Whirlpool WED94HEXW Owners Manual - Page 11

5. Adjust cycle settings, if desired 7. Press and hold START/PAUSE to begin cycle Check Lint Screen Sensing Estimated Time Remaining Timed Dry Adjust Wet High Medium Low Extra Low Air Only Damp Cool Steam Static Done Wrinkle Down Reduce Shield 8 - 9 6 - 7 More Dry 4 - 5 Loud Normal Dry 2 - 3 Soft Less Dry 1 O Temperature Dryness Level Garment # Cycle Signal for auto cycles for refresh cycles Press and hold the START/PAUSE button to begin the cycle. 11-cycle model shown You may adjust different settings, depending on whether you have selected an Auto Cycle, Manual Cycle, or Steam Cycle. See the Cycle Guide for detailed information. 8. Remove garments promptly after cycle is finished NOTE: Not all options and settings are available with all cycles. Not all cycles are on all models. Auto Cycles: You can select a different dryness level, depending on your load, by pressing the button for More, Normal, or Less. Selecting More, Normal, or Less automatically adjusts the dryness level at which the dryer will shut off. Once a dryness level is set, it cannot be changed without stopping the cycle. Automatic cycles give the best drying in the shortest time. Drying time varies based on fabric type, load size, and dryness setting. Check Lint Screen Sensing Estimated Time Remaining Timed Dry Adjust Wet High Medium Low Extra Low Air Only Damp Cool Steam Static Done Wrinkle Down Reduce Shield 8 - 9 6 - 7 More Dry 4 - 5 Loud Normal Dry 2 - 3 Soft Less Dry 1 O Temperature Dryness Level Garment # Cycle Signal for auto cycles for refresh cycles 11-cycle model shown Wrinkle Shield Manual Cycles: When you select a Manual Cycle, the default time appears in the display. Use the s and t buttons to increase or decrease the time in 1 minute increments. Press and hold to change the time in 5 minute increments. The default temperature may be changed by pressing the Temperature button until the desired dry temperature is lit. Check Lint Screen Sensing Estimated Time Remaining Timed Dry Adjust Promptly remove garments after cycle Wet hDaamsp completed Cool Steam Static Down Reduce to reduce Done Wrinkle Shield wrinkling. If High Medium you will b68e-- 79unable to remove the load with Steam Low pMrooremDrpy tly,4s- 5elect tLhoued Wrinkle Shield/Wrinkle Shield with Steam Extra Low oNportmioalnDrybe2fo- 3re preSsosfting START/PAUSE. Air Only Less Dry 1 O Temperature Dryness Level Garment # Cycle Signal for auto cycles for refresh cycles Quick Refresh with Steam: Press the Garment # to select the number of garments in the load (on some models). The dryer will automatically set the drying time and temperature. For models without Garment #, the cycle time is preset to 15 minutes and is not adjustable. 6. Select any additional options Wrinkle Shield Changing the Auto Cycle settings to increase drying time If all your loads on all Auto Cycles are consistently not as dry as you would like, you may change the default settings to increase the default dryness level. Your automatic drying settings can be adjusted to adapt to different installations, environmental conditions or personal preference. This change is retained and will affect all of your Automatic cycles, not just the current cycle/load. There are 3 drying settings, which are displayed using the time display: 01 Factory preset dryness level. 02 Slightly drier clothes, 15% more drying time. 03 Much drier clothes, 30% more drying time. 11-cycle model shown with Steam Add additional options such as Static Reduce, Wrinkle Shield/ Wrinkle Shield with Steam and/or EcoBoost by pressing the button for that option. NOTE: Not all options and settings are available with all cycles. To change the drying settings: NOTE: The settings cannot be changed while the dryer is running or paused. The dryer must be in standby mode (the power button is off) to adjust the default settings. 1. Before starting a cycle, press and hold the TEMP button for 6 seconds. 2. Press the TEMP button to select the dryness level shown in the time display: 01, 02, or 03. 3. Press START/PAUSE to save the new dryness level setting. 11