Home » Whirlpool Manuals » Laundry Washers » Whirlpool WFW8400TW » Manual Viewer

Whirlpool WFW8400TW Use and Care Guide - Page 10

Level the Washer, Complete Installation - won t start

UPC - 883049065304

View all Whirlpool WFW8400TW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Level the Washer Properly leveling your washer avoids excessive noise and vibration. NOTE: Installing washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended. 1. Slide the washer to its final location. 2. Check that all four feet are in firm contact with the floor. 3. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side then front to back. Complete Installation 1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See "Electrical Requirements." 2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 3. Check that you have all of your tools. 4. Dispose of/recycle all packaging materials. 5. Check that the water faucets are on. 6. Check for leaks around faucets and inlet hoses. WARNING If the washer is against a wall, move the washer out slightly before tipping back. If the washer is not level, first prop the front with a wooden block and adjust the front feet height moving the hexagonal plastic part as necessary. Repeat to adjust back feet. 4. Make sure all four feet are stable and resting on the floor. Then check that the washer is perfectly level (use a level). Repeat steps 1-3 until washer is level. 5. After the washer is level, and all four feet are in firm contact with the floor, use a 9/16" (14 mm) open-end wrench to turn the locknuts on the feet, tightly against the washer cabinet. IMPORTANT: All four feet must be tightened. If the locknuts are not tight against the washer cabinet, the washer may vibrate. 6. The washer should not move front to back, side to side, or diagonally when pushed on its top edges. 7. Confirm the levelness of the washer. Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 7. Plug into a grounded 3 prong outlet. 8. Read "Washer Use." 9. To test and to clean your machine, make sure that there are no clothes in the washer and add one AFFRESH™ tablet to the washer drum. Select POWER, the CLEAN WASHER cycle and then select START. This cycle will take approximately 50 minutes to complete. Allow the washer to complete the entire cycle without interruption. 10

