Whirlpool WEE760H0DS Installation Guide - Page 15

4. Attach terminal lugs to line 1 (black), neutral (white), and line 2 (red) wires. Loosen (do not remove) the setscrew on the front of the terminal lug and insert exposed wire end through bottom of terminal lugs. Securely tighten setscrew to torque as shown in the following Bare Wire Torque Specifications chart. A B C D E A. Terminal lug B. Setscrew C. Line 2 (red) wire D. Neutral (white) wire E. Line 1 (black) wire Bare Wire Torque Specifications Attaching terminal lugs to the terminal block - 20 lbs-in. (2.3 N-m) Wire Awg Torque 8 gauge copper 6 gauge aluminum 25 lbs-in. (2.8 N-m) 35 lbs-in. (4.0 N-m) 5. Use a hex or Phillips screwdriver to connect the bare (green) ground wire to the range with the ground-link screw and ground-link section. The ground wire must be attached over the ground-link section and must not contact any other terminal. 6. Use ³⁄₈" nut driver to connect the neutral (white) wire to the center terminal block post with one of the 10-32 hex nuts. G A B F C A. 10-32 hex nut B. Line 2 (red) C. Bare (green) ground wire D. Ground-link screw DE E. Neutral (white) wire F. Line 1 (black) G. Terminal lug 7. Connect line 2 (red) and line 1 (black) wires to the outer terminal block posts with 10-32 hex nuts. 8. Firmly tighten hex nuts. IMPORTANT: Verify the tightness of the hex nuts. 9. Replace lower access cover. Verify Anti-Tip Bracket is Installed and Engaged On Ranges Equipped with a Premium Storage Drawer: 1. Slide range into final location, making sure rear leveling leg slides into anti-tip bracket. 2. Remove the premium storage drawer. See the "Remove/ Replace Drawer" section. 3. Use a flashlight to look underneath the bottom of the range. 4. Visually check that the rear range foot is inserted into the slot of the anti-tip bracket. On Ranges Equipped with a Warming Drawer or Baking Drawer: 1. Slide range into final location, making sure rear leveling leg slides into anti-tip bracket. Leave a 1" (2.5 cm) gap between the back of the range and the back wall. 2. Place the outside of your foot against the bottom front of the warming drawer or baking drawer to keep the range from moving, and then grasp the back of the range as shown. 3. Slowly attempt to tilt the range forward. If you encounter immediate resistance, the range foot is engaged in the anti-tip bracket. Go to Step 8. 4. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, stop tilting the range and lower it gently back to the floor. The range foot is not engaged in the anti-tip bracket. IMPORTANT: If there is a snapping or popping sound when lifting the range, the range may not be fully engaged in the bracket. Check to see if there are obstructions keeping the range from sliding to the wall or keeping the range foot from sliding into the bracket. Verify that the bracket is held securely in place by the mounting screws. 5. Slide the range forward, and verify that the anti-tip bracket is securely attached to the floor or wall. 6. Slide range back so the rear range foot is inserted into the slot of the anti-tip bracket. 7. Repeat steps 1 and 2 to ensure that the range foot is engaged in the anti-tip bracket. If the rear of the range lifts more than ½" (1.3 cm) off the floor without resistance, the anti-tip bracket may not be installed correctly. Do not operate the range without anti-tip bracket installed and engaged. Please reference the "Warranty" section of the User Guide to contact service. 8. Move the range into its final location. Check that the range is level by placing a level on the oven bottom. See the "Level Range" section. IMPORTANT: If the range is moved to adjust the leveling legs, verify that the anti-tip bracket is engaged by repeating steps 1 to 8. 15