Home » Whirlpool Manuals » Laundry Dryers » Whirlpool WED9450WR » Manual Viewer

Whirlpool WED9450WR Installation Instructions - Page 9

Venting Requirements.

View all Whirlpool WED9450WR manuals

Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

4-wire connection: Direct wire IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections. (251"mm) Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 5" (127 mm) of outer covering from end of cable, leaving bare 5" (127 mm) ground wire at 5" (127 mm). Cut 11/2" (38 mm) from 3 remaining wires. Strip insulation back 1" (25 mm). Shape ends of wires into a hook shape. When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown. 1. Remove center silver-colored terminal block screw. 2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze hooked ends together. Tighten screw. B A C D E 3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw. A D E B F C A. External ground conductor screw B. Ground wire (green or bare) of power supply cable C. ¾" (19 mm) UL listed strain relief D. Center silver-colored terminal block screw E. Neutral ground wire F. Neutral wire (white or center wire) 4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws. 5. Tighten strain relief screw. 6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. 7. You have completed your electrical connection. Now go to "Venting Requirements." 3-wire connection: Power supply cord Use where local codes permit connecting cabinet-ground conductor to neutral wire. B D E A A. External ground conductor screw - Dotted line shows position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw. B. Center silver-colored terminal block screw C. Neutral ground wire D. Neutral wire (white or center wire) E. ¾" (19 mm) UL listed strain relief C GF A. 3-wire receptacle (NEMA type 10-30R) B. 3-wire plug C. Neutral prong D. Spade terminals with up turned ends E. ¾" (19 mm) UL listed strain relief F. Ring terminals G. Neutral (white or center wire) 1. Loosen or remove center silver-colored terminal block screw. 9