Section	Page
front-loading Automatic washer	1
Use & Care Guide	1
For questions about features, operation/performance, parts, accessories, or service call: 1-800-253-1301	1
In Canada, call: 1-800-807-6777	1
or visit our website at www.whirlpool.com or www.whirlpool.ca	1
Laveuse automatique À chargement frontal	1
Guide d’utilisation et d’entretien	1
Au Canada, pour assistance, installation ou service, composez le : 1-800-807-6777	1
ou visitez notre site internet à www.whirlpool.ca	1
Table of Contents/Table des matières 2	1
Table of Contents	2
TABLE DEs MATIÈRES	2
WASHer Safety	3
INSTALLATION requirements	4
Tools and Parts	4
Tools needed for connecting the water inlet hoses	4
Tools needed for installation	4
Alternate Parts	4
Options	4
Pedestal	4
Optional pedestal	4
Stack Kit	4
Location Requirements	4
Installation clearances	5
Washer Dimensions	5
Recommended installation spacing for custom undercounter installation	5
Recommended installation spacing for recessed or closet installation, with or without a pedestal	5
Recommended installation spacing for recessed or closet installation, with stacked washer and dryer	6
Recommended installation spacing for cabinet installation	6
Drain System	6
Standpipe drain system - wall or floor (views A & B)	6
Laundry tub drain system (view C)	6
Floor drain system (view D)	6
Electrical Requirements	7
installation instructions	8
Remove Transport System	8
1. On the back of the washer, loosen the 4 transport bolts using a 13 mm wrench.	8
2. Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.	8
3. Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.	8
4. Cover the bolt holes with the 4 transport bolt hole plugs.	8
Connect the Inlet Hoses	8
Connect the inlet hoses to the water faucets	8
1. Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.	8
2. Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.	8
3. Using pliers, tighten the couplings with an additional two-thirds turn.	8
Clear the water lines	8
Connect the inlet hoses to the washer	9
1. Attach the hot water hose to the washer’s hot (H) water inlet valve. Screw on coupling by hand until it is seated on the washer.	9
2. Attach the cold water hose to the washer’s cold (C) water faucet. Screw on coupling by hand until it is seated on the washer.	9
3. Using pliers, tighten the couplings with an additional two-thirds turn.	9
4. Turn on the water faucets completely and check for leaks.	9
Route the Drain Hose	9
Floor drain	9
Secure the Drain Hose	9
1. Drape the power cord over the washer top.	9
2. Move the washer to its final location.	9
3. Place the drain hose in the laundry tub or standpipe as shown. See illustrations A and B.	9
4. If the washer faucets and the drain standpipe are recessed, put the hooked end of the drain hose in the standpipe as shown. See illustration C.	9
Level the Washer	10
1. Slide the washer to its final location.	10
2. Check that all four feet are in firm contact with the floor.	10
3. Check the levelness of the washer by placing a level on the top edge of the washer, first side to side then front to back.	10
4. Make sure all four feet are stable and resting on the floor. Then check that the washer is perfectly level (use a level). Repeat steps 1-3 until washer is level.	10
5. After the washer is level, and all four feet are in firm contact with the floor, use a 9/16\	10
6. The washer should not move front to back, side to side, or diagonally when pushed on its top edges.	10
7. Confirm the levelness of the washer.	10
Complete Installation	10
1. Check the electrical requirements. Be sure that you have the correct electrical supply and the recommended grounding method. See “Electrical Requirements.”	10
2. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.	10
3. Check that you have all of your tools.	10
4. Dispose of/recycle all packaging materials.	10
5. Check that the water faucets are on.	10
6. Check for leaks around faucets and inlet hoses.	10
7. Plug into a grounded 3 prong outlet.	10
8. Read “Washer Use.”	10
9. To test and to clean your machine, make sure that there are no clothes in the washer and add one AFFRESH™ tablet to the washer drum. Select POWER, the CLEAN WASHER cycle and then select START. This cycle will take approximately 50 minutes to com...	10
FEATURES AND BENEFITS	11
Electronic Controls	11
Auto Water Level	11
Larger Load Size	11
Suspension System	11
Stainless Steel Drum	11
Adaptive Variable Speed Motor	11
Spin Speeds	11
Heating Element	11
