Weider Wedier Pro 9635 Canadian English Manual
Weider Wedier Pro 9635 Manual
 |
View all Weider Wedier Pro 9635 manuals
Add to My Manuals
Save this manual to your list of manuals |
Weider Wedier Pro 9635 manual content summary:
- Weider Wedier Pro 9635 | Canadian English Manual - Page 1
questions, or if there are missing parts, please call: 1-888-936-4266 Mon.-Fri. 8:00 until 17:00 EST (excluding holidays). CAUTION Read all precautions and instructions in this manual before using this equipment. Save this manual for future reference. USER'S MANUAL Visit our website at www.proform - Weider Wedier Pro 9635 | Canadian English Manual - Page 2
3 BEFORE YOU BEGIN 4 ASSEMBLY 5 HOW TO USE THE WEIGHT SYSTEM 22 WEIGHT RESISTANCE CHART 24 TROUBLESHOOTING AND MAINTENANCE 25 CABLE DIAGRAMS 26 ORDERING REPLACEMENT PARTS Back Cover LIMITED WARRANTY Back Cover Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached to - Weider Wedier Pro 9635 | Canadian English Manual - Page 3
parts. 9. The weight system is designed to support a maximum user weight of 136 kg (300 lbs). 13. Make sure that the cables remain on the pulleys at all times. If the cables bind while you are exercising, stop immediately and make sure that the cables are on all of the pulleys. Replace all cables - Weider Wedier Pro 9635 | Canadian English Manual - Page 4
the versatile WEIDER® PRO 9635 weight system. The weight system offers a system (see the front cover of this manual). Before reading further, please review the drawing below and familiarize yourself with the parts that are labeled. Lat Bar High Pulley Station VKR Arms Butterfly Arms ASSEMBLED - Weider Wedier Pro 9635 | Canadian English Manual - Page 5
assembly is completed. • Tighten all parts as you assemble them, unless instructed to do otherwise. • As you assemble the weight system, make sure all parts are oriented as shown in the drawings. • Assembly requires two people. • For help identifying small parts, use the PART IDENTIFICATION CHART - Weider Wedier Pro 9635 | Canadian English Manual - Page 6
) onto the M8 x 62mm Carriage Bolts (1) in the Base (4). Handtighten an M8 Nylon Locknut (3) onto each Carriage Bolt. Do not tighten the Locknuts yet. 3 3 3 1 3 3 5 1 FRAME ASSEMBLY 42 3 4 1 6 - Weider Wedier Pro 9635 | Canadian English Manual - Page 7
Upright (42) with two M8 x 67mm Bolts (11), two M8 Washers (8), and two M8 Nylon Locknuts (3). 4 11 11 55 8 3 11 3 56 42 74 FRAME ASSEMBLY 5. Slide the Rear Seat Frame (100) onto the indicated M8 x 62mm Carriage Bolts (1) in the Stabilizer (5). Hand-tighten two M8 Nylon Locknuts (3) onto the - Weider Wedier Pro 9635 | Canadian English Manual - Page 8
FRAME ASSEMBLY 7. Press a Weight Tube Bumper (64) into the end of a Weight Tube (63 Top Weight onto the front stack of Weights (25). Insert both Long Weight Guides (62) into the stack of Weights. Make sure that the holes in the Weight Guides are at the top, as shown. 65 Pin 63 62 Lubricate 64 Pin - Weider Wedier Pro 9635 | Canadian English Manual - Page 9
(61), and an M8 Nylon Locknut (3). Attach the upper ends of the Long Weight Guides (62) to the Top Frame (55) with an M8 x 150mm Bolt (60), 60 73 3 61 60 73 3 55 62 FRAME ASSEMBLY ARM ASSEMBLY 10. Locate and open the parts packet labeled "ARM ASSEMBLY." Lubricate an M10 x 83mm Bolt (67). Attach - Weider Wedier Pro 9635 | Canadian English Manual - Page 10
(17) with two M8 x 63mm Bolts (22) and two M8 Nylon Locknuts (3). Assemble the other Press Arm (46) in the same manner. 46 22 46 13. Identify Arm identification is very important for step 14. Attach a "V"-pulley (50) and a Long Cable Trap (31) to the Right Arm (48) with an M10 x 57mm Bolt (86) - Weider Wedier Pro 9635 | Canadian English Manual - Page 11
