Weider Pro 3770 English Manual
Weider Pro 3770 Manual
 |
View all Weider Pro 3770 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Pro 3770 manual content summary:
- Weider Pro 3770 | English Manual - Page 1
satisfaction. If you have questions, or if there are missing parts, we will guarantee complete satisfaction through assistance from our factory Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at - Weider Pro 3770 | English Manual - Page 2
YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENTS 21 WEIGHT RESISTANCE CHART 23 TROUBLESHOOTING 24 CABLE DIAGRAMS 25 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of this manual. Remove the - Weider Pro 3770 | English Manual - Page 3
will fall with great force. 10. The weight system is designed to support a a maximum user weight of 300 pounds. 11. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on all of the pulleys. 12 - Weider Pro 3770 | English Manual - Page 4
to the weight system (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. High Pulley Station Lat Bar WARNING DECAL Ab Pulley Station Press Arms Seat Leg Press Weight Stack ASSEMBLED DIMENSIONS - Weider Pro 3770 | English Manual - Page 5
assemble the weight system, make sure that all parts are oriented exactly as shown in the drawings. Tightening Parts Tighten all parts as you assemble them, unless instructed to do otherwise. Questions? If you have questions after reading the assembly instructions, please call our Customer Service - Weider Pro 3770 | English Manual - Page 6
that you have read all of the information on page 5. This brief introduction will save you much more time than it takes to read it. Locate and open the parts bags labeled "FRAME ASSEMBLY." See the inset drawing. Insert two 1 1/2" x 2 1/2" Inner Caps (83) and two 3/8" x 2" Carriage Bolts (92) into - Weider Pro 3770 | English Manual - Page 7
Caps (83) into the ends of the Butterfly Top Frame (33). Attach the Butterfly Top Frame (33) to the Butterfly Upright (1) with two 3/8" x 2 1/2" Bolts (87), a Support Plate (94), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 7 50 7 50 48 62 48 50 20 50 2 48 62 48 - Weider Pro 3770 | English Manual - Page 8
inset drawing. Insert two Weight Inserts (56) into each Weight (21). Set the two Weight Bumpers (51) over the holes in the corner bar of the Press Base (6). Slide the Weight Guides (15) through the Weight Bumpers (51) and the holes in the Press Base (6). Secure the Weight Guides to the Press Base - Weider Pro 3770 | English Manual - Page 9
13. Secure the Weight Guides (15) to the Press Top Frame (9) with two 3/8" x 1 3/4" Bolts (57) and two 13 3/8" Nylon Locknuts (50). Tighten the Nylon Locknuts (50) used in steps 2-13. 57 9 50 50 15 ARM ASSEMBLY 14 14. Locate and open the parts bag labeled "ARM ASSEMBLY - Weider Pro 3770 | English Manual - Page 10
15. Insert a 2" Square Inner Cap (28) into the end of the Butterfly Arm (10). Attach a Butterfly Handle (53) to the Butterfly Arm (10) with two 3/8" x 1" Bolts (84) and two 3/8" Flat Washers (48). Repeat this step with the other Butterfly Arm (10). 16. Lubricate a 3/8" x 3 1/4" Bolt (62). Attach the - Weider Pro 3770 | English Manual - Page 11
. The pulleys must be able to turn freely. Refer to the Cable ID Chart on page 26 for help identifying the cables. Locate and open the parts bags labeled "CABLE ASSEMBLY" and "PULLEYS." Locate the Butterfly Cable (73), which is the shorter cable of the two that have eyelets on both ends. Attach the - Weider Pro 3770 | English Manual - Page 12
