Whirlpool WFW5620HW Owners Manual - Page 35
Cycle Modifiers, Utility Cycles, Cycle Options - lowes
View all Whirlpool WFW5620HW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 35 highlights
Washing During the wash cycle, this will display to let you know the cycle is in progress. PreSoak This symbol will be displayed to let you know a presoak is in progress. Detergent Low (on some models) When detergent in the bulk dispenser is running low, the display will show the detergent level (Low). Add Garment When "Add Garment" is displayed, you may pause the washer, open the door, and add items. Touch and hold START/PAUSE to start the washer again. 6 UTILITY CYCLES Clean Washer Use this every 30 washes to keep the inside of your washer fresh and clean. This cycle uses a higher water level. Use with affresh Washer Cleaner tablets or liquid chlorine bleach to thoroughly clean the inside of your washer. When using this cycle, the drum should be empty. This cycle should not be interrupted. See the "Washer Care" section. Drain & Spin This cycle removes excess water from the load or special-care items washed by hand. Use this cycle after a power failure. For some fabrics, you may choose to set a slower spin speed. Door Locked 7 CYCLE OPTIONS The Door Locked symbol will display to indicate that the door is locked and cannot be opened without first pausing or canceling the cycle. You may add or remove options for each cycle. Not all options can be used with all cycles, and some are preset to work with certain cycles. Options vary by model. Control Lock When the Contol Lock symbol is displayed, the buttons are disabled. Touch and hold EXTRA RINSE for 3 seconds to enable the buttons. Steam Clean (on some models) The Steam Clean option adds additional soak and wash time to many cycles to help remove tough stains, as well as a steam boost for added cleaning power. TumbleFresh (on some models) hold 3 sec for This symbol will be displayed when the TumbleFresh option is activated. The load will Cycle Signal hoAldn i3ntsegercatfeodrheatheor hldelp3s stoecmafoinrtain ohpotlimda3l wsaesch for CottehnmetrSpoetelraaLtmuorcCeksle. aSneeop"tCiFoyanc.nleFGreusidhe" for cyclePs rtheaSt oaallokw tumble periodically for up to 12 hours. You can also touch and hold STEAM CLEAN FanFresh (on some models) for 3 seconds to turn cycle signals on or off. This symbol will be displayed when the FanFresh option is activated. The fan will turn on and the load will tumble periodically for up to 12 hours. Extra Rinse Activate this option to add an extra rinse to most cycles. End Once the cycle is complete, "End" will display. Remove the load promptly for best results. You can also touch and hold EXTRA RINSE for 3 seconds to disable/enable the Control Lock. Load & Go (on some models) 5 CYCLE MODIFIERS When you select a cycle, its default settings will light up. Touch to adjust cycle modifiers on the washer before touching START/PAUSE. Additional wash modifiers or options selected after touching Start/Pause may not activate. Once a wash setting is selected, it is saved for the cycle selected. To return to factory default cycle settings, unplug washer for 30 seconds; then plug back in. See "Cycle Guide" for default cycle settings. Touch to select this option If you want to automatically add HE detergent to the wash load at the proper time. IMPORTANT: When using the dispenser cartridge with concentrated liquid detergent, be sure to change the detergent concentration settings in the control if the detergent used is different than factory preset of 2x concentration. Change the detergent concentration setting by touching and holding TEMP and SOIL for 3 seconds. NOTE: Some modifiers may increase or decrease the estimated time remaining. You can also touch and hold LOAD & GO for 3 seconds to set a presoak. Temp The recommended wash temperature is preset for each cycle. Some preset temperatures can be changed. You may select a different wash temperature based on the level of soil and type of fabric being washed. For best results, use the warmest wash water safe for your fabric, following the garment label instructions. All wash temperatures feature a cold rinse. PreSoak (on some models) Touch to add a presoak time of your choice to a wash cycle. Spin The recommended spin speed is preset for each cycle. Some preset speeds can be changed. ■■ Faster spin speeds mean shorter dry times, but may increase wrinkling in your load. ■■ Slower spin speeds reduce wrinkling, but will leave your load more damp. Soil The recommended soil level is preset for each cycle. Some preset soil levels can be changed. For heavily soiled and sturdy fabrics, select the Heavy Soil Level setting. For lightly soiled and delicate fabrics, select the Light Soil Level setting. Lower soil level settings will help reduce tangling and wrinkling. hold 3 sec for Cycle Signal 35