Whirlpool WOEC5930LZ Dimension Guide - Page 2
Location Requirements
View all Whirlpool WOEC5930LZ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
DIMENSION GUIDE Location Requirements IMPORTANT: Observe all governing codes and ordinances. ■ Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance with oven. ■ Recessed installation area must provide complete enclosure around the recessed portion of the oven. ■ Grounded electrical supply is required. See "Electrical Requirements" section. ■ Electrical supply junction box should be located 3" (7.6 cm) maximum below the support surface when the oven is installed in a wall cabinet. A 1" (2.5 cm) minimum diameter hole should have been drilled in the right rear or left rear corner of the support surface to pass the appliance cable through to the junction box. ■ Oven support surface must be solid, level and flush with bottom of cabinet cutout. Floor must be able to support a total weight (microwave and built-in oven) of 249 lbs (113 kg) for 30" (76.2 cm) models. IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C). Cabinet Dimensions - Built-in Microwave/Oven Combination Standard Installation A B D F G E 2 of 9 Flush Installation A 25" (63.5 cm) minimum cutout depth is required. These dimensions will result in a 1/4" (6 mm) reveal on the top, a 1/4" (6 mm) reveal on the sides, and a 1/8" (3 mm) reveal on the bottom of the wall oven. The front face of the cleats and platform will be visible and should be treated as a finished surface. FRONT VIEW SIDE VIEW A B C DE F F G G H H J I 30" (76.2 cm) models A. 5/8" (1.6 cm) top cleat* B. 301⁄4" (76.8 cm) minimum width of flush inset cutout C. 287⁄8" (73.3 cm) minimum width of opening D. 445⁄16" (112.5 cm) minimum height of flush inset cutout E. 421⁄2" (107.9 cm) recommended cutout height F. 11/16" (1.7 cm) side cleat* G. 1/2" (1.3 cm) spacer the entire depth of the cutout* H. Recommended junction box location I. 45⁄8"-191⁄4" (11.7-48.9 cm) bottom of cutout to floor J. 25" (63.5 cm) minimum depth of cutout *Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet. TOP VIEW A A C 30" (76.2 cm) models A. 30" (76.2 cm) minimum cabinet width B. 11⁄4" (3.2 cm) top of cutout to bottom of upper cabinet door C. 191⁄4" (48.9 cm) bottom of cutout to floor is recommended. 7.5"-191⁄4" (19.1 cm-48.9 cm) bottom of cutout to floor is acceptable. D. 281⁄2" (72.4 cm) minimum cutout width E. 11⁄2" (3.8 cm) minimum bottom of cutout to top of cabinet door F. 415⁄16" (105 cm)* recommended cutout height G. 24" (60.7 cm) cutout depth *NOTES: The cutout height can be between 411/8" and 411/2" (104.5 cm and 105.6 cm) for microwave/oven combination. C D B D 30" (76.2 cm) models A. 2" (5.1 cm) spacer the entire depth of the cutout* B. 25" (63.5 cm) depth of cutout C. 11⁄2" (3.5 cm) recess from front of cabinet D. 11/16" (1.7 cm) side cleat* *Cleats and spacers must be recessed 13/8" (3.5 cm) from the front of the cabinet.