Whirlpool EDR4RXD1 Performance Data Sheet - Page 2

Linuron 140 ± 20% 20 ng/L >96.3% 96.3% Meprobamate 400 ± 20% 60 ng/L >95.2% 95.2% Metolachor 1400 ± 20% 200 ng/L >98.7% 98.7% Trimethoprim 140 ± 20% 20 ng/L >96.6% 96.5% Bisphenol 2000 ± 20% 300 ng/L >99.1% 99.1% Estrone 140 ± 20% 20 ng/L >96.6% 96.4% Nonylphenol 1400 ± 20% 200 ng/L >96.7% 96.6% Ibuprofen 400 ± 20% 60 ng/L >95.5% 95.3% Naproxen 140 ± 20% 20 ng/L >96.8% 96.7% Phenytoin 200 ± 20% 30 ng/L >95.5% 95.5% Turbidity 11 NTU ± 10% 0.5 NTU 98.8% 98.2% Chlorobenzene 2.0 ± 10% 0.1 mg/ L >99.9% 99.9% Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.70 gpm (2.65 Lpm). Pressure = 60 psig (413.7 kPa). Temp. = 68°F to 71.6°F (20°C to 22°C). Rated service capacity = 200 gallons (757 liters) with PID, 100 gallons (379 liters) without PID. The compounds certified under NSF 401 have been deemed as "emerging compounds/incidental contaminants." Emerging compounds/incidental contaminants compounds that have been detected in drinking water supplies at trace levels. While occurring at only trace levels, these compounds can affect the public acceptance/ perception of drinking water quality. � For installation, operation, and maintenance instructions please � The product is for cold water use only. refer to the Owners Manual. � The water system must be installed in compliance with state and � It is essential that operational, maintenance, and filter replacement local laws and regulations. requirements be carried out for the product to perform as advertised. Property damage can occur if all instructions are not followed. � Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on � The disposable cartridge must be changed at least every 6 months. disinfected waters that may contain filterable cysts. EPA Est. No. � Use replacement filter Part # EDR4RXD1/EDR4RXD1B. 2018 suggested retail price of $49.99 U.S.A./$49.95 Canada. Prices are 69625-CT-001 � Refer to the "Warranty" section (in the User Instructions or User subject to change without notice. Guide) for the Manufacturer's limited warranty, name and � The filter monitor system measures the amount of water that telephone number. passes through the filter and alerts you when it is time to replace the filter. To learn how to check the water filter status, see "Using Application Guidelines/Water Supply Parameters the Controls" or "Water Filtration System" in the User Instructions Water Supply Potable City or Well or User Guide. Water Pressure 30 psi - 120 psi � After changing the water filter, flush the water system. See "Water (207 kPa - 827 kPa) and Ice Dispensers" or "Water Dispenser" in the User Instructions Water Temperature 33°F - 100°F (0.6°C - 37.8°C) or User Guide. Service Flow Rate � These contaminants are not necessarily in your water supply. While 0.70 GPM (2.65 L/min.) @ 60 psi. (413.7 kPa) testing was performed under standard laboratory conditions, actual performance may vary. � Your water filtration system will withstand up to 120 pounds per � For installation, operation and maintenance instructions please refer Owner's Manual. square inch (psi) water pressure. If your water supply is higher than 80 psi, install a pressure reducing valve before installing the water filtration system. Consumer Support 1.800.442.9991 By Whirlpool Corporation 2000 North M63 Benton Harbor, MI 49022 Made in Taiwan. *Class I particle size: >0.5 to 1 um †Based on the use of Cryptosporidium parvum oocysts ††Fibers greater than 10 um in length ®NSF is a registered trademark of NSF International. 2 10-May-2021 11:18:45 EDT | RELEASED In some European factories the letter "W" of the part code mentioned herein will be automatically replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")