Add A Garment	11
Dynamic Balance	11
Smart Dispensers	11
Use only HE High Efficiency detergent.	11
washer USE	12
Starting Your Washer	12
Using the Proper Detergent	12
Use only HE High Efficiency detergent.	12
First Wash Cycle Without Laundry	12
For All Wash Cycles	12
1. To load washer Open the washer door by pulling on the handle. Sort laundry according to color and type of fabric. Place a load of sorted clothes in the washer. Do not overload washer. Overloading can cause poor cleaning.	12
2. Close the washer door by pushing it firmly until the lock clicks. The washer door will remain locked during the wash cycle.	12
3. Open the dispenser drawer and add laundry products to the detergent, bleach, or fabric softener compartments. Close drawer slowly to avoid spills. See “Using the Dispenser.”	12
4. Turn on the washer by selecting POWER. Select one of the cycles by turning the cycle selector. The indicator light for the selected cycle will illuminate. When selecting a Wash Cycle, the preset Modifiers and Options, Water Temp, and Spin Speed fo...	12
5. Select the desired OPTIONS. Not all Options are available with all cycles. See “Options.”	12
6. If desired, select the END OF CYCLE SIGNAL. The signal is helpful when you are washing items that should be removed from the washer as soon as it stops. Press END OF CYCLE SIGNAL to select ON or OFF.	12
7. To begin the wash cycle immediately Select and hold START (for approximately 1 second).	13
8. To begin the wash cycle later Select DELAY WASH until the desired delay time (in hours) is displayed. Select START. The countdown to the wash cycle will show in the display window.	13
Using the Dispenser	13
Choosing the Right Detergent	13
Use only HE High Efficiency detergent.	13
To fill dispenser compartments	13
1. Pull out the dispenser drawer.	13
2. Add the desired laundry products to the proper compartment.	13
3. Push in the dispenser drawer slowly and completely (to avoid a spill).	13
Dispenser	13
Main Wash detergent compartment	13
Chlorine bleach compartment	13
Fabric softener compartment	13
Pausing or Restarting	13
1. To pause the washer at any time, select PAUSE/CANCEL.	13
2. To continue the cycle, select and hold START (for approximately 1 second).	13
Changing Cycles and Options	14
To stop a cycle and select a new cycle	14
1. Select PAUSE/CANCEL once.	14
2. Select desired cycle.	14
3. Select the desired OPTIONS.	14
4. Select and hold START (for approximately 1 second) to restart the washer at the beginning of the new cycle.	14
To cancel a cycle	14
1. Select PAUSE/CANCEL twice.	14
2. The washer powers down, the door unlocks, and clothes can be removed.	14
To change Options after the cycle has started	14
1. Select PAUSE/CANCEL once.	14
2. Select the desired OPTIONS. If the option is not available, the machine will beep.	14
3. Select and hold START (for approximately 1 second) to continue the cycle.	14
To drain the washer manually	14
1. Select PAUSE/CANCEL.	14
2. Select DRAIN/SPIN.	14
3. Select and hold START (for approximately 1 second) to begin the drain.	14
4. When the spin is complete, the door unlocks. Items can be removed from the washer.	14
Status Lights	14
Adding items	14
1. Select PAUSE/CANCEL. The washer door unlocks, and items can be added.	14
2. To continue the cycle, close the door and select and hold START (for approximately 1 second).	14
Cycle Complete	14
Locking controls	14
Estimated Time Remaining	14
Door Locked	14
Cycles	14
Wash Cycles	14
Preset Cycle Settings	15
Cycle	15
Estimated Time* (hr:min)	15
Wash Temp	15
Spin Speed	15
Sanitary	15
Whitest Whites	15
Heavy Duty	15
Normal/Casual	15
Quick Wash	15
Delicate/Hand Wash	15
Clean Washer	15
Rinse/Spin	15
Drain/Spin	15
Soak	15
Normal Sounds	16
Options and Modifiers	16
Delay Wash	16
Extra Rinse	16
Prewash	16
Wash Temp	16
Temperature Guide	16
Auto Temp Control	16
SPIN SPEED	16
End of Cycle Signal	16
Laundry Guide	17
Refer to this chart for suggested load types and their corresponding cycles. Listed to the right are the options available to each of these washer cycles.	17
Available Options	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
4	17
Laundry Tips	18
Preparing clothes for washing	18
Use only HE High Efficiency detergent.	18
Sorting	18
Unloading	18
Loading	18
Loading suggestions	18
Stain Removal Guide	19
Ink	19
4	19
Grass	19
4	19
Blood	19
4	19
Tomato Products	19
4	19
Coffee/ Chocolate	19
4	19
Mud	19
4	19
Cosmetics	19
Dirty Motor Oil	19
Ring around the Collar	19
