Weslo Cadence A3 Treadmill English Manual - Page 8

Hold a Handrail 32 near the Right Upright 6. Feed

Get Weslo Cadence A3 Treadmill PDF manuals and user guides View all Weslo Cadence A3 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

5. Hold a Handrail (32) near the Right Upright (6). Feed the Wire Harness (22) into the hole near the lower end of the 5 Handrail and out the hole near the upper end of the Handrail. Note: It may be helpful to use needlenose pliers to pull the end of the Wire Harness out of the hole. 6 22 22 32 6. Open part bag C. Hold the Handrail (32) with the Wire 6 Harness (22) against the Right Upright (6). Hand tighten two 2" Bolts (12) with two 3/8" Star Washers (42) into the Handrail and the Right Upright. Be careful not to pinch the Wire Harness. Do not tighten the Bolts yet. 22 32 Attach the other Handrail (not shown) to the Left Upright (17) as described above. Note: There is not a wire on the left side. Do not tighten the Bolts yet. Orient a Weight Rack (71) as shown, and attach it to the Right Upright (6) with six Rack Screws (21). Start all six Screws before tightening them; do not overtighten the Screws. Attach the other Weight Rack (not shown) to the Left Upright (17) as described above. 17 22 42 12 6 71 21 21 21 7. Hold the Console Base (77) near the Handrails (32) (only one is shown). Insert the Wire Harness (22) through the 7 looped plastic tie and through the hole in the Console Base. Remove the tape holding the ends of the wires. Tape 77 22 32 Tie 22 22 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
8
5.
Hold a Handrail (32) near the Right Upright (6). Feed the
Wire Harness (22) into the hole near the lower end of the
Handrail and out the hole near the upper end of the
Handrail. Note: It may be helpful to use needlenose pliers
to pull the end of the Wire Harness out of the hole.
5
32
22
22
6
6.
Open part bag C.
Hold the Handrail (32) with the Wire
Harness (22) against the Right Upright (6). Hand tighten
two 2” Bolts (12) with two 3/8” Star Washers (42) into the
Handrail and the Right Upright.
Be careful not to pinch
the Wire Harness. Do not tighten the Bolts yet.
Attach the other Handrail (not shown) to the Left Upright
(17) as described above. Note: There is not a wire on the
left side.
Do not tighten the Bolts yet.
Orient a Weight Rack (71) as shown, and attach it to the
Right Upright (6) with six Rack Screws (21).
Start all six
Screws before tightening them; do not overtighten
the Screws.
Attach the other Weight Rack (not shown) to the Left
Upright (17) as described above.
6
17
22
32
22
71
21
6
12
21
21
42
7.
Hold the Console Base (77) near the Handrails (32) (only
one is shown). Insert the Wire Harness (22) through the
looped plastic tie and through the hole in the Console
Base. Remove the tape holding the ends of the wires.
7
77
Tie
Tape
22
22
32
22