Section	Page
ELECTRIC Dryer Installation Instructions U.S.A. ONLY	1
Para una version de estas intrucciones en español, visite www.Whirlpool.com	1
Table of Contents	1
Dryer Safety	1
INSTALLATION REQUIREMENTS	2
Tools and Parts	2
Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.	2
Flat-blade screwdriver	2
#2 Phillips screwdriver	2
Adjustable wrench that opens to 1\	2
Level	2
Wire stripper (direct wire installations)	2
Vent clamps	2
Caulking gun and compound (for installing new exhaust vent)	2
Tin snips (new vent installations)	2
¼\	2
Tape measure	2
Pliers	2
Parts supplied	2
Non-Steam Models	2
4 Leveling legs	2
Steam Models	2
Remove parts package from dryer drum. Check that all parts are included.	2
NOTE: Do not use leveling legs supplied with dryer if installing on a pedestal.	2
Parts needed	2
Check local codes. Check existing electrical supply and venting. See “Electrical Requirements” and “Venting Requirements” before purchasing parts.	2
Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the “Assistance or Service” section in your Use and Care Guide.	2
Optional Equipment	2
Refer to your Use and Care guide for information about the accessories available for your dryer.	2
Location Requirements	3
You will need	3
A location that allows for proper exhaust installation. See “Venting Requirements.”	3
A separate 30-amp circuit.	3
If you are using a power supply cord, a grounded electrical outlet located within 2 ft (610 mm) of either side of the dryer. See “Electrical Requirements.”	3
A sturdy floor to support the total dryer weight of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.	3
A level floor with a maximum slope of 1\	3
For a garage installation, you will need to place the dryer at least 18\	3
Steam models only: Cold water faucets located within 4 ft (1.2 m) of the dryer, and water pressure of 20-100 psi (137.9-689.6 kPa). You may use the cold water supply from your washer using the “Y” connector provided.	3
Do not operate your dryer at temperatures below 45ºF (7ºC). At lower temperatures, the dryer might not shut off at the end of an automatic sensor cycle. This can result in longer drying times.	3
The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.	3
Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.	3
Installation clearances	3
The location must be large enough to allow the dryer door to open fully.	3
Dryer Dimensions	3
Steam (Electric or Gas)	3
Non-Steam (Electric or Gas)	3
A	3
38\	3
38\	3
B	3
32 9/16\	3
31 1/2\	3
C	3
27\	3
27\	3
D	3
52 9/16\	3
51 1/2\	3
NOTE: Most installations require a minimum 5\	3
Installation spacing for recessed area or closet installation	3
The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0\	3
Additional spacing should be considered for ease of installation and servicing.	3
Additional clearances might be required for wall, door, and floor moldings.	3
Additional spacing should be considered on all sides of the dryer to reduce noise transfer.	3
For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.	3
Companion appliance spacing should also be considered.	3
Custom undercounter installation - Dryer only	4
Steam (Electric or Gas)	4
Non-Steam (Electric or Gas)	4
A	4
0\	4
0\	4
B	4
38\	4
38\	4
C*	4
1\	4
1\	4
D	4
27\	4
27\	4
E*	4
1\	4
1\	4
NOTE: Some models are not recommended for undercounter installation.	4
Closet installation - Dryer only	4
Steam (Electric or Gas)	4
Non-Steam (Electric or Gas)	4
A*	4
1\	4
1\	4
B	4
32 9/16\	4
31 1/2\	4
C**	4
5\	4
5\	4
Recessed or closet installation - Dryer on pedestal	4
Steam (Electric or Gas)	4
Non-Steam (Electric or Gas)	4
A	4
1\	4
1\	4
B	4
27\	4
27\	4
C	4
1\	4
1\	4
D*	4
1\	4
1\	4
E	4
32 9/16\	4
31 1/2\	4
F**	4
5\	4
5\	4
** For side or bottom venting, 0\	4
NOTE: Some models are not recommended for recessed or closet installation.	4
Recommended installation spacing for cabinet installation	5
NOTE: Some models are not recommended for cabinet installation.	5
For cabinet installation, with a door, minimum ventilation openings in the top of the cabinet are required.	5
Steam (Electric or Gas)	5
Non-Steam (Electric or Gas)	5
A*	5
7\	5
7\	5
B*	5
7\	5
7\	5
C*	5
9\	5
9\	5
D**	5
5\	5
5\	5
E	5
32 9/16\	5
31 1/2\	5
F*	5
1\	5
1\	5
G	5
1\	5
1\	5
H	5
27\	5
27\	5
I	5
1\	5
1\	5
** For side or bottom venting, 0\	5
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer	5
The dimensions shown are for the recommended spacing.	5
Steam (Electric or Gas)	5
Non-Steam (Electric or Gas)	5
A	5
5 ½\	5
5\	5
NOTE: Some models are not recommended for stacked recessed or closet installation.	5
Mobile home - Additional installation requirements	5
This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, H...	5
Mobile home installations require:	5
All Dryers:	5
Metal exhaust system hardware, which is available for purchase from your dealer.	5
Special provisions must be made in mobile homes to introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.	5
Electric DRYER POWER HOOKUP	6
Electrical Requirements - U.S.A. Only	6
It is your responsibility	6
To contact a qualified electrical installer.	6
To be sure that the electrical connection is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70- latest edition and all local codes and ordinances.	6
To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 120/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line....	6
Do not use an extension cord.	6
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.	6
Electrical Connection	6
To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.	6
This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical s...	6
If local codes do not permit the connection of a neutral ground wire to the neutral wire, see “Optional 3-wire connection” section.	6
A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, (2) mobile ...	6
If using a power supply cord:	6
Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:	6
A UL listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.	6
A UL listed strain relief.	6
If your outlet looks like this:	6
Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The gr...	6
If your outlet looks like this:	6
Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.	6
If connecting by direct wire:	6
Power supply cable must match power supply (4-wire or 3-wire) and be:	6
Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.	6
10-gauge solid copper wire (do not use aluminum) at least 5 ft (1.52 m) long.	6
Electrical Connection - U.S.A. Only	7
1. Disconnect Power.	7
2. Remove the hold-down screw and terminal block cover.	7
3. Install strain relief.	7
Remove the screws from a 3/4\	7
Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further t...	7
Unscrew the removable conduit connector and any screws from a 3/4\	7
Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.	8
4. Now complete installation following instructions for your type of electrical connection:	8
Electrical Connection Options	8
If your home has:	8
And you will be connecting to:	8
Go to Section	8
4-wire receptacle (NEMA Type 14-30R)	8
A UL listed, 120/ 240-volt minimum, 30-amp, dryer power supply cord*	8
4-wire connection: Power supply cord	8
4-wire direct	8
A fused disconnect or circuit breaker box*	8