23. Remove the preassembled 3/8" x 2" Bolts (54) from one set of Adjustable Pulley Plates (23). 23 Wrap the Butterfly Cable (73) around a 3 1/2" Pulley (24). Attach the 3 1/2" Pulley and a Cable Trap (25) between the top holes of the Adjustable Pulley Plates (23) with a 3/8" x 2" Bolt (54) and a - Weider Pro 3770 | English Manual - Page 13
the 3 1/2" Pulley to the rear bracket on the Press Top Frame (9) with a 3/8" x 2" Bolt (54) and a 3/8" Nylon Locknut (50). Be sure the Ab Cable is routed in the direction shown. Bracket 9 54 24 Wrap the Ab Pulley (47) around another 3 1/2" Pulley (24). Attach the 3 1/2" Pulley to the forward - Weider Pro 3770 | English Manual - Page 14
and 3/8" Flat Washer to the Bolt with a 3/8" Nylon Locknut (50). 3 24 54 4 72 50 Bracket 3 50 48 62 48 24 72 66 33. Insert the Weight Cable (72) through the hole in the Leg Lever (41), up around a 3 1/2" Pulley (24), back through the hole in the Leg Lever, and through the upper - Weider Pro 3770 | English Manual - Page 15
the bracket on the Butterfly Base (4) with a 3/8" x 1 3/4" Bolt (57) and a 3/8" Nylon Jamnut (63). Be sure that the Cable Trap is turned to hold the Cable in place. 24 25 57 38. Note: For convenience, the weights assembled 38 in step 9 are not shown in the following draw- ings. Wrap the - Weider Pro 3770 | English Manual - Page 16
25 47 23 50 24 72 40. Remove the preassembled 3/8" x 1 3/4" Bolts (57) 40 from the Small Pulley Plates (22). Wrap the Weight Cable (72) around a 3 1/2" Pulley (24). Attach the 3 1/2" Pulley between two Small Pulley Plates (22) with a 3/8" x 1 3/4" Bolt (57) and a 3/8" Nylon Locknut (50). 24 - Weider Pro 3770 | English Manual - Page 17
3 1/2" Pulley between the Small Pulley Plates (22) with a 3/8" x 1 3/4" Bolt (57) and a 3/8" Nylon Locknut (50) that was removed in step 40. Be sure the Leg Press Cable is routed so that it crosses from one side of the Press Base (6) to the other. 17 57 50 22 55 25 6 24 75 50 - Weider Pro 3770 | English Manual - Page 18
(25) to the 3/8" x 5 1/2" Bolt (55) on the indicated side of the Press Base (6) with the 3/8" Nylon Locknut (50). Be sure the Cable Trap is oriented to hold the Cable in place. Press a 2 1/2" Square Inner Cap (76) into the Press Base (6). 48. Remove the 3/8" Nylon Jamnut (63) from the indi- 48 - Weider Pro 3770 | English Manual - Page 19
51 51. Locate and open the parts bag labeled "SEAT ASSEMBLY." Attach a Seat (13) to the brackets on the Butterfly Seat Frame (14) using four 1/4" x 3/4" Bolts (49). Repeat this step with the other Seat (not shown) - Weider Pro 3770 | English Manual - Page 20
: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 25 and 26 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove the slack by tightening the cables. See TROUBLESHOOTING on page 24 - Weider Pro 3770 | English Manual - Page 21
ADJUSTMENTS The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise guide accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar, ab strap, or nylon strap, make sure that the - Weider Pro 3770 | English Manual - Page 22
desired set of holes in the Preacher Post (39). Reinsert the Large Adjustment Knob (46) through the holes in the Butterfly Front Leg and the holes in the Preacher Post. Turn the Large Adjustment Knob clockwise until tight. Note: When not using the Curl Pad (91), store it away from the weight system - Weider Pro 3770 | English Manual - Page 23
