Whirlpool GCEM2990TQ Installation Instructions - Page 8
See Recessed Area and Closet Installation - parts manual
View all Whirlpool GCEM2990TQ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
GasSuppty Pressure Testing A 1/8"NPT minimum plugged tapping, accessible for gauge testing, must be installed immediately upstream of the gas supply connection to the dryer. The dryer must be disconnected from the gas supply piping system during any pressure testing of the system at test pressures in excess of 1/2psig. Plan installation to use the fewest number of elbows and turns. ExhaustAir Flow A. Better B. Good Allow as much room as possible when using elbows or making turns. Bend vent gradually to avoid kinking. Vent outlet is located at the center of the bottom dryer back. The vent can be routed up, down, left, right, behind the dryer or straight out the back of the dryer. Fire Hazard Use a heavy metal vent, Do not use a plastic vent, Do not use a metal foil vent. Failure to follow these instructions or fire. can result in death WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS. [] The dryer vent must not be connected into any gas vent, chimney, wall, ceiling, or a concealed space of a buiiding. [] Do not use an exhaust hood with a magnetic latch. [] Do not install fiexibte metal vent in enclosed walls, ceiiings or floors. [] 4" (10.2 cm) heavy metal vent and clamps must be used. [] Use clamps to seal all joints. Vent must not be connected or secured with screws or other fastening devices which extend into the interior of the vent. Do not use duct tape. iMPORTANT: Observe all governing codes and ordinances. Use a heavy metal vent. Do not use piastic or metal foil vent. Rigid metal vent is recommended to prevent crushing and kinking. Flexible metal vent must be fuIly extended and supported when the dryer is in its final position. Remove excess flexible meta! vent to avoid sagging and kinking that may resuIt in reduced airflow and poor performance. An exhaust hood shouId cap the vent to prevent rodents and insects from entering the home or business. Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes). if using an existing vent system, ctean Iint from the entire Iength of the system and make sure exhaust hood is not plugged with lint. Replace any plastic or metal foii vent with rigid metat or flexible metal vent. Vent System Length Maximum length of vent system depends upon the type of vent used, number of elbows and type of exhaust hood. The maximum length for both rigid and flexible vent is shown in the chart. Maximum Vent Length 4" (102 cm) Diameter Exhaust Hoods Rigid Metal Vent No. of 90 ° turns O 1 2 3 4 FlexibleMetalVent No. of 90° turns 0 1 2 3 4 Box Hood and Louvered Style 64 ft, (19,5 m) 54 ft. (16.5m) 44 ft. (13.4 m) 35 ft. (10,7 m) 27 ft. (8.2 m) Box Hood and Louvered Style 36 it, (11,0 m) 31 ft, (9,4 m) 27 ft, (8,2 m) 25 ft, (7.6 m) 23 ft, (7.0 m) Angled Hood Style 58 ft, (17,7 m) 48ft. (14_6m) 38ft. (11.6 m) 29ft. (8.8 m) 21ft. (&4 m) Angled Hood Style 28 ft, (8.5 m) 23 ft. (7,0 m) 19 ft, (5,8 m) 17 ft_ (5,2 m) 15 fL (4,6 m) For vent systems not covered by the vent specification chart, see Whirlpool Service Manual, "Exhausting Whirlpool Dryers," Part No. LIT603197, available from your Whirlpool parts distributor. if dryer is installed in a confined area, such as a bedroom, bathroom or closet, provision must be made for enough air for combustion and ventilation. (Check governing codes and ordinances.) See "Recessed Area and Closet Installation instructions" in the "Location Requirements" section A four-inch outlet hood is preferred. However, a 21/2'' (6.4 cm) outlet exhaust hood may be used. A 2!/2`' (6.4 cm) outlet creates greater back pressure than other hood types. For permanent installation, a stationary vent system is required.