Whirlpool WRB322DMB Owners Manual - Page 19

Water is leaking from the dispenser system, Water from the dispenser is warm

Get Whirlpool WRB322DMB PDF manuals and user guides View all Whirlpool WRB322DMB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

■■ Refrigerator door closed completely? Close the door firmly. If it does not close completely, see "The doors will not close completely," earlier in this section. ■■ Recently removed the doors? Make sure the water dispenser wire/tube assembly has been properly reconnected. See "Refrigerator Door(s) and Drawer." ■■ Reverse osmosis water filtration system connected to your cold water supply? This can decrease water pressure. See "Water Supply Requirements." Water is leaking from the dispenser system NOTE: One or two drops of water after dispensing is normal. ■■ Glass not being held under the dispenser long enough? Hold the glass under the dispenser 2 to 3 seconds after releasing the dispenser lever. ■■ New installation? Flush the water system. See "Water Dispenser." ■■ Recently changed water filter? Flush the water system. ■■ See "Water Dispenser." ■■ Water on the floor near the base grille? Make sure the water dispenser tube connections are fully tightened. See "Refrigerator Door(s) and Drawer." Water from the dispenser is warm NOTE: Water from the dispenser is only chilled to 50°F (10°C). ■■ New installation? Allow 24 hours after installation for the water supply to cool completely. ■■ Recently dispensed large amount of water? Allow 24 hours for water supply to cool completely. ■■ Water not been recently dispensed? The first glass of water may not be cool. Discard the first glass of water. ■■ Refrigerator connected to a cold water pipe? Make sure the refrigerator is connected to a cold water pipe. See "Water Supply Requirements." 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
19
■
Refrigerator door closed completely?
Close the door firmly.
If it does not close completely, see “The doors will not close
completely,” earlier in this section.
■
Recently removed the doors?
Make sure the water
dispenser wire/tube assembly has been properly
reconnected. See “Refrigerator Door(s) and Drawer.”
■
Reverse osmosis water filtration system connected to your
cold water supply? This can decrease water pressure. See
“Water Supply Requirements.”
Water is leaking from the dispenser system
NOTE:
One or two drops of water after dispensing is normal.
■
Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
■
New installation?
Flush the water system. See “Water
Dispenser.”
■
Recently changed water filter?
Flush the water system.
■
See “Water Dispenser.”
■
Water on the floor near the base grille?
Make sure the
water dispenser tube connections are fully tightened.
See “Refrigerator Door(s) and Drawer.”
Water from the dispenser is warm
NOTE:
Water from the dispenser is only chilled to 50°F (10°C).
■
New installation?
Allow 24 hours after installation for the
water supply to cool completely.
■
Recently dispensed large amount of water?
Allow 24 hours
for water supply to cool completely.
■
Water not been recently dispensed?
The first glass of water
may not be cool. Discard the first glass of water.
■
Refrigerator connected to a cold water pipe?
Make sure
the refrigerator is connected to a cold water pipe.
See “Water Supply Requirements.”