Whirlpool GXU7130DXB Installation Guide - Page 8

3. To wire through wall: Mark a line distance "A" from the right of the centerline on the underside of the wall. Mark the point on this line that is ³⁄₄" (1.9 cm) from the underside of the cabinet. Drill a 1¹⁄₄" (3.2 cm) diameter hole through the rear wall at this point. 3. Use saber or keyhole saw to cut a rectangular opening in the wall for the vent. Cabinet front Centerline ³⁄₄" (1.9 cm) A Centerline A. 10⁷⁄₈" (27.6 cm) Style 1 - Cut Openings for 3¼" x 10" (8.3 cm x 25.4 cm) Rectangular Vent System Roof Venting To make a 4¹⁄₄" x 10½" (10.8 cm x 26.7 cm) rectangular cutout on the underside of cabinet top and bottom: 1. Mark lines ¹⁄₂" (1.3 cm) and 4³⁄₄" (12.1 cm) from the back wall on the centerline of the underside of cabinet. 2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline on the underside of cabinet. 3. Use saber or keyhole saw to cut a rectangular opening for vent. 4. Repeat steps 1-3 for the underside of the top of the cabinet. ³⁄₈" (0.9 cm) 3 9.8 cm) 5 ¹⁄₄" (13.3 cm) Style 2 - Cut Openings for 3¼" x 10" (8.3 x 25.4 cm) Rectangular Vent to Round Vent Transition Roof Venting To make a 4¹⁄₄" x 10½" (10.8 cm x 26.7 cm) rectangular cutout on the underside of cabinet bottom: 1. Mark lines ¹⁄₂" (1.3 cm) and 4³⁄₄" (12.1 cm) from the back wall on the centerline of the underside of cabinet. 2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline on the underside of cabinet. 3. Use saber or keyhole saw to cut a rectangular opening for vent. *¹⁄₂" (1.3 cm) Cabinet cutouts *¹⁄₂" (1.3 cm) *4³⁄₄" (12.1 cm) 5¹/₄" (13.3 cm) 5¹/₄" (13.3 cm) *From wall, not cabinet frame Wall Venting To make a 3½" x 10½" (8.9 cm x 26.7 cm) rectangle in the wall: 1. Make 2 lines by measuring ³⁄₈" (0.9 cm) and 3⁷⁄₈" (9.8 cm) down from underside of cabinet and mark on the centerline on the back wall. 2. Mark lines 5¼" (13.3 cm) to the right and left of the centerline on the wall. *4³⁄₄" (12.1 cm) 5¹/₄" (13.3 cm) 5¹/₄" (13.3 cm) *From wall, not cabinet frame To make a circular vent opening on the underside of the cabinet top: 1. Mark a centerline on the underside of the top of cabinet. 2. Mark a line 5" (12.7 cm) from the back wall on the underside of the top of cabinet. 3. Use a compass or a circle template to draw a circle with a diameter that is ¼" (0.64 cm) larger than the vent. 4. Use saber or keyhole saw to cut the circular vent opening. Circular vent opening *5" (12.7 cm) Cabinet cutouts *From wall, not cabinet frame 8