Weider Wedier Pro 9635 Canadian English Manual - Page 7

Tighten all M8 Nylon Locknuts 3 used

Get Weider Wedier Pro 9635 PDF manuals and user guides View all Weider Wedier Pro 9635 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

4. Attach the Top Frame (55) to the VKR Upright (74) and the Leg Press Upright (56) with two M8 x 67mm Bolts (11) and two M8 Nylon Locknuts (3). Attach the Top Frame (55) to the Front Upright (42) with two M8 x 67mm Bolts (11), two M8 Washers (8), and two M8 Nylon Locknuts (3). 4 11 11 55 8 3 11 3 56 42 74 FRAME ASSEMBLY 5. Slide the Rear Seat Frame (100) onto the indicated M8 x 62mm Carriage Bolts (1) in the Stabilizer (5). Hand-tighten two M8 Nylon Locknuts (3) onto the Carriage Bolts. Attach the other end of the Rear Seat Frame (100) to the Leg Press Upright (56) with two M8 x 67mm Bolts (11), two M8 Washers (8), and two M8 Nylon Locknuts (3). Attach the Handle (82) to the Rear Seat Frame (100) with two M8 x 62mm Carriage Bolts (1) and two M8 Nylon Locknuts (3). Tighten all M8 Nylon Locknuts (3) used in steps 1-5. 6. Set two Weight Bumpers (19) on the bracket on the Base (4) as shown. Set two Weight Bumpers (19) on the bracket on the Stabilizer (5). Stack eight Weights (25) onto each set of Weight Bumpers (19). Make sure that the pin grooves are all on the same side of each stack of Weights. Be careful not to tip either stack of Weights (25) until step 8 is complete. 7 5 56 8 3 6 1 100 11 3 3 82 5 1 Pin Grooves 25 19 Bracket 25 5 Bracket 4 Pin Grooves 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
7
4.
Attach the Top Frame (55) to the VKR Upright
(74) and the Leg Press Upright (56) with two
M8 x 67mm Bolts (11) and two M8 Nylon
Locknuts (3).
Attach the Top Frame (55) to the Front
Upright (42) with two M8 x 67mm Bolts (11),
two M8 Washers (8), and two M8 Nylon
Locknuts (3).
5.
Slide the Rear Seat Frame (100) onto the
indicated M8 x 62mm Carriage Bolts (1) in the
Stabilizer (5). Hand-tighten two M8 Nylon
Locknuts (3) onto the Carriage Bolts.
Attach the other end of the Rear Seat Frame
(100) to the Leg Press Upright (56) with two
M8 x 67mm Bolts (11), two M8 Washers (8),
and two M8 Nylon Locknuts (3).
Attach the Handle (82) to the Rear Seat
Frame (100) with two M8 x 62mm Carriage
Bolts (1) and two M8 Nylon Locknuts (3).
Tighten all M8 Nylon Locknuts (3) used in
steps 1–5.
6.
Set two Weight Bumpers (19) on the bracket
on the Base (4) as shown. Set two Weight
Bumpers (19) on the bracket on the Stabilizer
(5).
Stack eight Weights (25) onto each set of
Weight Bumpers (19).
Make sure that the
pin grooves are all on the same side of
each stack of Weights.
Be careful not to tip either stack of
Weights (25) until step 8 is complete.
4
55
3
3
8
11
11
11
56
42
5
1
1
11
82
100
5
56
8
3
3
3
25
25
19
19
Bracket
Bracket
FRAME ASSEMBLY
74
Pin
Grooves
6
Pin
Grooves
5
4