4	19
Washer care	20
Cleaning Your Washer	20
Cleaning the Door Seal/Bellow	20
1. Open the washer door and remove any clothing or items from the washer.	20
2. Inspect the colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/bellow to inspect all areas under the seal/bellow and to check for foreign objects.	20
3. If stained areas are found, wipe down these areas of the seal/ bellow, using the procedure that follows.	20
a) Mix a dilute solution, using ¾ cup (177 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water.	20
b) Wipe the seal/bellow area with the dilute solution, using a damp cloth.	20
c) Let stand 5 minutes.	20
d) Wipe down area thoroughly with a dry cloth and let the washer interior air dry with door open.	20
Washer Maintenance Procedure	20
Begin procedure	20
1. Open the washer door and remove any clothing or items from the washer.	20
2. Using the AFFRESH™ washer cleaner (Recommended): Add one AFFRESH™ washer cleaner tablet to the washer drum.	20
3. Open the dispenser drawer and immediately add 2/3 cup (160 mL) of liquid chlorine bleach to the bleach compartment.	20
4. Close the washer door and dispenser drawer.	20
5. Select the CLEAN WASHER cycle.	20
6. Press START.	20
7. The cycle will determine whether clothing or other items are in the washer.	20
8. Once the cycle has begun, allow the cycle to complete.	20
9. After the cycle is complete, leave the door open slightly, to allow for better ventilation and drying of washer interior.	20
Always do the following to maintain washer freshness	20
Cleaning the exterior	20
Cleaning the dispenser drawer	20
1. Unlock the dispenser drawer by pressing the Release Lever. See “Using the Dispenser.” Remove the drawer.	20
2. Remove the inserts (the siphon from the softener and bleach compartments).	20
3. Wash the parts under running water.	20
4. Replace the inserts and return the dispenser to the drawer.	20
Water Inlet Hoses	21
Vacation, Storage, and Moving Care	21
Non-use or vacation care:	21
To winterize washer:	21
1. Put 1 qt (1 L) of R.V.-type antifreeze in the drum.	21
2. Run washer on a Drain/Spin cycle.	21
3. Unplug washer or disconnect power.	21
4. Shut off both water faucets.	21
5. Disconnect water inlet hoses from faucets and drain.	21
To use washer again:	21
1. Flush water pipes.	21
2. Reconnect water inlet hoses to faucets.	21
3. Turn on both water faucets.	21
4. Plug in washer or reconnect power.	21
5. Run the washer through the Normal/Casual cycle with ½ the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	21
To transport the washer:	21
1. If washer will be moved during freezing weather, put in 1 qt (1 L) of R.V.-type antifreeze in the drum. Run washer on a Drain/Spin cycle.	21
2. Unplug the power cord.	21
3. Disconnect the drain hose from the drain system and attach to rear panel clips.	21
4. Shut off both water faucets.	21
5. Disconnect the water inlet hoses from faucets, then drain the hoses and clip them to the rear panel of the washer.	21
6. IMPORTANT: Call service. Do not reuse transport bolts. Washer must be transported in the upright position. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.	21
Reinstalling the washer	21
1. Follow the “Installation Instructions” to locate, level and connect the washer.	21
2. Run the washer through the Normal/Casual cycle with ½ the manufacturer’s recommended amount of HE detergent for a medium-size load, to clean the washer and remove the antifreeze, if used.	21
troubleshooting	22
First try the solutions suggested here or visit our website and reference FAQs (Frequenly Asked Questions) to possibly avoid the cost of a service call...	22
In U.S.A. www.whirlpool.com/help In Canada www.whirlpool.ca	22
Washer and Components	22
Error codes	22
Noisy, vibrating, off-balance	22
Leaking	22
Dispenser operation	23
Washer odor	23
Door won't unlock	23
Washer Operation	23
Washer won't power up	23
Washer cycle won’t start	23
Control won’t accept selections or won’t shut off	23
Washer stops working	24
When the washer stops working At the beginning of the cycle:	24
Washer won’t dispense	24
Washer won’t fill	24
Washer won’t run	24
Incorrect water temperature or Wash/Rinse temperature	24
Not enough water/Not enough suds	24
When the washer stops working At the middle of the cycle:	24
Washer continues to fill or drain, cycle seems stuck	24
Washer won’t drain or spin, water remains in washer	24
Washer motor overheats	24
Noise, Vibration, & Time	24
Washer vibrates	24
