Whirlpool WED7500VW Dimension Guide - Page 1
Whirlpool WED7500VW Manual
UPC - 883049138251
View all Whirlpool WED7500VW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
® Electric Dryer PRODUCT MODEL NUMBERS WED7500V Electrical: A four-wire or three-wire, single phase, 120/240-volt, 60 Hz, AC-only, electrical supply (or 120/208-volt electrical supply, if specified on the serial/rating plate) is required on a separate 30 amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Exhaust venting: Exhaust your dryer to the outside. 4" (10.2 cm) diameter vent is required. Heavy metal exhaust vent must be used. Do not use plastic or metal foil vent. Exhaust outlet hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust. OVERALL DIMENSIONS 39" (99.1 cm) 23 59.37 cm) *23 ¼" (60.3 cm) 33 ¼" (84.45 cm) * Most installations require a minimum 5 -1/2" (14.0 cm) clearance behind the dryer for the exhaust vent with elbows. CUSTOM UNDERCOUNTER, RECESSED AREA AND CLOSET INSTALLATION Custom undercounter installation - Dryer only 0" (0 cm) 33¹⁄₄" min. (84.45 cm) 0" (0 cm) 23³⁄₈" (59.37 cm) 0" (0 cm) Recessed or closet installation - Dryer only 14" (35.6 cm) 48 in.2 (310 cm2) 18"(45.7 cm) 3" (7.6 cm) 3" (7.6 cm) 0" 24 in.2 (155 cm2) 0" 1" (2. 5 cm) A (0 cm) (0 cm) B C A. Side view - closet or confined area B. Recessed area C. Closet door with vents 3" (7.6 cm) Recessed or closet installation - Stacked with stack kit (Accessory) 12" (30.5 cm) DRYER 3" (7.6 cm) 48 in.2 (310 cm2) 3" (7.6 cm) EXHAUST VENTING Vent material • Use a heavy metal vent. Do not use plastic or metal foil vent. • 4" (10.2 cm) heavy metal exhaust vent and clamps must be used. Rigid metal vent • For best drying performance, rigid metal vents are recommended. • Rigid metal vent is recommended to avoid crushing and kinking. 4" 10.2 cm 4" (10.2 cm) heavy metal exhaust vent Flexible metal vent • Flexible metal vents are acceptable only if accessible for cleaning. • Flexible metal vent must be fully extended and supported when the dryer is in its final location. • Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance. Exhaust Recommended hood styles are shown here. B A 4" (10.2 cm) 4" (10.2 cm) A. Louvered hood style B. Box hood style The angled hood style (shown here) is acceptable. 4" (10.2 cm) WASHER 24 in.2 (155 cm2) 0" (0 cm) 0" (0 cm) 1" (2.5 cm) A B A. Recessed area B. Side view - closet or confined area C. Closet door with vents 3" (7.6 cm) C 2½" (6.4 cm) • An exhaust hood should cap the vent to keep rodents and insects from entering the home. • Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.). • Do not use an exhaust hood with a magnetic latch. Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation our products, we reserve the right to change materials and specifications without notice. Instructions packed with product. Specifications subject to change without notice. Ref. W10189310 04-02-08