30), and an
M8 Nylon Locknut (24). Press a 25.4mm Angle
Cap (16) onto the other end of the weight tube.
Tap three 38mm Square Inner Caps (17) into the
Leg Lever (6) as shown.
Lubricate the M10 x 60mm Bolt (21). Attach the
Leg Lever (6) to the Front Leg (5) with the Bolt and
an M10 Nylon Locknut (27).
Do not overtighten
the Locknut; the Leg Lever must be able to
pivot freely.
4
27
17
17
17
6
5
15
31
16
21
24
26
26
30
29
3
10
10
20
20
20
24
24
24
3
2
1
1
Name
Decal
5.
Press four 25.4mm Square Inner Caps (19) into
the Backrest Tubes (7).
Attach the Backrest Tubes (7) to the Backrest (8)
in the indicated locations, with three M6 x 38mm
Screws (23) and three M6 Washers (25).
Do not
tighten the Screws yet.
8
25
25
25
23
23
7
7
23
19
19
19
5