21 74 84 101 67 56 ARM ASSEMBLY CABLE ASSEMBLY 16. Locate and open the parts packets labeled "CABLE ASSEMBLY" and "PULLEYS." 16 During steps 16 through 35, refer to the CABLE DIAGRAMS on pages 26-27 of this manual to verify proper cable routing. Before beginning this section, fully unwind the - Weider Wedier Pro 9635 | Canadian English Manual - Page 12
and the M10 Nylon Locknut (not shown). 58 31 86 50 48 CABLE ASSEMBLY 21. Attach the Pulley Bracket (20) to the Top 21 Frame (55 ; the Pulley Bracket must be able to move freely. See the inset drawing. Route the High Cable 55 (58) over the 90mm Pulley (15) attached to the Pulley Bracket ( - Weider Wedier Pro 9635 | Canadian English Manual - Page 13
CABLE ASSEMBLY 22. See the inset drawing. Route the High Cable (58) under a 90mm Pulley (15). Attach the Pulley and a Cable Trap (66) to the upper hole in a Long "U"-bracket (57) with an M10 x 47mm Bolt (12) and an M10 Nylon Locknut (21). Make sure that the Cable is in the groove of the Pulley and - Weider Wedier Pro 9635 | Canadian English Manual - Page 14
CABLE ASSEMBLY 25. Route the Low Cable (23) under a 90mm Pulley (15). Attach the Pulley and a Cable 25 Trap (66) to the lower hole in the Front Upright (42) with an M10 x 92mm Bolt (88), an M10 Washer (9), and an M10 Nylon Locknut (21). Make sure that the Cable Trap is turned to hold the - Weider Wedier Pro 9635 | Canadian English Manual - Page 15
with an M8 x 45mm Bolt (24) and an M8 Nylon Locknut (3). 57 58 3 71 63 57 23 24 CABLE ASSEMBLY 58 71 8 3 30. Locate the Military Press Cable (72). Attach 30 the Military Press Cable to the other Small "U"-bracket (71) with an M8 Nylon Locknut (3) 3 and an M8 Washer (8). Do not completely - Weider Wedier Pro 9635 | Canadian English Manual - Page 16
a Cable Trap (66) to the Pivot Arm (101) with an M10 x 92mm Bolt (88), an M10 Washer (9), and an M10 Nylon Locknut (21). Make sure that the Locknut is on the side shown and that the Cable Trap is positioned to hold the Cable in place. 32 88 66 15 9 101 72 21 CABLE ASSEMBLY - Weider Wedier Pro 9635 | Canadian English Manual - Page 17
pivot easily. 15 57 72 72 21 57 103 9 15 A 66 12 B 101 104 3 72 CABLE ASSEMBLY 34. Locate the Leg Press Cable (99). Attach the 34 end of the Leg Press Cable to the Long "U"- bracket (57) with an M8 Nylon Locknut (3) and an M8 Washer (8). Do not completely tighten the Locknut. It - Weider Wedier Pro 9635 | Canadian English Manual - Page 18
an M8 Nylon Locknut (3) onto the Bolt. Make sure that the end of the Cable can pivot easily. 96 21 12 103 9 99 94 105 15 21 100 3 104 SEAT ASSEMBLY 36. Locate and open the parts packet labeled "SEAT ASSEMBLY." Insert an M6 x 63mm Carriage Bolt (92) through the center hole in a Seat - Weider Wedier Pro 9635 | Canadian English Manual - Page 19
SEAT ASSEMBLY 38. Orient the Front Backrest (41) as shown. 38 Attach the Backrest to the Front Upright (42) with two M6 x 63mm Screws (43) and two - Weider Wedier Pro 9635 | Canadian English Manual - Page 20
SEAT ASSEMBLY 42. Insert a Pad Tube (28) into the Front Seat 42 Frame (36). Slide a Pad (30) onto each end of the Pad Tube. 30 28 36 29 30 43. Locate and open the parts packet labeled 43 "VKR ASSEMBLY." Attach the Left VKR Arm (79) and the Right VKR Arm (80) to the VKR Upright (74) with - Weider Wedier Pro 9635 | Canadian English Manual - Page 21
problem. IMPORTANT: If the cables are not properly installed, they may be damaged when heavy weight is used. See the CABLE DIAGRAMS on page 26 and 27 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables. See TROUBLESHOOTING - Weider Wedier Pro 9635 | Canadian English Manual - Page 22
HOW TO USE THE WEIGHT SYSTEM The instructions below describe how each part of the weight system can be adjusted. Refer to the exercise poster accompanying this manual to see how the weight system should be set up for each exercise. IMPORTANT: When attaching the lat bar or nylon strap, make sure - Weider Wedier Pro 9635 | Canadian English Manual - Page 23