listed is the resistance for each butterfly arm. Note: The actual resistance at each weight station may vary due to differences in individual weight plates, as well as friction between the cables, pulleys, and weight guides. WEIGHT PLATES Top 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 PRESS - Weider Pro 3770 | English Manual - Page 24
TROUBLESHOOTING Inspect and tighten all parts each time the weight system is used. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable used on the weight - Weider Pro 3770 | English Manual - Page 25
and the Weight Cable (72). Use the diagrams to be sure that the Cables have been assembled correctly. The starting and ending points of each Cable have been labeled. The numbers show the proper route for each Cable. IMPORTANT: If the Cables have not been correctly routed, the weight system will not - Weider Pro 3770 | English Manual - Page 26
Weight Cable (72) 11 Cable ID 9 10 6 12-Weight Stack 8 7 5 4 2 72 47 75 73 3 1-Low Pulley 26 - Weider Pro 3770 | English Manual - Page 27
NOTES 27 - Weider Pro 3770 | English Manual - Page 28
2" x 3" Inner Cap (78) 2 1/2" Square Inner Cap (76) 1 1/2" Square Inner Cap (35) 1 1/2" x 2 1/2" Inner Cap (83) 2" Square Inner Cap (28) - Weider Pro 3770 | English Manual - Page 29
PART IDENTIFICATION CHART-Model No. WESY37531 R1003A 1/2" Flat Washer (11) 3/8" Flat Washer (48) Cable Clip (69) 1/2" Plain Nut (45) 1/2" Nylon Jamnut (36) 3/8" Nylon Locknut (50) 5/16" Nylon Locknut (64) 1/2" x 3/4" Spacer (97) 3/8" Nylon Jamnut (63) 5/16" Nylon Jamnut (34) 5/8" x 3/4" - Weider Pro 3770 | English Manual - Page 30
3/8" x 2" Carriage Bolt (92) 3/8" x 2" Bolt (54) 3/8" x 1 3/4" Bolt (57) 3/8" x 1 1/2" Button Head Bolt (98) 3/8" x 1" Bolt (84) 1" Tap Screw (80) 1/4" x 3/4" Bolt (49) 5/16" x 2 1/4" Shoulder Bolt (79) 3/8" x 2 1/2" Bolt (87) 5/16" x 2 3/4" Bolt (96) 3/8" x 2 3/4" Bolt (89) 3/8" x 3" Bolt (88) - Weider Pro 3770 | English Manual - Page 31
Bolt 93 2 5/8" x 1/2" Spacer 94 2 Support Plate 95 1 Plastic Weight Cover 96 4 5/16" x 2 3/4" Bolt 97 1 1/2" x 3/4" Spacer 98 1 3/8" x 1 1/2" Button Head Bolt # 1 User's Manual # 1 Exercise Guide Note: "#" indicates a non-illustrated part. Specifications are subject to change - Weider Pro 3770 | English Manual - Page 32
EXPLODED DRAWING-Model No. WESY37531 91 49 49 39 49 28 12 86 48 25 54 24 23 25 24 23 49 35 44 49 62 87 50 66 62 24 48 48 83 50 50 47 62 48 47 66 48 94 24 66 54 48 50 50 9 82 50 54 50 66 24 50 66 48 65 24 72 50 57 45 11 50 83 65 33 61 83 32 57 87 50 50 27 95 - Weider Pro 3770 | English Manual - Page 33
WEIDER® PRO 3770 weight system) • The SERIAL NUMBER of the product (see the front cover of this manual) • The KEY NUMBER and DESCRIPTION of the part(s) (see the PART replacing or repairing, at ICON's option, the product at one of its authorized service use, costs of removal the terms set forth herein.
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
 |
 |
USER'S MANUAL
QUESTIONS?
As a manufacturer, we are
committed to providing complete
customer satisfaction. If you
have questions, or if there are
missing parts, we will guarantee
complete satisfaction through
assistance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT
LINE. The technicians on
our customer hot line
will provide immediate
assistance, free of
charge.
CUSTOMER HOT LINE:
1-800-999-3756
Mon.–Fri., 6 a.m.–6 p.m. MST
Model No. WESY37531
Serial No.
Write the serial number in the space
above for future reference.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
Visit our website at
www.weiderfitness.com
new products, prizes,
fitness tips, and much more!
Serial Number Decal (Under Seat)