4-wire connection: Direct Wire	8
3-wire receptacle (NEMA type 10-30R)	8
A UL listed, 120/ 240-volt minimum, 30-amp, dryer power supply cord*	8
3-wire connection: Power supply cord	8
3-wire direct	8
A fused disconnect or circuit breaker box*	8
3-wire connection: Direct Wire	8
4-wire connection: Power supply cord	8
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.	8
1. Remove center silver-colored terminal block screw.	8
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.	8
3. Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.	8
4. Connect the other wires to outer terminal block screws. Tighten screws.	8
5. Tighten strain relief screws.	8
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	8
7. You have completed your electrical connection. Now go to “Venting Requirements.”	8
4-wire connection: Direct wire	9
IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do not permit the use of 3-wire connections.	9
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.	9
Strip 5\	9
When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.	9
1. Remove center silver-colored terminal block screw.	9
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block....	9
3. Connect ground wire (green or bare) of direct wire cable to external ground conductor screw. Tighten screw.	9
4. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	9
5. Tighten strain relief screw.	9
6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	9
7. You have completed your electrical connection. Now go to “Venting Requirements.”	9
3-wire connection: Power supply cord	9
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	9
1. Loosen or remove center silver-colored terminal block screw.	9
2. Connect neutral wire (white or center wire) of power supply cord to the center silver-colored terminal screw of the terminal block. Tighten screw.	10
3. Connect the other wires to outer terminal block screws. Tighten screws.	10
4. Tighten strain relief screws.	10
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	10
6. You have completed your electrical connection. Now go to “Venting Requirements.”	10
3-wire connection: Direct wire	10
Use where local codes permit connecting cabinet-ground conductor to neutral wire.	10
Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed.	10
Strip 31/2\	10
When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.	10
1. Loosen or remove center silver-colored terminal block screw.	10
2. Place the hooked end of the neutral wire (white or center wire) of direct wire cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw.	10
3. Place the hooked ends of the other direct wire cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.	10
4. Tighten strain relief screw.	10
5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.	10
6. You have completed your electrical connection. Now go to “Venting Requirements.”	10
Optional 3-wire connection	10
Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.	10
1. Remove center silver-colored terminal block screw.	10
2. Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver- colored terminal block screw. Tighten screw.	10
3. Connect the other wires to outer terminal block screws. Tighten screws.	11
4. Tighten strain relief screws.	11
5. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.	11
Venting	11
Venting Requirements	11
WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS.	11
IMPORTANT: Observe all governing codes and ordinances.	11
The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling, attic, crawlspace, or a concealed space of a building. Only rigid or flexible metal vent shall be used for exhausting.	11
If using an existing vent system	11
Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.	11
Replace any plastic or metal foil vent with rigid or flexible heavy metal vent.	11
Review vent system chart. Modify existing vent system if necessary to achieve the best drying performance.	11
If this is a new vent system	11
Vent material	11
Use a heavy metal vent. Do not use plastic or metal foil vent.	11
4\	11
Rigid metal vent	11
For best drying performance, rigid metal vents are recommended.	11
Rigid metal vent is recommended to avoid crushing and kinking.	11
Flexible metal vent	11
Flexible metal vents are acceptable only if accessible for cleaning.	11
Flexible metal vent must be fully extended and supported when the dryer is in its final location.	11
Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance.	11
Do not install flexible metal vent in enclosed walls, ceilings, or floors.	11
The total length of flexible metal vent should not exceed 7¾ ft. (2.4 m).	11
Elbows	11
Good	11
Better	11
Clamps	11
Use clamps to seal all joints.	11
Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct and catch lint. Do not use duct tape.	11
Exhaust	12
An exhaust hood should cap the vent to keep rodents and insects from entering the home.	12
Exhaust hood must be at least 12\	12
Do not use an exhaust hood with a magnetic latch.	12
Plan Vent System	12
Choose your exhaust installation type	12
Recommended exhaust installations	12
Typical installations vent the dryer from the rear of the dryer. Other installations are possible.	12
Optional exhaust installations	12
This dryer can be converted to exhaust out the right side, left side or through the bottom. If you prefer, you may contact your local dealer to have the dryer converted.	12
Alternate installations for close clearances	12
Venting systems come in many varieties. Select the type best for your installation. Two close-clearance installations are shown. Refer to the manufacturer’s instructions.	12
NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the “Assistance or Service” section to order.	12
Over-the-Top Installation:	12
Periscope Installation (For use with dryer vent to wall vent mismatch):	12
Special provisions for mobile home installations	13
The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.	13
Determine vent path	13
Select the route that will provide the straightest and most direct path outdoors.	13
Plan the installation to use the fewest number of elbows and turns.	13
When using elbows or making turns, allow as much room as possible.	13
Bend vent gradually to avoid kinking.	13
Use the fewest 90° turns possible.	13
Determine vent length and elbows needed for best drying performance	13
Use the following vent system chart to determine type of vent material and hood combinations acceptable to use.	13
Shorten the life of the dryer.	13
Reduce performance, resulting in longer drying times and increased energy usage.	13
The vent system chart provides venting requirements that will help to achieve the best drying performance.	13
Vent system chart	13
NOTE: Side and bottom exhaust installations have a 90º turn inside the dryer. To determine maximum exhaust length, add one 90º turn to the chart.	13
Number 90º elbows	13
Type of vent	13
Box /louvered hoods	13
Angled hoods	13
0	13
Rigid metal	13
1	13
Rigid metal	13
2	13
Rigid metal	13
44 ft (13.4 m)	13
38 ft (11.6 m)	13
3	13
Rigid metal	13
35 ft (10.7 m)	13
29 ft (8.8 m)	13
4	13
Rigid metal	13
27 ft (8.2 m)	13
21 ft (6.4 m)	13
Install Vent System	13