Cycle time changes/Cycle too long	25
Clothes Care	25
Load too wet	25
Residue, lint, stains on load; gray whites, dingy colors	25
Load is wrinkled, twisted, tangled	25
Assistance or Service	26
If you need replacement parts	26
In the U.S.A.	26
For further assistance	26
In Canada	26
For further assistance	26
WHIRLPOOL CORPORATION LAUNDRY WARRANTY	27
For one year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Whirlpool Corporation or Whirlpool Canada LP (hereafter “Whirlpool”) will pay for Fa...	27
2. Service calls to correct the installation of your major appliance, to instruct you on how to use your major appliance, to replace or repair house fuses, or to correct house wiring or plumbing.	27
3. Service calls to repair or replace appliance light bulbs, air filters or water filters. Consumable parts are excluded from warranty coverage.	27
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in accordance with electrical or plumbing codes, or use of products not approved by Whirlpool.	27
5. Cosmetic damage, including scratches, dents, chips or other damage to the finish of your major appliance, unless such damage results from defects in materials or workmanship and is reported to Whirlpool within 30 days from the date of purchase.	27
6. Pick up and delivery. This major appliance is intended to be repaired in your home.	27
7. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.	27
8. Expenses for travel and transportation for product service if your major appliance is located in a remote area where service by an authorized Whirlpool servicer is not available.	27
9. The removal and reinstallation of your major appliance if it is installed in an inaccessible location or is not installed in accordance with Whirlpool’s published installation instructions.	27
10. Replacement parts or repair labor on major appliances with original model/serial numbers that have been removed, altered, or cannot be easily determined.	27
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow limitations on the du...	27
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. WHIRLPOOL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation of incide...	27
If outside the 50 United States and Canada, contact your authorized Whirlpool dealer to determine if another warranty applies.	27
If you think you need repair service, first see the “Troubleshooting” section of the Use & Care Guide. If you are unable to resolve the problem after checking “Troubleshooting,” additional help can be found by checking the “Assistance or Se...	27
SÉCURITÉ DE LA LAVEUSE	28
Exigences d'installation	29
Outillage et pièces	29
Outils nécessaires au raccordement des tuyaux d'arrivée d'eau	29
Outils nécessaires à l'installation	29
Autres pièces	29
Options	29
Piédestal	29
Piédestal facultatif	29
Ensemble de superposition	29
Exigences d'emplacement	29
Dégagements de séparation à respecter	30
Dimensions de la laveuse	30
Espacement recommandé pour une installation personnalisée sous un comptoir	30
Espacement recommandé pour une installation dans un encastrement ou dans un placard, avec ou sans piédestal	30
Espacement recommandé pour une installation dans un encastrement ou dans un placard, avec laveuse et sécheuse superposées	31
Espacement recommandé pour l’installation dans un placard	31
Système de vidange	31
Système de vidange avec tuyau de rejet à l'égout - mural ou au plancher (vues A et B)	31
Système de vidange avec évier de buanderie (vue C)	31
Système de vidange au plancher (vue D)	31
Spécifications électriques	32
Instructions d'installation	33
Élimination des accessoires de transport	33
1. Au moyen d'une clé de 13 mm, desserrer les 4 boulons de transport.	33
2. Une fois le boulon desserré, le déplacer au centre du trou et retirer complètement le boulon, y compris la cale d'espacement en plastique couvrant le boulon.	33
3. Une fois que les 4 boulons ont été retirés, jeter les boulons et les cales d'espacement. Puis tirer le cordon d'alimentation à travers l'ouverture du panneau arrière et obturer le trou avec le bouchon fourni.	33
4. Couvrir les trous des boulons avec les 4 bouchons pour les trous des boulons de transport.	33
Raccordement des tuyaux d'alimentation	33
Connecter les tuyaux d'alimentation aux robinets d'eau	33
1. Fixer un tuyau au robinet d'eau chaude. Visser complètement le raccord à la main pour qu'il comprime la rondelle.	33
2. Fixer un tuyau au robinet d'eau froide. Visser complètement le raccord à la main pour qu'il comprime la rondelle.	33
