Whirlpool WED9620HC Door Reversal Guide

Whirlpool WED9620HC Manual

Get Whirlpool WED9620HC PDF manuals and user guides View all Whirlpool WED9620HC manuals
Add to My Manuals
Save this manual to your list of manuals

Whirlpool WED9620HC manual content summary:

  • Whirlpool WED9620HC | Door Reversal Guide - Page 1
    the door strike to the door frame of the dryer. Rotate the strike 180° and attach to the opposite side of dryer door frame with the two screws removed earlier, as shown. Electrical Shock Hazard Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can
  • Whirlpool WED9620HC | Door Reversal Guide - Page 2
    door. 13. Reinstall door on dryer Doors with electrical wiring: Pull side of the door. 14. Reconnect wiring (doors with electrical wiring) Plug in wire. Using a Phillips screwdriver, secure the rotating assembly to the hinge with the screw removed earlier. Troubleshooting See your Owner's Manual
  • Whirlpool WED9620HC | Door Reversal Guide - Page 3
    la source de courant électrique avant l'entretien. Replacer pièces et panneaux avant de faire la mise en marche. Le non-respect de ces instructions peut causer un décès ou un choc électrique. 1. Déconnecter le câblage de la porte À l'aide d'un tournevis cruciforme, retirer la vis centrale de la
  • Whirlpool WED9620HC | Door Reversal Guide - Page 4
    la charnière sur l'autre côté Inverser l'intérieur de porte vers la gauche. À l'aide d'un tournevis T20®, réinstaller la charnière sur le côté opposé (par rapport à celui d'où il a été enlevé). 12. Réinstaller l'intérieur de porte Positionner la porte de façon à ce que l'intérieur de la porte
  • Whirlpool WED9620HC | Door Reversal Guide - Page 5
    14. Rebrancher le câblage (portes avec câblage électrique) Brancher le câblage. À l'aide d'un tournevis cruciforme, fixer l'ensemble de rotation à la charnière en utilisant la vis enlevée précédemment. Dépannage Voir le manuel d'utilisation ou consulter notre site Web et la Foire aux questions pour
  • Whirlpool WED9620HC | Door Reversal Guide - Page 6
    suave u otra superficie que no raye. 6. Retire el cierre Coloque y gire la puerta interior 180° de modo que la sección delgada quede en la parte superior y la sección gruesa en la inferior. Con un destornillador T25®, retire los cuatro tornillos que fijan la placa del pestillo en su lugar. TORX
  • Whirlpool WED9620HC | Door Reversal Guide - Page 7
    ®, vuelva a instalar la placa del pestillo en el lado opuesto desde el cual se retiró con los cuatro tornillos retirados anteriormente. 11. Gire la parte inferior del conjunto y asegúrelo en su lugar IMPORTANTE: Asegúrese de oscilar la bisagra hacia abajo frente al ensamblaje giratorio (ver paso 12
  • Whirlpool WED9620HC | Door Reversal Guide - Page 8
    el cable. Con un destornillador Phillips, fije el ensamblaje a la bisagra con el tornillo retirado anteriormente. Solución de problemas Consulte el Manual del usuario o visite nuestro sitio web y consulte la sección de "Preguntas frecuentes", para evitar posiblemente el costo de una visita de
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
1
DRYER DOOR REVERSAL INSTRUCTIONS
Round Doors with Electrical Wiring:
Tools Needed
Minimum 8" (203 mm) long TORX
®
, T20
®
, and T25
®
star drivers
#2 Phillips screwdriver
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
1. Disconnect wiring from door
Using a Phillips screwdriver, remove middle screw in hinge.
Disconnect wiring. Tuck wiring into opening.
2. Remove door from dryer
IMPORTANT:
If the protective film has not yet been removed from
the dryer, peel the film from the dryer door before proceeding.
Using a T25
®
screwdriver, remove the four screws securing the
door hinge to the dryer and lift the door up and out to remove. Place
the door on a soft towel or other non-scratch surface.
3. Move the door strike
Using a T25
®
screwdriver, remove the two screws securing the
door strike to the door frame of the dryer. Rotate the strike 180°
and attach to the opposite side of dryer door frame with the two
screws removed earlier, as shown.
4. Remove inner door from outer door
Position the door with the inside of the door facing up. Using a
Phillips screwdriver, remove the 10 screws securing the inner door
to the outer door.
5. Remove hinge
Remove cover plate to reveal hinge assembly. Then, using a T20
®
screwdriver, remove the six screws holding the hinge assembly in
place.
6. Remove latch
Flip and rotate the inner door 180° so that the thin section is at the
top and the thick section is at the bottom. Using a T25
®
screwdriver, remove the four screws securing the latch plate in
place.
TORX, T20 and T25 are trademarks of Acument Intellectual Property, LLC.