1. Install exhaust hood. Use caulking compound to seal exterior wall opening around exhaust hood.	13
2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4\	13
3. Run vent to dryer location. Use the straightest path possible. See “Determine vent path” in “Plan Vent System.” Avoid 90º turns. Use clamps to seal all joints. Do not use duct tape, screws or other fastening devices that extend into the i...	13
Install Leveling Legs	13
1. To protect the floor, use a large flat piece of cardboard from the dryer carton. Place cardboard under the entire back edge of the dryer.	13
2. Firmly grasp the body of the dryer (not the console panel). Gently lay the dryer on the cardboard. See illustration.	13
3. Examine the leveling legs. Find the diamond marking.	13
4. Screw the legs into the leg holes by hand. Use a wrench to finish turning the legs until the diamond marking is no longer visible.	13
5. Place a carton corner post from dryer packaging under each of the 2 dryer back corners. Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location. Leave enough room to connect the exhaust vent.	13
Connect Vent	13
1. Using a 4\	13
2. Move dryer into its final location. Do not crush or kink vent.	13
3. Once the exhaust vent connection is made, remove the corner posts and cardboard.	13
Connect Inlet Hose (Steam Models)	14
The dryer must be connected to the cold water faucet using the new inlet hoses. Do not use old hoses.	14
1. Turn cold water faucet off and remove washer inlet hose.	14
2. Remove old rubber washer from inlet hose and replace with new rubber washer provided. If space permits, attach the brass female end of the “Y” connector to the cold water faucet.	14
3. Attach short hose to cold water faucet. Screw on coupling by hand until it is seated on faucet.	14
4. Using pliers, tighten the couplings with an additional two-thirds turn.	14
5. Attach “Y” connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector.	14
6. Attach straight end of long hose to “Y” connector.	14
7. Attach washer cold inlet hose to other end of “Y” connector. Screw on coupling by hand until it is seated on connector.	14
8. Using pliers, tighten the couplings an additional two-thirds turn.	14
9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector.	14
10. Using pliers, tighten the coupling an additional two-thirds turn.	14
11. Check that the water faucets are on.	14
12. Check for leaks around “Y” connector, faucet, and hoses.	14
Level Dryer	14
Check the levelness of the dryer. Check levelness first side to side, then front to back.	14
If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.	14
Complete Installation	14
1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	14
2. Check that you have all of your tools.	14
3. Dispose of/recycle all packaging materials.	14
4. Check the dryer’s final location. Be sure the vent is not crushed or kinked.	14
5. Check that the dryer is level. See “Level Dryer.”	14
6. Remove the blue protective film on the console and any tape remaining on the dryer.	14
7. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.	14
8. Read “Dryer Use.”	14
9. For power supply cord installation, plug into a grounded outlet. For direct wire installation, turn on power.	14
Steam Models Only:	14
10. Be sure the water faucets are on.	14
11. Check for leaks around “Y” connector, faucet, and hoses.	14
12. If you live in a hard water area, use of a water softener is recommended to control the buildup of scale through the water system in the dryer. Over time, the buildup of lime scale may clog different parts of the water system, which will reduce p...	14
All Models:	14
13. Select a Timed Dry heated cycle, and start the dryer. Do not select the Air Only Temperature setting.	14
This dryer automatically runs an installation diagnostic routine at the start of its first cycle.	14
If you receive an L2 code, there may be a problem with your home power supply keeping the dryer’s heater from turning on. See “Troubleshooting.”	14
If you receive an AF code, your dryer vent may be crushed or blocked. See “Troubleshooting.”	14
NOTE: You may notice an odor when the dryer is first heated. This odor is common when the heating element is first used. The odor will go away.	14
troubleshooting	15
First try the solutions suggested here and possibly avoid the cost of a service call...	15
Dryer Operation	15
Dryer will not run	15
Has a household fuse blown, or has a circuit breaker tripped? There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses are intact and tight, or that both circuit breakers have not tripped. Replace the fuse or reset the ...	15
Is the correct power supply available? Electric dryers require 240-volt power supply. Check with a qualified electrician.	15
Was a regular fuse used? Use a time-delay fuse.	15
No heat	15
Has a household fuse blown, or has a circuit breaker tripped? The drum may be turning, but you may not have heat. Electric dryers use 2 household fuses or circuit breakers. Replace the fuse or reset the circuit breaker. If the problem continues, call...	15
Dryer displaying code message	15
“PF” (power failure), check the following: Was the drying cycle interrupted by a power failure? Press and hold START to restart the dryer.	15
“L2” Diagnostic Code (low or no line voltage condition): The drum will turn, but there may be a problem with your home power supply keeping the dryer's heater from turning on. The dryer will continue to run when this diagnostic code is present. P...	15
“AF” (low airflow condition): The dryer will continue to run when this diagnostic code is present. Press any key to clear the code from the display and return to the estimated time remaining.	15
Try the following: Clean lint screen.	15
Check to see if the vent run from the dryer to the wall is crushed or kinked.	15
Confirm the vent run from the dryer to the wall is free of lint and debris.	15
Confirm the exterior vent exhaust hood is free of lint and debris.	15
Confirm your vent system falls within the recommended run length and number of elbows for the type of vent you are using. Refer to “Plan Vent System” for details.	15
Select a Timed Dry heated cycle, and restart the dryer.	15
“E” Variable (E1, E2, E3) service codes: Call for service.	15
Dryer Results	15
Clothes are not drying satisfactorily, drying times are too long, or load is too hot	15
Is the lint screen clogged with lint? Lint screen should be cleaned before each load.	15
Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement? Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lin...	15
Are fabric softener sheets blocking the grille? Use only one fabric softener sheet, and use it only once.	16
Is the exhaust vent the correct length? Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See the Installation Instructions.	16
Is the exhaust vent diameter the correct size? Use 4\	16
Is the dryer located in a room with temperature below 45ºF (7ºC)? Proper operation of dryer cycles requires temperatures above 45ºF (7ºC).	16
Is the dryer located in a closet? Closet doors must have ventilation openings at the top and bottom of the door. The front of the dryer requires a minimum of 1\	16
SP PN W10224594A	16