3. À l'aide d'une pince, serrer les raccords en effectuant deux tiers de tour supplémentaires.	33
Purger les canalisations d'eau	33
Connecter les tuyaux d’alimentation à la laveuse	34
1. Fixer le tuyau d’eau chaude au robinet du tuyau d’alimentation d’eau chaude (H) de la laveuse. Visser le raccord à la main pour qu'il comprime la rondelle.	34
2. Fixer le tuyau d’eau froide au robinet d'eau froide (C) de la laveuse. Visser le raccord à la main pour qu'il comprime la rondelle.	34
3. À l’aide d’une pince, serrer les raccords en effectuant deux tiers de tour supplémentaires.	34
4. Ouvrir les robinets d'eau complètement et vérifier s’il y a des fuites.	34
Acheminement du tuyau de vidange	34
Égout au plancher	34
Immobilisation du tuyau de vidange	35
1. Faire passer le cordon d'alimentation par-dessus la laveuse.	35
2. Déplacer la laveuse à son emplacement final.	35
3. Placer le tuyau de vidange dans l'évier de buanderie ou le tuyau de rejet à l'égout. Voir les illustrations A et B.	35
4. Si les robinets d'eau et le tuyau rigide de rejet à l'égout sont placés en retrait, introduire l'extrémité en crochet du tuyau de vidange dans le tuyau rigide de rejet à l'égout. Voir l'illustration C.	35
Réglage de l’aplomb de la laveuse	35
1. Faire glisser la laveuse à son emplacement final.	35
2. S’assurer que les quatre pieds sont bien en contact avec le plancher.	35
3. Utiliser un niveau placé sur le bord supérieur de la laveuse pour contrôler l’aplomb, d'abord transversalement, puis dans le sens avant arrière.	35
4. Vérifier que les quatre pieds sont stables et reposent sur le plancher. Vérifier ensuite que la laveuse est parfaitement d’aplomb (utiliser un niveau). Répéter les étapes 1 à 3 jusqu’à ce que la laveuse soit d’aplomb.	35
5. Après que l’aplomb de la laveuse a été établi et que les quatre pieds sont bien en contact avec le plancher, tourner les écrous de blocage sur les pieds à l’aide d'une clé à molette de 9/16\	35
6. La laveuse ne doit pas bouger d’avant en arrière, latéralement ou transversalement lorsqu’on appuie sur les bords supérieurs.	35
7. Vérifier le bon aplomb de la laveuse.	35
Achever l’installation	35
1. Consulter les spécifications électriques. Vérifier que la tension électrique disponible est correcte et que la prise de courant est convenablement reliée à la terre. Voir “Spécifications électriques”.	35
2. Vérifier que toutes les pièces sont maintenant installées. S'il reste une pièce, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée.	35
3. S'assurer d'avoir récupéré tous vos outils.	35
4. Jeter ou recycler tous les matériaux d'emballage.	35
5. Vérifier que chaque robinet d'arrivée d'eau est ouvert.	35
6. Vérifier s'il y a des fuites autour des robinets et des tuyaux d'arrivée d'eau.	35
7. Brancher sur une prise à 3 alvéoles reliée à la terre.	35
8. Lire “Utilisation de la laveuse”.	35
9. Pour tester le fonctionnement de la machine et la nettoyer, s'assurer qu'il n'y a pas de vêtements dans la laveuse, puis ajouter une tablette AFFRESH™ dans le tambour de la laveuse. Sélectionner POWER (mise sous tension), le programme CLEAN WA...	35
CARACTÉRISTIQUES ET AVANTAGES	36
Commandes électroniques	36
Niveau d’eau automatique	36
Volume de charge plus important	36
Système de suspension	36
Tambour en acier inoxydable	36
Moteur adaptatif à vitesse variable	36
Vitesses d’essorage	36
Élément de chauffage	36
Add A Garment (ajouter un vêtement)	36
Équilibre dynamique	36
Distributeurs intelligents	36
Utiliser uniquement un détergent HE Haute efficacité.	36
UTILISATION DE LA LAVEUSE	37
Mise en marche de la laveuse	37
Utilisation du détergent approprié	37
Utiliser uniquement un détergent HE Haute efficacité.	37
Premier programme de lavage sans linge à laver	37
Pour tous les programmes de lavage	37
1. Pour charger la laveuse Ouvrir la porte de la laveuse en tirant sur la poignée. Trier le linge d’après la couleur et le type de tissu. Placer une charge de linge trié dans la laveuse. Ne pas surcharger la laveuse. Une surcharge peut causer un...	37
2. Fermer la porte de la laveuse en la poussant fermement jusqu’à ce que le verrou s’enclenche. La porte de la laveuse demeurera verrouillée durant le programme de lavage.	38
3. Ouvrir le tiroir distributeur et verser les produits de lessive dans les compartiments de détergent, d'agent de blanchiment ou d'assouplissant de tissu. Fermer le tiroir lentement pour éviter les renversements. Voir “Utilisation du distributeu...	38