the M8 x 70mm Carriage Bolt (14) and the Seat Knob (40). For some exercises, the Seat (13) must be removed. First, make sure that the chain is not Chain (52) to the Low Cable (23) with a Cable Clip (53). Attach the other end of the Chain to the Eyebolt (35) with a Cable Clip. ADJUSTING THE LEG PRESS - Weider Wedier Pro 9635 | Canadian English Manual - Page 24
CHART This chart shows the approximate weight resistance at each weight station. "Top" refers to the 6.5 lb. (2.9 kg) top weight. The other numbers refer to the 12.5 lb. (5.7 kg) weight plates. The butterfly arm resistance listed the cables, pulleys, and weight guides. Note: 1 lb. = 0.454 kg 24 - Weider Wedier Pro 9635 | Canadian English Manual - Page 25
TROUBLESHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. The weight system can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use solvents. TIGHTENING THE CABLES Woven cable, the type of cable - Weider Wedier Pro 9635 | Canadian English Manual - Page 26
the proper routing of the High Cable (58), the Low Cable (23), the Military Press Cable (72), and the Leg Press Cable (99). Use the diagrams to be sure that the four cables and the cable traps have been assembled correctly. If the cables have not been correctly routed, the weight system will not - Weider Wedier Pro 9635 | Canadian English Manual - Page 27
Military Press Cable (72) and Leg Press Cable (99) 2 Military Press Cable (72) Rear Weight Stack-1 4 6-Pivot Arm 5 1-Long "U"-bracket 3 2 4-Rear Seat Frame 3 Leg Press Cable (99) 27 - Weider Wedier Pro 9635 | Canadian English Manual - Page 28
ORDERING REPLACEMENT PARTS To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give the following information: 1. the MODEL NUMBER of the product (WESY9635C.3) 2. the NAME of the product (WEIDER PRO 9635 weight system) 3. the SERIAL NUMBER of - Weider Wedier Pro 9635 | Canadian English Manual - Page 29
- Weider Wedier Pro 9635 | Canadian English Manual - Page 30
M8 x 67mm Bolt (11) M8 x 63mm Bolt (22) M6 x 63mm Screw (43) M6 x 63mm Carriage Bolt (92) M8 x 70mm Carriage Bolt (14) M8 x 70mm Bolt (75) M8 x 74mm Shoulder Bolt (103) M10 x 78mm Bolt (105) M10 x 83mm Bolt (67) M10 x 90mm Bolt (16) M10 x 92mm Bolt (88) M8 x 120mm Bolt (68) M8 x 150mm Bolt (60) - Weider Wedier Pro 9635 | Canadian English Manual - Page 31
PART IDENTIFICATION CHART M6 Nylon Locknut (2) M8 Nylon Locknut (3) M10 Nylon Locknut (21) M4 Washer (76) M6 Washer (10) M8 Washer (8) M4 x 16mm Self-tapping Screw (87) M6 x - Weider Wedier Pro 9635 | Canadian English Manual - Page 32
SAVE THIS PART LIST/EXPLODED DRAWING FOR FUTURE REFERENCE 81 - Weider Wedier Pro 9635 | Canadian English Manual - Page 33
PART LIST-Model No. Cable 100 1 Rear Seat Frame 101 1 Pivot Arm 103 2 M8 x 74mm Shoulder Bolt 104 2 13mm x 6mm Spacer 105 1 M10 x 78mm Bolt 106 1 90mm Reinforced Pulley # 1 User's Manual # 1 Exercise Guide # 1 Grease Packet Note: "#" indicates a non-illustrated part - Weider Wedier Pro 9635 | Canadian English Manual - Page 34
EXPLODED DRAWING-Model No. WESY9635C.3 R0605B 78 83 10 81 32 49 77 15 21 66 3 12 8 57 99 61 60 27 75 80 75 11 3 11 8 43 10 3 3 65 83 32 79 78 10 81 49 26 25 74 51 19 3 11 8 5 1 51 54 53 83 52 3 3 73 87 76 72 91 71 93 10 24 43 16 10 2 8 15 63 3 3 64 21 66 15
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
 |
 |
USER’S MANUAL
Model No. WESY9635C.3
Serial No.
Write the serial number in the space
above for reference.
Serial Number Decal (under seat)
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
QUESTIONS?
As a manufacturer, we are
committed to providing com-
plete customer satisfaction. If
you have questions, or if
there are missing parts,
please call:
1-888-936-4266
Mon.–Fri. 8:00 until 17:00
EST (excluding holidays).
www.weiderfitness.com
Visit our website at