Match case Limit results 1 per page

4-wire connection: Direct wire

IMPORTANT:

A 4-wire connection

is required for mobile homes and

where local codes do not permit

the use of 3-wire connections.

Direct wire cable must have 5 ft

(1.52 m) of extra length so dryer

can be moved if needed.

Strip 5" (127 mm) of outer covering

from end of cable, leaving bare

ground wire at 5" (127 mm).

Cut 1

" (38 mm) from 3 remaining wires. Strip insulation back

1" (25 mm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the

hooked end of the wire under the screw of the terminal

block (hook facing right), squeeze hooked end together

and tighten screw, as shown.

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor

screw. Connect neutral ground wire and place the hooked end

(hook facing right) of the neutral wire (white or center wire) of direct

wire cable under the center screw of the terminal block. Squeeze

hooked ends together. Tighten screw.

A. External ground conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to

center silver-colored terminal block screw.

B. Center silver-colored terminal block screw

C. Neutral ground wire

D. Neutral wire (white or center wire)

E. ¾" (19 mm) UL listed strain relief

Connect ground wire (green or bare) of direct wire cable to

external ground conductor screw. Tighten screw.

A. External ground conductor screw

B. Ground wire (green or bare) of power supply cable

C. ¾" (19 mm) UL listed strain relief

D. Center silver-colored terminal block screw

E. Neutral ground wire

F. Neutral wire (white or center wire)

Place the hooked ends of the other direct wire cable wires under

the outer terminal block screws (hooks facing right). Squeeze

hooked ends together. Tighten screws.

Tighten strain relief screw.

Insert tab of terminal block cover into slot of dryer rear panel.

Secure cover with hold-down screw.

You have completed your electrical connection. Now go to

“Venting Requirements.”

3-wire connection: Power supply cor

Use where local co

es permit connecting ca

inet-groun

con

uctor to neutral wire.

A. 3-wire receptacle (NEMA type 10-30R)

B. 3-wire plug

C. Neutral prong

D. Spade terminals with up turned ends

E. ¾" (19 mm) UL listed strain relief

F. Ring terminals

G. Neutral (white or center wire)

Loosen or remove center silver-colored terminal block screw.

(25 mm)

(127 mm)