Whirlpool WED6600V Use and Care Guide - Page 16

Level Dryer

Get Whirlpool WED6600V PDF manuals and user guides View all Whirlpool WED6600V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

5. Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector. 6. Attach straight end of long hose to "Y" connector. 7. Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand until it is seated on connector. 8. Using pliers, tighten the couplings with an additional twothirds turn. Level Dryer Check the levelness of the dryer by first placing a level on the top of the dryer near the console. A A. Inlet to cold water NOTE: Do not overtighten. Damage to the coupling can result. 9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector. 10. Using pliers, tighten the coupling with an additional twothirds turn. Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the levelness from front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. NOTE: Do not overtighten. Damage to the coupling can result. 11. Check that the water faucets are on. 12. Check for leaks around "Y" connector, faucet and hoses. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
16
5.
Attach “Y” connector to brass male end of small hose. Screw
on coupling by hand until it is seated on connector.
6.
Attach straight end of long hose to “Y” connector.
7.
Attach washer cold inlet hose to other end of “Y” connector.
Screw on coupling by hand until it is seated on connector.
8.
Using pliers, tighten the couplings with an additional two-
thirds turn.
NOTE:
Do not overtighten. Damage to the coupling can
result.
9.
Attach angled end of long hose to fill valve at bottom of dryer
back panel. Screw on coupling by hand until it is seated on fill
valve connector.
10.
Using pliers, tighten the coupling with an additional two-
thirds turn.
NOTE:
Do not overtighten. Damage to the coupling can
result.
11.
Check that the water faucets are on.
12.
Check for leaks around “Y” connector, faucet and hoses.
Level Dryer
Check the levelness of the dryer by first placing a level on the top
of the dryer near the console.
Then, by placing a level in the crease on the side of the dryer
between the top of the dryer and the dryer cabinet, check the
levelness from front to back.
If the dryer is not level, prop up the dryer using a wood block.
Use a wrench to adjust the legs up or down and check again for
levelness.
A. Inlet to cold water
A