Home » Weider Manuals » Exercise and Fitness » Weider Pro 9950 » Manual Viewer

Weider Pro 9950 User Manual

Weider Pro 9950 Manual

Get Weider Pro 9950 PDF manuals and user guides

View all Weider Pro 9950 manuals

Add to My Manuals
Save this manual to your list of manuals

Weider Pro 9950 manual content summary:

Weider Pro 9950 | User Manual - Page 1
. Write the serial number in the space above. Serial Number Decal USER'S MANUAL SEARS, ROEBUCK AND CO. HOFFMAN ESTATES, IL 60179 CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. Patent Pending Visit our website at www
Weider Pro 9950 | User Manual - Page 2
TABLE OF CONTENTS IMPORTANT PRECAUTIONS 3 BEFORE YOU BEGIN 4 ASSEMBLY 5 ADJUSTMENT 23 WEIGHT RESISTANCE CHART 25 CABLE DIAGRAMS 26 TROUBLE-SHOOTING AND MAINTENANCE 27 ORDERING REPLACEMENT PARTS Back Cover FULL 90-DAY WARRANTY Back Cover Note: A PART LIST/EXPLODED DRAWING and a PART
Weider Pro 9950 | User Manual - Page 3
weight system. 1. Read all instructions in this manual and in the accompanying literature before using the weight system. 2. It is the responsibility of the owner to ensure that all users of the weight system are adequately informed of all precautions. 3. The weight system is intended for home use
Weider Pro 9950 | User Manual - Page 4
serial number can be found on a decal attached to the weight system (see the front cover of this manual). For your benefit, read this manual carefully before Please use the drawing below to familiarize yourusing the WEIDER® PRO 9950 weight system. If you self with the major parts and how they fit
Weider Pro 9950 | User Manual - Page 5
have questions after reading the assembly instructions, please call our HELPLINE at 1-800-736-6879. The Four Stages of the Assembly Process Frame Assembly-You will begin by assembling the base and the uprights that form the skeleton of the weight system. Cable Assembly-During this stage you will
Weider Pro 9950 | User Manual - Page 6
the information on page 5. Locate and open the parts bags labeled "FRAME ASSEMBLY 1 and 2." Press a 2" Square Inner Cap (59) into each end to the Butterfly Base (1) with two 5/16" x 2 3/4" Bolts (55), a Long Support Plate (34), and two 5/16" Nylon Locknuts (64). Do not tighten the Nylon Locknuts
Weider Pro 9950 | User Manual - Page 7
the weight system, slide a Weight Sleeve (27) onto each end of the weight tube on the Weight Carriage (28). Secure each Weight Sleeve with a Locking Pin (31). Note: The drawings in this manual show the Weight Sleeves attached. The Locking Pins will be found in the bag labled "SEAT ASSEMBLY". Repeat
Weider Pro 9950 | User Manual - Page 8
Carriage (28) onto each set of Weight Guides (33). Be sure the weight tubes are near the top of the Weight Carriages 7 28 Weight Tube 33 33 28 8. Attach the Top Frame (5) to the Butterfly Upright 8 (4) with two 3/8" x 2 3/4" Bolts (58), a Short Support Plate (26), and two 3/8" Nylon Locknuts
Weider Pro 9950 | User Manual - Page 9
a 3 1/2" Pulley (37) and a Cable Trap (44) to the Top Frame (5) with a 3/8" x 4" Bolt (91), the Pulley Support Plate (107), and a 3/8" Nylon Locknut two 5/16" Nylon Locknuts (64). Tighten all of the Nylon Locknuts (64, 74) used in steps 1 to 14. 13 Adjustment knob must be on this side 66 55 66
Weider Pro 9950 | User Manual - Page 10
15. Locate and open the parts bag labeled "ARM ASSEMBLY." Press a 2" Square Inner Cap (59) into each end of the Leg Lever (18). Press two Handgrips (99) onto the handle on the Right Butterfly Arm. 99 60 Assemble the Left Butterfly Arm (17) in the same manner. Handle 18 17 60 99 17.
Weider Pro 9950 | User Manual - Page 11
Cap (60) into the bottom of the Right Press Arm (16). Press two 19 Handgrips (99) onto the top and bottom of the handle. 16 Assemble the Left Press Arm (15) in the same 99 manner. Handle 60 99 102 92 15 20. Attach the Right Press Arm (16) to the