4. Mettre la laveuse en marche en sélectionnant POWER (alimentation). Sélectionner un des programmes en tournant le sélecteur de programme. Le témoin lumineux correspondant au programme sélectionné s'allumera. Lors de la sélection d'un program...	38
5. Sélectionner les options désirées. Toutes les options ne sont pas disponibles avec tous les programmes. Voir “Options”.	38
6. Si désiré, sélectionner le signal de fin de programme. Le signal est utile lorsque vous lavez des articles qui doivent être enlevés de la laveuse aussitôt qu'elle s'arrête. Appuyer sur END OF CYCLE SIGNAL (signal de fin de programme) pour s...	38
7. Pour commencer le programme de lavage immédiatement Sélectionner START (pendant 1 seconde environ).	38
8. Pour commencer le programme de lavage ultérieurement Sélectionner DELAY WASH (lavage différé) jusqu'à ce que la durée de délai souhaitée (en heures) s'affiche. Sélectionner START (mise en marche). La fenêtre d'affichage indique le compte...	38
Utilisation du distributeur	38
Choix du détergent approprié	38
Utiliser uniquement un détergent HE Haute efficacité.	38
Pour remplir les compartiments du distributeur	38
1. Tirer le tiroir distributeur.	38
2. Ajouter les produits de lessive désirés dans le compartiment approprié.	38
3. Repousser le tiroir distributeur lentement et complètement (pour éviter les renversements).	38
Distributeur	38
Compartiment pour détergent du lavage principal	38
Compartiment de l'agent de blanchiment	39
Compartiment pour assouplissant de tissu	39
Pause ou remise en marche	39
1. Pour mettre la laveuse en pause à tout moment, sélectionner PAUSE/CANCEL (pause/annulation).	39
2. Pour poursuivre le programme, sélectionner START (pendant environ 1 seconde).	39
Modification des programmes et options	39
Pour arrêter un programme et en sélectionner un autre	39
1. Sélectionner une fois PAUSE/CANCEL (pause/annulation).	39
2. Sélectionner le programme désiré.	39
3. Sélectionner les OPTIONS désirées.	39
4. Sélectionner START (pendant environ 1 seconde) pour remettre la laveuse en marche au début du nouveau programme.	39
Pour annuler un programme	39
1. Sélectionner deux fois PAUSE/CANCEL (pause/annulation).	39
2. La laveuse s'éteint, la porte se déverrouille et les vêtements peuvent être retirés.	39
Pour modifier les options lorsque le programme a commencé	39
1. Sélectionner une fois PAUSE/CANCEL (pause/annulation).	39
2. Sélectionner les OPTIONS désirées. Si l'option n'est pas disponible, la machine émet un bip.	39
3. Sélectionner START (pendant environ 1 seconde) pour poursuivre le programme.	39
Pour vidanger la laveuse manuellement	39
1. Sélectionner PAUSE/CANCEL (pause/annulation).	39
2. Sélectionner DRAIN/SPIN (vidange/essorage).	39
3. Sélectionner START (pendant environ 1 seconde) pour commencer la vidange.	39
4. Lorsque l'essorage est terminé, la porte se déverrouille. Les articles peuvent être retirés de la laveuse.	39
Témoins lumineux	39
Ajout d'articles	39
1. Sélectionner PAUSE/CANCEL (pause/annulation). La porte de la laveuse se déverrouille et les articles peuvent être ajoutés.	39
2. Pour poursuivre le programme, fermer la porte et sélectionner START (pendant environ 1 seconde).	39
Cycle Complete (programme terminé)	39
Verrouillage des commandes	39
Durée résiduelle estimée	40
Door Locked (porte verrouillée)	40
Programmes	40
Programmes de lavage	40
Préréglages de programme	40
Programme	40
Durée estimée* (hr:min)	40
Wash Temp (température de lavage)	40
Spin Speed (vitesse d'essorage))	40
Sanitary (sanitaire)	41
Whitest Whites (blancs les plus blancs)	41
Heavy Duty (service intense)	41
Normal/Casual (normal/tout-aller)	41
Quick Wash (lavage rapide)	41
Delicate/Hand Wash (articles délicats/lavage à la main)	41
Clean Washer (nettoyage de la laveuse)	41
Rinse/Spin (rinçage/essorage)	41
Drain/Spin (vidange/essorage)	41
Soak (trempage)	41
Sons normaux	41
Options et modificateurs	42
Delay Wash (lavage différé)	42
Extra Rinse (rinçage supplémentaire)	42
Prewash (prélavage)	42
Wash Temp (température de lavage)	42
Guide de température	42
Commande automatique de la température	42
SPIN SPEED (vitesse d'essorage)	42
Signal de fin de programme	42
Guide de lessivage	43
Consulter ce tableau pour les types de charges suggérés et le programme correspondant. Pour chacun des programmes de la laveuse, les options disponibles sont indiquées à droite.	43
Options disponibles	43
4	43
4	43
4	43
4	43
4	43
4	43
4	43

