Whirlpool WFG710H0AH Installation Guide - Page 16

To Convert Oven Bake Burner Natural Gas to LP Gas, To Convert Oven Broil Burner Natural Gas to LP

Get Whirlpool WFG710H0AH PDF manuals and user guides View all Whirlpool WFG710H0AH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

To Convert Oven Bake Burner (Natural Gas to LP Gas) 1. Remove the oven racks. 2. Remove 2 screws at the rear of the oven bottom. 3. Lift the rear of the oven bottom up and back until the front of the panel is away from the front frame. Remove from oven and set it aside on a covered surface. A B 8. Position the back of the bake burner over the oven orifice, and slide the tab on front of the bake burner into the front of the oven. 9. Reattach the bake burner with 1 screw. 10. Position the front of the oven bottom panel toward the front frame and lower the rear of the oven bottom panel into the oven. 11. Reattach the oven bottom panel with screws. To Convert Oven Broil Burner (Natural Gas to LP Gas) 1. Remove the screw from the broil burner. 2. Remove the broil burner from the broil burner orifice hood. NOTE: The broil burner will hang in the back of the oven while changing the orifice hood. A. Screws B. Oven bottom 4. Remove 1 screw from the bake burner. 5. Slide the front of the bake burner to the side to remove tab from front of oven. Lift the back of the bake burner off the oven orifice, and set the bake burner aside. B A A. Screw B. Bake burner 6. Use a ³⁄₈" nut driver or combination wrench and turn the Natural gas bake burner orifice spud counterclockwise to remove. The spud will be stamped with a "47." 7. Replace the "47" spud with a "56" spud. Install the LP gas bake burner orifice spud, turning it clockwise until snug. IMPORTANT: Do not overtighten. A B A C A. Broil burner B. Screws C. Orifice hood 3. Use a ³⁄₈" combination wrench and turn the Natural gas broil burner orifice hood counterclockwise to remove. The hood will be stamped with a "155." 4. Replace the "155" hood with a "100" hood. Install the LP gas broiler burner orifice hood, turning it clockwise until snug. IMPORTANT: Do not overtighten. A x.xx A. Orifice spud 16 A. Orifice hood 5. Place the broil burner on the broil burner orifice hood and insert the broil burner ceramic igniter in the hole in the rear of the oven. 6. Position the broil burner against the top of the oven and attach it with 2 screws. 7. Replace storage drawer or warming drawer. See the "Storage Drawer" or "Warming Drawer or Premium Storage Drawer" section. 8. Replace the oven door if it has been removed. See the "Oven Door" section. 9. Replace the oven racks.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
16
To Convert Oven Bake Burner (Natural Gas to LP Gas)
1.
Remove the oven racks.
2.
Remove 2 screws at the rear of the oven bottom.
3.
Lift the rear of the oven bottom up and back until the front of
the panel is away from the front frame. Remove from oven
and set it aside on a covered surface.
4.
Remove 1 screw from the bake burner.
5.
Slide the front of the bake burner to the side to remove tab
from front of oven. Lift the back of the bake burner off the
oven orifice, and set the bake burner aside.
6.
Use a
³⁄₈
" nut driver or combination wrench and turn the
Natural gas bake burner orifice spud counterclockwise to
remove. The spud will be stamped with a “47.”
7.
Replace the “47” spud with a “56” spud. Install the LP gas
bake burner orifice spud, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
8.
Position the back of the bake burner over the oven orifice,
and slide the tab on front of the bake burner into the front of
the oven.
9.
Reattach the bake burner with 1 screw.
10.
Position the front of the oven bottom panel toward the front
frame and lower the rear of the oven bottom panel into the
oven.
11.
Reattach the oven bottom panel with screws.
To Convert Oven Broil Burner (Natural Gas to LP Gas)
1.
Remove the screw from the broil burner.
2.
Remove the broil burner from the broil burner orifice hood.
NOTE:
The broil burner will hang in the back of the oven while
changing the orifice hood.
3.
Use a
³⁄₈
" combination wrench and turn the Natural gas broil
burner orifice hood counterclockwise to remove. The hood
will be stamped with a “155.”
4.
Replace the “155” hood with a “100” hood. Install the LP gas
broiler burner orifice hood, turning it clockwise until snug.
IMPORTANT:
Do not overtighten.
5.
Place the broil burner on the broil burner orifice hood and
insert the broil burner ceramic igniter in the hole in the rear of
the oven.
6.
Position the broil burner against the top of the oven and
attach it with 2 screws.
7.
Replace storage drawer or warming drawer. See the “Storage
Drawer” or “Warming Drawer or Premium Storage Drawer”
section.
8.
Replace the oven door if it has been removed. See the “Oven
Door” section.
9.
Replace the oven racks.
A. Screws
B. Oven bottom
A. Screw
B. Bake burner
A. Orifice spud
A
B
A
B
A
A. Broil burner
B. Screws
C. Orifice hood
A. Orifice hood
B
C
A
x.xx
A