Weider Pro 9950 | User Manual - Page 12
. Locate and open the parts bag labeled "CABLE ASSEMBLY." For Cable identification and routing during steps 22 to 52, refer to the CABLE DIAGRAMS and CABLE ID CHART on page 26. Do not overtighten the nylon locknuts attaching the pulleys to the weight system; the pulleys must be able to turn freely
Weider Pro 9950 | User Manual - Page 13
and a 3/8" Nylon Locknut (74). 62 38 80 6 75 74 26. Wrap the Press Cable (80) around a 3 1/2" Pulley 26 (37). Attach the Pulley to the other side of (75), and a 3/8" Nylon Locknut (74). Make sure the Cable Trap is turned to hold the Cable in the groove of the Pulley. 13 65 14 75 80 37
Weider Pro 9950 | User Manual - Page 14
of the Pulley. Tighten the 3/8" Nylon Locknut (not shown) used in step 29. 44 22 80 37 32. Wrap the Press Cable (80) around a 3 1/2" Pulley 32 (37). Attach the Pulley and a Cable Trap (44) to the Support Brace (7) with a 3/8" x 3 3/4" Bolt (62), a 3/8" Washer (75), and a 3/8" Nylon Locknut
Weider Pro 9950 | User Manual - Page 15
Remove the 3/8" x 2 1/2" Bolt (78) from the top of 35 the indicated Weight Carriage (28). Attach the end of the Press Cable (80) to the Weight Carriage with the Bolt (78) and 3/8" Nylon Locknut (74). 36. Identify the Butterfly Cable (81); it is approximate- 36 ly 52" long and it has a loop on
Weider Pro 9950 | User Manual - Page 16
) to the other side of the bracket on the Butterfly Upright (4) with a 3/8" x 2 1/2" Bolt (78) and a 3/8" Nylon Locknut (74). Be sure the Long Cable Trap is turned to hold the Cable in the groove of the Pulley. 50 38 78 81 Bracket 74 4 81 37 74 44 79 43 78 38 81 50
Weider Pro 9950 | User Manual - Page 17
. Attach the Pulley and Pulley Covers to the Butterfly Upright (4) with a 3/8" x 4" Bolt (91), two 3/8" Washers (75), and a 3/8" Nylon Locknut (74). Be sure that the Cable is between the Pulley and the rod on the Upright, and that the ball is on the side shown. 42. Remove the two 3 1/2" Pulleys (37
Weider Pro 9950 | User Manual - Page 18
on the Top Frame (5) with a 3/8" x 2" Bolt (79) and a 3/8" Nylon Locknut (74). 5 74 83 79 37 Bracket 47. Attach the end of the Ab Cable (83) to the indicat- 47 ed Weight Carriage (28) with a 3/8" x 2 1/2" Bolt (78) and a 3/8" Nylon Locknut (74). 83 78 28 74 48. Identify the Leg Lever
Weider Pro 9950 | User Manual - Page 19
Bolt (79) and the 3/8" Nylon Locknut (74). 61 37 82 44 4 74 74 79 42 37 82 51. Wrap the Leg Press Cable (82) around a 3 1/2" 51 Pulley (37). Attach the Pulley and a Cable Trap (44) to the 3/8" x 5" Bolt (61) in the Butterfly Upright (4) with a 3/8" Nylon Locknut (74). Be sure that the
Weider Pro 9950 | User Manual - Page 20
bag labeled "SEAT ASSEMBLY." Press a 1 1/2" Square Inner Cap (100) into the bottom of a Seat Bracket (11). Press two 1" x 2" Inner Caps (70) into the ends of the Seat Bracket. Insert a 1/4" x 1 3/4" Carriage Bolt (93) into the center hole of a Support Plate (57). Attach the Support Plate to a Seat
Weider Pro 9950 | User Manual - Page 21
Caps (70) into the top and bottom of the Backrest Bracket. Insert a 1/4" x 1 3/4" Carriage Bolt (93) into the center hole of a Support Plate (57). Attach the Support Plate to Press Backrest (20) with two 1/4" x 3/4" Screws (90). Attach the Backrest to the Backrest Bracket (21) with the Carriage Bolt
Weider Pro 9950 | User Manual - Page 22
in ADJUSTMENTS, beginning on page 23 of this manual. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. Refer to the CABLE DIAGRAMS on page 26 for correct
Weider Pro 9950 | User Manual - Page 23
steps below explain how the weight system can be adjusted. Refer to the accompanying exercise guide to see the correct form for several exercise. Make sure all parts are properly tightened each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned with