Match case Limit results 1 per page

Level the Washer

Properly leveling your washer avoids excessive noise and

vibration.

NOTE:

Installing washer on soft floor surfaces, such as carpets or

surfaces with foam backing, is not recommended.

Slide the washer to its final location.

Check that all four feet are in firm contact with the floor.

Check the levelness of the washer by placing a level on the

top edge of the washer, first side to side then front to back.

If the washer is against a wall, move the washer out slightly

before tipping back. If the washer is not level, first prop the

front with a wooden block and adjust the front feet height

moving the hexagonal plastic part as necessary. Repeat to

adjust back feet.

Make sure all four feet are stable and resting on the floor. Then

check that the washer is perfectly level (use a level). Repeat

steps 1-3 until washer is level.

After the washer is level, and all four feet are in firm contact

with the floor, use a

" (14 mm) open-end wrench to turn the

locknuts on the feet, tightly against the washer cabinet.

IMPORTANT:

All four feet must be tightened. If the locknuts

are not tight against the washer cabinet, the washer may

vibrate.

The washer should not move front to back, side to side, or

diagonally when pushed on its top edges.

Confirm the levelness of the washer.

Complete Installation

Check the electrical requirements. Be sure that you have the

correct electrical supply and the recommended grounding

method. See “Electrical Requirements.”

Check that all parts are now installed. If there is an extra part,

go back through the steps to see which step was skipped.

Check that you have all of your tools.

Dispose of/recycle all packaging materials.

Check that the water faucets are on.

Check for leaks around faucets and inlet hoses.

Plug into a grounded 3 prong outlet.

Read “Washer Use.”

To test and to clean your machine, make sure that there are no

clothes in the washer and add one AFFRESH™ tablet to the

washer drum. Select POWER, the CLEAN WASHER cycle and

then select START. This cycle will take approximately 50

minutes to complete. Allow the washer to complete the entire

cycle without interruption.

Electrical

hock Hazard

Plu

into a

rounded

pron

outlet.

Do not remove

round pron

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death,

ﬁre, or electrical shock.

WARNING