Weslo Sport 100 Uk Manual - Page 7

slot in the Right Upright 37. Attach the Handrail Bracket

Get Weslo Sport 100 PDF manuals and user guides View all Weslo Sport 100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

2. Identify the Right Upright (37), which has a large round hole near the lower end, and the Left Upright (32). See drawing 2a. Make sure that there are two U-nuts (93) in the lower end of each Upright (32, 37). See drawing 2b. Have a second person hold the Base (55) so it is resting on the Wheels (34) as shown. Attach the Right and Left Uprights (32, 37) to the Base with four Upright Bolts (28) and four 5/16" Star Washers (68). Do not tighten the Bolts yet. Make sure that the large hole in the Right Upright is on the side shown, and that the two small holes in the Left Upright are on the side shown. In addition, make sure that the Base is oriented so that the Base Pads (31) are in the location shown. 2 2a Hole 37 2b Small Holes 37 93 55 32 68 Large Hole 28 31 34 32, 37 68 28 31 34 3. With the help of a second person, place the Frame (21) between the Uprights (32, 37). Feed the Wire Harness (53) into the large round hole near the lower end of the Right Upright (37), and then pull the Wire Harness out of the upper end as shown. See drawing 3a. Raise the Uprights (32, 37) to the vertical position. Hold an Upright Spacer (58) against one side of the Frame (21) as shown. Insert a Frame Bolt (36) into the indicated hole in the Upright Spacer and the Frame. Next, tighten a Spacer Screw (86) into the Upright Spacer and the Frame. Remove the Frame Bolt. Repeat on the other side of the Frame. With the help of a second person, carefully lift the Frame (21), and hold the Upright Spacers (58) between the Right Upright (37) and the Left Upright (not shown). Align the indicated hole in the Right Upright with the hole in the right Upright Spacer. Insert a Frame Bolt (36), with a 3/8" Star Washer (104), into the Right Upright and the Upright Spacer, and loosely thread the Upright Bolt into the Frame. Repeat this step on the left side of the treadmill. 4. With the help of a second person, tip the treadmill so the Base (not shown) is flat on the floor. Insert the tab on one of the Handrail Brackets (40) into the slot in the Right Upright (37). Attach the Handrail Bracket with a 3/4" Screw (77); be careful not to confuse the 3/4" Screws with the slightly larger Crossbar Screws (86, not shown). Attach the other Handrail Bracket to the Left Upright (not shown) as described above. 3 32 3a Hole 53 21 37 53 104 86 58 21 36 Holes 4 37 Slot Tab 40 77 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
7
2.
Identify the Right Upright (37), which has a large round
hole near the lower end, and the Left Upright (32).
See drawing 2a. Make sure that there are two U-nuts
(93) in the lower end of each Upright (32, 37).
See drawing 2b. Have a second person hold the Base
(55) so it is resting on the Wheels (34) as shown. Attach
the Right and Left Uprights (32, 37) to the Base with four
Upright Bolts (28) and four 5/16” Star Washers (68).
Do
not tighten the Bolts yet. Make sure that the large
hole in the Right Upright is on the side shown, and
that the two small holes in the Left Upright are on the
side shown. In addition, make sure that the Base is
oriented so that the Base Pads (31) are in the loca-
tion shown.
93
68
68
37
32
Large
Hole
31
34
55
28
37
Hole
2
2a
2b
31
34
36
104
21
3.
With the help of a second person, place the Frame (21)
between the Uprights (32, 37). Feed the Wire Harness
(53) into the large round hole near the lower end of the
Right Upright (37), and then pull the Wire Harness out of
the upper end as shown.
See drawing 3a. Raise the Uprights (32, 37) to the vertical
position. Hold an Upright Spacer (58) against one side of
the Frame (21) as shown. Insert a Frame Bolt (36) into the
indicated hole in the Upright Spacer and the Frame. Next,
tighten a Spacer Screw (86) into the Upright Spacer and
the Frame. Remove the Frame Bolt. Repeat on the other
side of the Frame.
With the help of a second person, carefully lift the Frame
(21), and hold the Upright Spacers (58) between the Right
Upright (37) and the Left Upright (not shown). Align the in-
dicated hole in the Right Upright with the hole in the right
Upright Spacer. Insert a Frame Bolt (36), with a 3/8” Star
Washer (104), into the Right Upright and the Upright
Spacer, and loosely thread the Upright Bolt into the Frame.
Repeat this step on the left side of the treadmill.
58
86
3
4. With the help of a second person, tip the treadmill so the
Base (not shown) is flat on the floor.
Insert the tab on one of the Handrail Brackets (40) into the
slot in the Right Upright (37). Attach the Handrail Bracket
with a 3/4” Screw (77);
be careful not to confuse the
3/4” Screws with the slightly larger Crossbar Screws
(86, not shown).
Attach the other Handrail Bracket to the
Left Upright (not shown) as described above.
40
37
77
Tab
Slot
4
Holes
3a
32, 37
Small
Holes
28
53
21
53
37
32
Hole