Weider Pro 9950 | User Manual - Page 24
Pad (36). Store the Curl Pad away from the weight system when it is not being used. 36 35 52 59 ATTACHING THE LAT BAR Attach the Lat Bar (68) to the Leg Lever Cable (82) or Press Cable (not shown) with a Cable Clip (47). For some exercises, the Chain (45) should be attached between the Lat
Weider Pro 9950 | User Manual - Page 25
The chart below shows the approximate weight resistance at each exercise station. Note: The actual resistance at each station may vary due to differences in individual weight plates as well as friction between the cables, pulleys, and weight guides. The weight resistance listed for the Butterfly Arm
Weider Pro 9950 | User Manual - Page 26
traps do not touch or bind the Cables. Incorrect cable routing can damage the weight system. 5 3 1 2 Butterfly Cable (81) 4 6 13 5 2 2 12 1 1 3 Ab Cable (83) 6 5 4 3 7 4 3 14 Press Cable (80) 9 8 11 Leg Lever Cable (82) 2 5 1 10 7 Cable ID Chart (81) 52" 4 (82) 142.75
Weider Pro 9950 | User Manual - Page 27
PARTS on the back cover of this manual. The type of cable used on the weight system can stretch slightly when it is first used. If there is slack in the cables before resistance is felt, the cables should be tightened. Slack can be removed from the cables in two different ways: The Pulley Plates
Weider Pro 9950 | User Manual - Page 28
Model No. 831.159530 QUESTIONS? If you find that: • you need help assembling or operating the WEIDER® PRO 9950 weight system • a part is missing • or you need to schedule repair service call our toll-free HELPLINE 1-800-736-6879 Monday-Saturday, 7 am-7 pm Central Time (excluding holidays) The model
Weider Pro 9950 | User Manual - Page 29
this manual. Important: Some parts may have been pre-assembled for shipping purposes. If you cannot find a part in the parts bags, check to see if it has been pre-assembled. Note: Assembly is divided into four stages: 1) frame assembly; 2) arm assembly; 3) cable assembly; and 4) seat assembly. The
Weider Pro 9950 | User Manual - Page 30
2" Square Inner Cap (59) 1" x 2" Inner Cap (70) 1 1/2" Round Inner Cap (67) 1 3/4" Square Inner Cap (60) 1 1/2" Square Inner Cap (100) 1" CoverCap (86) 1" Retainer (85) 3/4" Round Inner Cap (73) 1" Inner Cap (32)
Weider Pro 9950 | User Manual - Page 31
PART LIST-Model No. 831.159530 R1001A 1/2" Nylon Locknut (95) 3/8" Nylon Locknut (74) 3/8" Nylon Jamnut (88) 5/16" Nylon Locknut (64) 5/16" Nylon Jamnut (105) 1/4" Nylon Locknut (106) 1/4" x 3/4" Screw (90) 3/8" x 1" Bolt (97) Bumper Screw (72) 1/4" x 1 3/4" Screw (98) 3/8" x 1 3/4" Bolt (103
Weider Pro 9950 | User Manual - Page 32
3/8" Washer (75) 3/8" SAE Washer (102) 5/16" Washer (66) 1/4" Washer (84) 5/16" x 2 1/2" Carriage Bolt (54) 3/8" x 2 1/2" Carriage Bolt (76) 5/16" x 2 3/4" Bolt (55) 3/8" x 2 3/4" Bolt (58) 3/8" x 3 1/4" Bolt (101) 3/8" x 3 1/2" Bolt (65) 1/2" x 3 1/2" Bolt (96) 3/8" x 3 3/4" Bolt (62) 3/8" x 4"
Weider Pro 9950 | User Manual - Page 33
REMOVE THIS PART LIST/EXPLODED DRAWING FROM THE MANUAL 81
Weider Pro 9950 | User Manual - Page 34
Weight Guide Long Support Plate Curl Post Curl Pad 3 1/2" Pulley "V"-Pulley Long Pad Tube Short Pad Tube Foam Pad Double U-bracket Pulley Plate Cable Trap Chain Press Pin Cable Clip Strap Pulley Cover Long Cable Nylon Locknut Pulley Support Plate User's Manual Exercise Guide Note: "#" indicates
Weider Pro 9950 | User Manual - Page 35
55 34 59 97 87 88 81 19 60 87 99 87 85 86 18 99 60 60 36 73 41 59 39 88 73 41 59 66 40 8 105 66 59 79 37 44 82 55 71 41 72 73 82 66 63 59 55 58 34 59 74 59 97 79 37 44 78 37 43 38 74 50 64 79 44 43 37 26 64 74 79 81 88 74 79 17 25 99 74 42 79 37 74 91 75 50